EDGESTAR _
Dehumidifier
Model: DEP301EW
Owner's Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar dehumidifier and/or to the user. This
dehumidifier isdesigned for domestic indoor use only. Do not use the unit for industrial or commercial use. Any
other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for
electrical and other technical data related to this unit. The unit must be used in a properly grounded wall
outlet. Please read and follow the safety information listed below.
/_Electrical Safety _ _'_
This dehumidifier is designed for indoor use
only Do not use the unit near bath tubs,
swimming pools or other bodies of water
• Do not wet the housing or control panel
• Do not exceed the power outlet ratings
• Do not pull the unit by the cord
• Always turn the unit off and unplug it from
the outlet when cleaning
• Unplug the unit if it is not going to be used
for an extended time period
• Do not operate the unit with a power plug
missing the ground plug, a damaged cord
or a loose socket
• Be sure the dehumidifier is properly
grounded
• Never plug or unplug the unit with wet
hands
• Do not bypass, cut or remove the grounding
plug
• Do not use extension cords or power strips
with this unit You may need to contact your
electrician if it is necessary to use a longer
cord or do not have a grounded outlet Do
not modify the power cord's length or share
the outlet with other appliances It is
recommended the unit be connected on its
own circuit
• Do not start or stop the unit by switching the
circuit's power on and off
• If the power cord is damaged, it must be
replaced by the manufacturer or a
qualified technician
• Never open the unit while it is plugged in
• Immediately unplug the unit if it makes
strange sounds, emits smells or smoke
comes out of it, and contact customer
/_General Safety
This unit is not intended to be used by
children
Children should be supervised to ensure that
they do not play with this product
Do not allow children to play with the controls
or drop any objects into the air outlets or
vents
• Care should be taken when using the unit in a
room with infants, elderly persons, and
children
• Do not place flower vases, containers, or any
objects on top of the unit
• Do not allow anyone to sit on the unit
• Do not climb on or use the unit as a step
• Do not cover the air intake or exhaust vents
with towels, clothes or materials that prevent
air flow
• When using in closets or confined spaces, be
sure to keep doors open to allow proper
ventilation
• Do not use this appliance near flammable gas
or combustibles, such as gasoline, benzene,
thinner, etc
• Do not use in areas where chemicals are
handled
• Do not place the unit near a heat source as
doing so may cause the plastic parts to melt
• Only use in an upright position on a flat, level
surface and provide at least 10 inches of
clearance from any walls or objects
• Route the power cord carefully to avoid
creating a tripping hazard
• When using in closets or confined spaces, be
sure to keep doors open to allow proper
ventilation
• Clean the filters every two weeks or as
_. service j
is not potable or suitable for drinking.
Do not drink or use condensate or wafer
The wafer produced by the dehumidifier \._:_/
drained from the unit as if contains
contaminates and could make you sick
21
Electrical products should not be disposed of
with household waste Please contact your
local recycling center for more information on
how to recycle electronic waste
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ......................................................................................................... 2
INSTALLATION INSTRUCTIONS ........................................................................ 3
CONTROL PANEL OVERVIEW ............................................................................ 4
OPERATING THE CONTROL PANEL ................................................................. 5
POWER ................................................................................................................ 5
A uto-Restart: ................................................................................................ 5
Auto-Shut Off: .............................................................................................. 5
CONTINUOUS MODE ............................................................................................. 5
FAN SPEEDS.......................................................................................................... 5
SETTING THE HUMIDITY LEVEL ................................................................................... 5
LCD DISPLAY ....................................................................................................... 6
Error Codes .................................................................................................. 6
WATER FULL LIGHT ................................................................................................. 6
ADDITIONAL NOTES ABOUT THE DEHUMIDIFIER'S BEHAVIOR: ......................................... 6
DRAINING THE UNIT ............................................................................................ 7
MANUAL DRAIN .................................................................................................... 7
CONTINUOUS DRAIN ............................................................................................. 7
MAINTENANCE .................................................................................................... 8
CLEANING THEUNIT ............................................................................................... 8
CLEANING THEPRE-FILTER....................................................................................... 8
CLEANING THEWATER BUCKET ................................................................................ 8
PREPARATION FOR STORAGE .................................................................................. 9
ENERGY SAVING GUIDE ..................................................................................... 9
TROUBLESHOOTING .......................................................................................... 9
SPECIFICATIONS ............................................................................................... 12
EdgeStar Portable Dehumidifier ii
Introduction
Thank you for purchasing this EdgeStar portable dehumidifier. We are glad
you chose us. We believe fhaf your purchase of this product opens a
relationship between you and EdgeSfar. We will provide the customer
support needed fo nurture fhaf relationship.
This manual contains important information regarding the proper
installation, use and maintenance of your portable dehumidifier. Following
this manual will ensure that your product will work at its peak performance
and efficiency.
Your dehumidifier is designed to remove moisture in the air by
condensation removal and collecting the wafer in a removable bucket,
or draining into a drain hose fhaf can be routed fo a drain hole on the
floor or condensate pump.
Please save the original product packaging in case you need to safely
transport your portable dehumidifier.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located
on the ratings label on the back of your unit and are
needed fo obtain warranty service. You may also want
fo staple your receipt fo this manual as if is the proof of
your purchase, and is also needed for service under
your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer
service:
• If you received a damaged product, immediately contact the
dealer that sold you the product.
