Edimax Technology EW-7722In User Manual

Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.

This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. For more detailed information about this product, please refer to the User's Manual on the CD-ROM. The software and specifications are subject to change without notice. Please visit our web site

product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The equipment version marketed in US is restricted to usage of the channels 1-11 only.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, Bulgaria, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not intended for use

None.

C A T A L O G

CHAPTER I: Product Information ............................................................. 1

1-1 Introduction and safety information ................................................................ 1

1-2 Safety Information ........................................................................................... 2

1-3 System Requirements ...................................................................................... 3

1-4 Package Contents ............................................................................................. 4

1-5 Familiar with your new wireless network card ............................................... 5

CHAPTER II: Driver Installation and Configuration ............................... 6

2-1 Network Card Installation ............................................................................... 6

2-2 Using the Wireless Configuration Utility ...................................................... 14

2-2-1 Using Ralink Utility ........................................................................... 15

2-2-1-1 Scan for Other Wireless Devices ............................................ 17

2-2-1-2 Connect to an Access Point ..................................................... 22

2-2-1-3 Add an Access Point to Profile ................................................ 26

2-2-2 Using Windows Zero Configuration .................................................. 34

2-3 Profile Management ...................................................................................... 38

2-3-1 Add a profile ....................................................................................... 39

2-3-2 Edit an existing profile ....................................................................... 40

2-3-3 Delete an existing profile ................................................................... 41

2-3-4 Activate a profile ................................................................................ 42

2-4 Advanced Settings ......................................................................................... 43

2-5 View Network Statistics ................................................................................ 46

2-6 WMM Setting ................................................................................................ 47

2-7 WPS Configuration ........................................................................................ 50

2-7-1 WPS Setup - PBC (Push-Button Configuration) ................................ 51

2-7-2 WPS Setup - PIN ................................................................................ 54

2-8 Radio On/Off ................................................................................................. 56

2-9 About ............................................................................................................. 57

2-10 On-line Help ................................................................................................ 58

CHAPTER III: Soft-AP Function .............................................................. 59

3-1 Switch to AP Mode and Basic Configuration ................................................ 59

3-2 Security Setting.............................................................................................. 64

3-3 Access Control ............................................................................................... 67

3-4 Connection Table ........................................................................................... 69

3-5 Event Log ...................................................................................................... 71

3-6 Statistics ......................................................................................................... 72

3-7 About ............................................................................................................. 73

CHAPTER IV: Appendix ............................................................................ 74

4-1 Specification .................................................................................................. 74

4-2 Troubleshooting ............................................................................................. 75

4-3 Glossary ......................................................................................................... 77

CHAPTER I: Product Information

1-1 Introduction and safety information

Thank you for purchasing Edimax wireless high-speed wireless network PCI card! Excepting common wireless standards 802.11b/g, this wireless network card is also able to access 802.11n wireless networks - data transfer rate is 150Mbps(EW-7711In)/300Mbps(EW-7722In), and that’s three times faster than 802.11g wireless network!

With easy-to-install PCI interface - a very common expansion port of computers - plug this wireless network card into any empty PCI slot of your computer, just t hat simple!

Other features of this wireless network card including:

 High-efficiency antenna expands the scope of your wireless

network.

 High-speed data transfer rate - Up to 150Mbps (EW-7711In).  High-speed data transfer rate - Up to 300Mbps (EW-7722In)  WMM function: control the bandwidth required for different

applications.

 Work with IEEE 802.11b/g/n wireless devices.  Supports major encryption methods like WEP, WPA, and WPA2

encryption.  WPS configuration - You don’t need an experienced computer

technician to help you to get connected. Utilizing the software

program of the card, you can get your computer connected by

pushing a button or entering an 8-digit code. Pressing the button

on the network card, the WPS connection can be activated as

well.  PCI interface - you can get it installed on your computer in just

few seconds!

1-2 Safety Information

In order to keep the safety of users and your properties, please follow the following safety instructions:

1. This wireless network card is designed for indoor use only. DO NOT expose this network card to direct sun light, rain, or snow.

2. DO NOT put this network card at or near hot or humid places, like kitchen or bathroom. Also, do not left this wireless network card in the car in summer.

