Edimax Technology EW-7733UnD User Manual
Copyright by Edimax Technology Co, LTD. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission of
this company.
This company makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties, merchantability or
fitness for any particular purpose. Any software described in this manual is sold or
licensed "as is". Should the programs prove defective following their purchase, the buyer
(and not this company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from any defect in
the software. Further, this company reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation to notify any person of
such revision or changes.
The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. For more detailed information about this product, please refer to
the User's Manual on the CD-ROM. The software and specifications are subject to change
without notice. Please visit our web site www.edimax.com for the update. All right reserved
including all brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
C A T A L O G
Chapter I: Product Information ................................................................... 4
1-1 Introduction and safety information ................................................................................. 4
1-2 Safety Information .............................................................................................................. 5
1-3 System Requirements ....................................................................................................... 6
1-4 Package Contents .............................................................................................................. 6
1-5 Familiar with your new wireless network card ............................................................... 7
CHAPTER II: Driver Installation and Configuration ........................... 8
2-1 Network Card Installation .................................................................................................. 8
2-2 Connect to Wireless Access Point ................................................................................. 15
2-2-1 Using Edimax Utility .............................................................................................. 16
2-3 Connection Profile Management .................................................................................... 21
2-3-1 Add a new entry..................................................................................................... 21
2-3-2 Remove an existing profile .................................................................................. 25
2-3-3 Edit an existing profile .......................................................................................... 26
2-3-4 Import / Export profile ........................................................................................... 27
2-3-5 WPS Profile Setup ................................................................................................ 29
2-3-5-1 PBC mode WPS configuration ................................................................ 31
2-3-5-2 PIN mode WPS configuration .................................................................. 32
2-4 View Link Status ............................................................................................................... 34
2-5 Advanced Settings ............................................................................................................ 37
2-5-1 ‘Advanced’ menu ................................................................................................... 37
CHAPTER III: Soft-AP Function ................................................................ 38
3-1 Switch to AP Mode and Station Mode ........................................................................... 38
3-2 Configure AP ..................................................................................................................... 39
3-3 Advanced Functionality .................................................................................................... 43
3-4 Access Control .................................................................................................................. 44
3-5 Associate List .................................................................................................................... 46
3-6 About................................................................................................................................... 47
CHAPTER IV: Appendix ........................................................................... 48
4-1 Hardware Specification .................................................................................................... 48
4-2 Troubleshooting ................................................................................................................ 49
4-3 Glossary ............................................................................................................................. 51
Federal Communication Commission ............................................................................. 54
Chapter I: Product Information
1-1 Introduction and safety information
Thank you for purchasing this high-speed wireless dual band network card! This network
card can operate in 2.4GHz or 5GHz wireless network. Excepting common wireless
standards 802.11a/b/g, this wireless network card is also able to access 802.11n wireless
networks - data transfer rate is 450Mbps, and that’s six times faster than 802.11g wireless
network!
With easy-to-install USB 2.0 interface - a very common expansion port of computers - plug
this wireless network card into any empty USB port of your computer, just that simple!
Main Features
Complies with 2.4GHz/5GHz wireless 802.11a/b/g/n standards with data rate up to
450Mbps
Includes multi-language EZmax setup wizard
Supports USB 2.0/1.1 interface
Supports hardware & software WPS configuration function
Supports WMM, WMM-PS (IEEE 802.11e QoS standard)
Supports 64/128-bit WEP, WPA (TKIP with IEEE 802.1x),WPA2 (AES with IEEE
802.1x) for high security level
Supports operating system: Windows XP/Vista/7
* Maximum performance may vary depending on network conditions and environmental
factors.
1-2 Safety Information
In order to keep the safety of users and your properties, please follow the following safety
instructions:
1. This USB wireless network card is designed for indoor use only. DO NOT expose this
network card to direct sun light, rain, or snow.
2. DO NOT put this network card at or near hot or humid places, like kitchen or bathroom.
Also, do not left this wireless network card in the car in summer.
3. This network card is small enough to put in a child’s mouth, and it could cause serious
injury or could be fatal. If they throw the network card, the card will be damaged. PLEASE
KEEP THIS NETWORK CARD OUT THE REACH OF CHILDREN!
4. This network card will become hot when being used for long time (This is normal and is
not a malfunction). DO NOT put the network card on a paper, cloth, or other flammable
objects after the network card has been used for a long time.
5. There’s no user-serviceable part inside the network card. If you found that the network
card is not working properly, please contact your dealer of purchase and ask for help. DO
NOT disassemble the network card by yourself, warranty will be void.
6. If the network card falls into water, DO NOT USE IT AGAIN BEFORE YOU SEND THE
CARD TO THE DEALER OF PURCHASE FOR INSPECTION.
7. If you smell something strange or even see some smoke coming out from the network
card, switch the computer off immediately, and call dealer of purchase for help.
