Edimax Technology GS-1026 User Manual

GS-1016 / GS-1026
Quick Installation Guide
11-2011 / v1.0
COPYRIGHT
Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Notes and Cautions
FCC Statement
This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against such interference when operating in a commercial environment. This equipment generates uses and can radiate radio frequency energy, and if not installed and used according to the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his or her own expense will be required to take whatever measures to correct the interference.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE, the essential protection requirement of Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
PRODUCT INTRODUCTION
Model no.:
GS-1016: 16-Port Gigabit Rack-mount Switch GS-1026: 24-Port Gigabit with 2 SFP Slots Rack-mount Switch
Package Contents
Before you start using this router, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s):
Gigabit unmanaged Rack-mount switch (1 pcs) User manual guide (1 pcs) Power cord (1 pcs) Rubber feet (4 pcs) Rack-mount brackets and screws (1 set)
GS-1016 Key Features
Complies with 10M BASE-T specifications of the IEEE 802.3 standard Complies with 100M BASE-TX specifications of the IEEE 802.3u standard Complies with 1000M BASE-T specifications of the IEEE 802.3ab standard Supports full and half duplex for 10/100Mbps, and full duplex for 1000Mbps Provides 256K Bytes packet buffer Wire-speed packet filtering and forwarding rate Provides 8K MAC address Table Store-and-forward architecture filters fragment & CRC error packets Supports IEEE 802.3az energy efficient ethernet Supports auto MDI/MDI-X crossover detecting and auto correction
GS-1026 Key Features
Complies with 10M BASE-T specifications of the IEEE 802.3 standard Complies with 100M BASE-TX specifications of the IEEE 802.3u standard Complies with 1000M BASE-T specifications of the IEEE 802.3ab standard Supports full and half duplex for 10/100Mbps, and full duplex for 1000Mbps Provides 448K Bytes packet buffer Wire-speed packet filtering and forwarding rate Provides 16K MAC address Table Store-and-forward architecture filters fragment & CRC error packets Supports IEEE 802.3az energy efficient ethernet Supports auto MDI/MDI-X crossover detecting and auto correction
Front Panel
LED Name
Light Status
Description
PWR On
Switch on and correctly powered
Off
Switch not powered or not correctly powered
LNK/ACT
On
The port connected
Off
The port not connected
Flashing
The port is activating and transferring /receiving data.
Please refer to the following description for the front panel:
LED Definition:
Back Panel
AC
AC IN : This connects to AC power source. Supported input voltages range from 100 ~ 240V AC at 50 ~ 60Hz.
Power Connector
Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100-240V AC, and 50-60 Hz.
PRODUCT INSTALLATION
In the following there are two ways for your installation. You can select one that suits you.
Desktop Installation
1. Install the switch on a level surface that can support the weight of the unit & the relevant components, and attach the rubber feet to the bottom. The rubber feet cushion the switch and helps protect the case from scratches.
2. Plug the switch to electrical source with the provided power cord.
Rack-Mount Installation
Rack mounting facilitate to an orderly installation when series of network devices being installed.
1. Disconnect all the cables from the switch.
2. Place the unit the right way up on a hard, flat surface with the front facing you.
3. Locate a mounting bracket over the mounting holes on one side of the unit.
4. Insert the screws and fully tighten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
6. Insert the unit into the rack and secure with suitable screws
7. Reconnect all the cables.
Concerning about the installation environment, we strongly recommend:
1. The switch is placed with appropriate ventilation environment. A minimum 25 mm space around the unit is recommended.
2.The switch and the relevant components are away from sources of electrical noise such as radios, transmitters and broadband amplifiers.
3. Avoid from environments beyond recommend moisture.
Loading...