3. This network card will become hot when being used for long time (This is normal and is not a malfunction). DO NOT put the network card on a paper, cloth, or other flammable objects after the network card has been used for a long time.

4. There’s no user-serviceable part inside the network card. If you found that the network card is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the network card by your self, warranty will be void.

5. If the network card falls into water, DO NOT USE IT AGAIN BEFORE YOU SEND THE CARD TO THE DEALER OF PURCHASE FOR INSPECTION.

6. If you smell something strange or even see some smoke coming out from the network card, switch the computer off immediately, and call dealer of purchase for help.

1-3 System Requirements

 An empty PCI slot  Windows 2000, XP, Vista, or Windows 7 operating system  CD-ROM drive  At least 100MB of available disk space

1-4 Package Contents

Before you starting to use this wireless network card, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items:

□ PCI Wireless Network Card (1 pcs) ……………………………. 1 □ 2dBi Antenna (1 pcs for EW-7711In) ……………………..……. 2

3dBi Antenna ( 2 pcs for EW-7722In) □ Quick Installation Guide (1 pcs) ………………………….……. 3 □ Driver/Utility/User Manual CD-ROM (1pcs) …..……………… 4

1-5 Familiar with your new wireless network card

Example : EW-7722In

1. Antennas One 3dBi dipole antenna is enclosed with the PCI card. Please secure the antenna to Reverse SMA connector of the card.

2. WPS Button Press this button and hold for 3 seconds to start WPS function. When WPS is enabled, the Link and Tx/Rx LEDs will be steadily on.

3. Link and Tx/Rx LED Definitions

LED Name Light Status Description Link On Link to a wireless access point

Off Radio is switched to off.

Tx/Rx Blinking Transferring / receiving data

Off No wireless activity

CHAPTER II: Driver Installation and Configuration

2-1 Network Card Installation

Please follow the following instructions to install your new wireless network card:

1. SWITCH THE COMPUTER OFF, remove the cover and insert the

wireless network card into an empty PCI slot of your computer and then replace the cover.

2. Install the antenna on the wireless network card, and make sure the

antenna is securely installed. To improve radio reception, please adjust antenna to the proper position.

3. When you restart the computer, this ‘Found New Hardware Wizard’

screen will appear, click ‘Cancel’.

You can install the Wireless Adapter by EZMAX Setup Wizard in the CD-ROM including in the package. The wizard is an easy and quick configuration tool for internet connection with series process. When you start EZMAX Setup Wizard, you will get the following welcome screen. Please choose the language to start the configuration. The wizard will guide you to finish your network connection. We will not provide any instruction for the EZMAX Setup Wizard here.

If you lose the CD ROM or you prefer the traditional setup procedure, please follow the instruction as following step in this quick installation guide.

4. Insert device driver CDROM into the CD/DVD ROM drive of your

computer, and execute ‘Setup.exe’ program. Please read the end user license agreement and click ‘I accept the terms of the license agreement’ then click ‘Next’ button, to accept license agreement.

5. It is recommend installing driver and utility if the network card is

installing the first time. If you want to update the driver only, choose ’Install driver only’. Click ‘Next’ to continue.

6. You can choose the configuration tool used to configure the wireless

network card here. It’s recommended to select ‘Ralink Configuration Tool’, which provides fully access to all functions of this wireless network card. If you prefer to use the wireless configuration tool provided by Windows XP, please select ‘Microsoft Zero Configuration Tool’ then click ‘Next’.

7. Please click ‘Install’ to start utility installation. If you see ‘Found

New Hardware’ message again, please ignore it and wait.

8. Please wait while the install procedure is running. When you see this

message, please click ‘Finish’ to complete the driver installation process.

9. After installation is complete, wireless configuration utility will be

shown in the desktop of your computer automatically. You will also see an icon at the lower-right corner of your windows system. If you put the mouse cursor on the icon, the status of wireless card will be displayed as a popup balloon.

HERE!

When you want to configure your wireless connection, please right click on this icon, and a popup menu will appear. You can click ‘Launch Config Utility’ to start configuration program.

If you want to close the configuration utility, please click ‘Exit’.