1-3 System Requirements
One CD-ROM drive
Hard Disk : At least 100MB available space
One available USB 2.0 port (May not work on USB 1.1 port, and performance will be
greatly reduced)
Operation System : Windows XP/Vista/7
1-4 Package Contents
Wireless USB Adapter x1
USB Cable x1
Quick Installation Guide x1
CD (EZmax Wizard / Utility, User Manual & Multi-Language QIG) x1
1-5 Familiar with your new wireless network card
LED Name
Light
Status
Description
Link/
Activity
Blinking
Linked to a wireless access point /
Transferring data
Off
Power off
1 2 3
4
1. USB Connector
2. Flippable Antenna
3. Link/Activity LED
4. WPS Button (Press to activate WPS pairing mode)
CHAPTER II: Driver Installation and Configuration
2-1 Network Card Installation
Please follow the following instructions to install your new wireless network card:
1. Insert the USB wireless network card into an empty USB 2.0 port of your computer
when computer is switched on. Never use force to insert the card, if you feel it’s stuck,
flip the card over and try again.
2. The following message will appear on your computer, click ‘Cancel / Close’.
Under Windows XP
Under Windows Vista
3. Software Installation, This wizard can be run in Windows XP/Vista/7. The following
procedures are operated in Windows XP. You can install the Wireless Adapter by
EZMAX Setup Wizard in the CD-ROM including in the package. The wizard is an easy
and quick configuration tool for internet connection with series process.
When you start EZMAX Setup Wizard, you will get the following welcome screen.
Please choose the language to start the configuration. The wizard will guide you to
finish your network connection. We will not provide any instruction for the EZMAX Setup
Wizard here.
If you lose the CD ROM or you prefer the traditional setup procedure,
please follow the instruction as following step.
1. Execute ‘Setup.exe’ program inside the CD then the programs will appear. Please read
the end user license agreement and click ‘I accept the terms of the license agreement’
then click ‘Next’ button, to accept license agreement.
2. It is recommend installing driver and utility if the network card is installing the first time. If
you want to update the driver only, choose ’Install driver only’. Click ‘Next’ to continue.
3. You can choose the configuration tool used to configure the wireless network card here.
It’s recommended to select ‘Edimax Configuration Tool’, which provides fully access to
all functions of this wireless network card. If you prefer to use the wireless configuration
tool provided by Windows XP or Vista, please select ‘Microsoft Zero Configuration Tool’
then click ‘Next’.
4. Now you’ll see the following message, please click ‘Install’ to start utility installation. If
you see ‘Found New Hardware’ message again, please ignore it and
wait.
5. Please wait while the install procedure is running. When you see this message, please
HERE!
click ‘Finish’ to complete the driver installation process.
6. After installation is complete, wireless configuration utility will be shown in the desktop of
your computer automatically. You will also see an icon at the lower-right corner of your
windows system. If you put the mouse cursor on the icon, the status of wireless card will
be displayed as a popup balloon.
7. When you want to configure your wireless connection, please right click on this icon,
and a popup menu will appear. You can click ‘Launch Config Utility’ to start configuration
program. If you want to close the configuration utility, please click ‘Exit’.
8. Please note that if you stopped config utility by ‘Exit’ function, you’ll not be able to
maintain the wireless link to the access point you wish to use. In this case, you can start
config utility again by clicking ‘Edimax Wireless Utility’ icon from ‘Start’ -> ‘All Programs’
-> ‘Edimax Wireless’, as shown below.
2-2 Connect to Wireless Access Point
After the driver is correctly installed, it will try to connect to any unencrypted wireless
access point automatically. If you want to connect to a specific wireless access point, or the
access point you wish to connect uses encryption, you have to configure the wireless
network card and input required parameters, to get connected to the wireless access point
you wish to connect.
The current status of wireless connection will be displayed by Edimax configuration utility
icon:
Wireless connection is established, good signal reception.
Wireless connection is established, normal signal reception.
Wireless connection is established, weak signal reception.
Connection is not established yet.
Wireless network card is not detected.
There are two ways you can configure your wireless network card to connect to wireless
access point: using the Edimax configuration utility and using built-in windows zero
configuration utility.
2-2-1 Using Edimax Utility
HERE!
Please follow the following instructions to use Ralink configuration utility to
connect to wireless access point.
1. Left-click the Ralink configuration utility icon located at lower-right corner of
computer desktop, and configuration menu will appear:
2. Wireless utility will appear.
Click ‘Site Survey’ button to open the list of available wireless
networks (and their status).
Field#
Description
1 (SSID)
The Service-Set IDentifier of network device
(The name of network device)
2 (Type)
The type of network device
Infrastructure (Access Point)
Ad-Hoc
3 (Channel)
The channel number of this network device
4
(Wireless
mode)
Available wireless mode.
802.11a wireless capability
802.11b wireless capability
802.11g wireless capability
802.11n wireless capability
2 3 4 5 6
There are 6 fields in ‘Site Survey’ list:
Loading...