Please note that if you stopped config utility by ‘Exit’ function, you’ll not be able to maintain the wireless link to the access point you wish to use. In this case, you can start config utility again by clicking ‘Edimax Wireless Utility’ icon from ‘Start’ -> ‘All Programs’ -> ‘Edimax Wireless’, as shown below.

2-2 Using the Wireless Configuration Utility

There are two ways you can configure your wireless network card to connect to wireless access point: using the Edimax configuration utility and using built-in windows zero configuration utility.

2-2-1 Using Edimax Utility

Please follow the following instructions to use Edimax configuration utility to connect to wireless access point.

1. Right-click the Edimax configuration utility icon located at

lower-right corner of computer desktop and then clicks ‘Launch Config Utility’.

2. Edimax setup utility will launch, and begin to scan for all wireless

access points automatically.

Setup Area

More / Less button

It consists two parts: Menu and setup area. You can select a setup function (Profile, Network, etc.) from menu, and corresponding setup items will be displayed at setup area.

Some function includes more information, and can not be fitted in setup area. In this case, you can click ‘More / less’ button to expand the setup utility window, to display more information:

You can click ‘More / Less’ button again, and setup utility window will resume to its original size.

Tip: If a setup item requires more information to complete the setup procedure, the setup utility window will expand automatically.

2-2-1-1 Scan for Other Wireless Devices

There are two kinds of wireless connection mode: Infrastructure and Ad-Hoc. Infrastructure mode is used by wireless access points, which is able to establish wireless connection for you and other wireless / wired network clients.

Ad-Hoc mode is also know as ‘point-to-point’ mode, and in this mode, wireless devices such as computer or PDA will not be capable to establish wireless connection with more than one wireless device, and is suitable for establishing a one-to-one wireless connection between two wireless devices.

Before you can connect to any wireless access point or device by infrastructure or Ad-Hoc mode, there two things you must know:

a. Wireless device’s ‘SSID’ (Service Set IDentifier, someone will call

it ‘access point’s name’).

You can scan for the SSID of other wireless devices nearby, but if the SSID of the wireless device you wish to connect is hidden, you must know exact SSID before you can establish connection with it.

b. If the wireless device you wish to connect uses encryption, you

must know its encryption key.

Please launch Ralink setup utility and it will scan for wireless access points near by:

Scan results will be displayed here, please check if the wireless device (access point or another computer) with the SSID you wish to connect is shown here.

Scan result includes 6 types of information, they are:

A B C D E

A The SSID (Service Set Identifier) of wireless device. If nothing is displayed here, it means the SSID of this wireless device is hidden.

If a

symbol appears in front of the name of wireless device, means

you’ve established connected with that wireless device.

B The type of this wireless device and the channel number of this wireless device.

Means this wireless device is an access point

Means this wireless device is a computer (Ad-Hoc mode,

point-to-point connection)

C The wireless standard supported by this access point is displayed here.

‘n’ for 802.11n WPS icon access point uses encryption, a key icon

, ‘g; for 802.11g , and ‘b’ for 802.11b .

will appear when the access point supports WPS. If the

will appear.

Note: When the access point supports WPS and WPS icon

appeared, you will not see the key icon

here even through the

access point uses encryption.

D Shows the signal strength of access point by percentage.

E Shows the bar graph of the signal strength.

If you can not see the access point you wish to connect here, please click ‘Rescan’ button to scan for access point again, until the one you preferred is displayed. You may have to click ‘Rescan’ for more than two times before you can see the access point you wish to use here.

If you still can not see the access point you wish to use after clicking ‘Rescan’ for more than five times, please move your computer closer to the location where the wireless access point is, or see instructions in Chapter 4-2 ‘Troubleshoot ing’.

If you wish to see detailed information for a specific access point, please double-click on it, and you’ll be provided with its detailed information.

There are 4 types of technical information:

General: Displays basic information about this access point, such as SSID, MAC Address, authentication / encryption type, channel etc.

WPS: If this access point supports WPS (Wi-Fi Protected Setup), related information will be displayed here.

CCX: If this access point supports CCX (Cisco Compatible eXtension), related information will be displayed here.

802.11n: If this access point complies with 802.11n draft, related information will be displayed here.

+ 61 hidden pages