• Read and follow this instruction manual carefully to help you install,
use and maintain your portable dehumidifier.
• Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
• Register your product at http://www.edgestar.com and download
product guides, owner's manuals, and access additional
troubleshooting resources.
• If you need warranty service, our friendly customer service
representatives are available via email af service@edgestar.com
or by telephone af 1 (866) 319-5473.
Front View
Parts Identification
Control Panel
Handle
Air Intake
Water Bucket
Water Level Indicator
Back View
Power Plug
Exhaust
Drain Plug
Casters
EdgeStar Portable Dehumidifier 2
f
Note:
Dehumidifiers
working in a
basement will have
little or no effect on
adjacent enclosed
rooms such as
closets, unless there
isenough
circulation of air in
and out of the
enclosed area.
The unit isdesigned
to work in
environments with
temperatures
between 41°F and
9qOF
Installation Instructions
Your dehumidifier will remove moisture from the air and collect the excess
wafer in a bucket. You can use the EdgeSfar dehumidifier fo create a
comfortable environment and prevent damage caused by moisture fo
books or valuables in areas such as basements or home libraries. Follow
the instructions below fo unpack and set up your unit.
1) Carefully unpack the dehumidifier from its box and packaging material,
and remove the adhesive tape holding the wafer bucket and filter in
place. You may want fo save the box for storing and transporting the unit.
Let the unit sit upright for af least 24 hours before powering if on fo allow
the compressor's fluids fo settle.
2) Place the dehumidifier on a level floor or surface that is strong enough
fo support the unit with a full bucket of wafer in a room where the
ambient temperature will not drop below 41°F, and away from any heat
sources such as direct sunlight, heaters, radiators, dryers, etc.
Allow at least 10 inches of space all around the unit and at least 20 inches
of space above the unit.
f
Caution:
The unit isdesigned to be used
indoors and freestanding, and
not be used outdoors, or be
built-in fo a cabinet or used
under a counter.
20
10_
If you have multiple power outlets in the room, choose one that is near the
dehumidifier and fhaf will be able fo provide adequate power fo the unit.
See the power requirements listed on the product label printed on the
side, or on the back of your dehumidifier.
3) Close all windows and doors. To be most effective, use the dehumidifier
in a contained room. For example, use if in a room with four walls and a
ceiling, instead of a partitioned studio, or warehouse.
4) To activate the unit and ensure the warning switches are engaged,
remove the water bucket and reinstall it; otherwise, the unit may not work
properly.
5) Plug the unit in to a grounded outlet. (Read the Safety Information
section.)
6) When first using the unit, press the Power button on the top of the unit
and run if in continuous mode for 24 hours.
Control Panel Overview
Filter
o
Ful
cD
Cont.
c]
On Off Autodeffost
c_ c_ o
Turbo
o
Normal
cY_
Timer
Button Function
The check filter feature is a reminder fo clean the air filter for a
more efficient operation. The Filter light will illuminate after 250
hours of operation. To reset after cleaning the filter, press the Filter
button and the indicator light will shut off.
(_ ets the unit fo run continuously until the wafer bucket is full. You
will not be able fo use the increase/decrease humidify buttons.
Sets the fan speed from normal fo turbo for your desired level of
moisture removal.
Powers the unit on or off.
Note: The unit is not a
humidifier; using the increase
humidify button will not add
moisture fo the air.
(_ Increases the desired relative humidify setting for damper air.
Decreases the desired relative humidify setting for drier air.
Press to initiate the auto start and auto stop feature in conjunction
with the increase and decrease buttons.
Indicator Light Function
Filter Lights up to indicate the filter needs to be cleaned.
Full
Cont. Lights up when the unit is set to run continuously until
On/Off Lights up to indicate if the unit isin on or off position.
Turbo Lights up to indicate the fan is on the high setting.
Normal Lights up to indicate the fan is on the low setting.
Auto-Defrost Lights up to indicate the auto defrost operation is on
LCD Display Displays the level of humidity as well as error codes.
The water full light will light up red if the unit has filled
the water bucket.
the water bucket is full.
EdgeStar Portable Dehumidifier 4
Operating the Control Panel
Power
Continuous Mode
Use the "Power" button to turn the portable dehumidifier on and off. By
default when you first use the power button, the unit will begin fo operate
in normal fan speed mode.
Note: If the unit was powered off, waif af least 3 minutes before powering
if back on.
Auto-Restart: If power fo the unit is interrupted, the dehumidifier will restart
itself in with the last used mode/settings once the power is restored. The
compressor will restart after 3 minutes.
Auto-Shut Off: The unit will shut off when the set humidify has been
reached, or when the wafer bucket is full, has been removed, or is not in
its proper position.
Continuous mode dehumidifies the air until the wafer bucket is full. Use the
continuous mode for maximum dehumidification. You will not be able fo
use the set humidify buttons.
To operate the unit in continuous mode:
1) Make sure the power cord is plugged into a power outlet.
2) Press the "Power" button.
3) Press the "Conf." button. The LED indicator next fo "Conf." will light up.
4) Select the fan speed by using the Normal or High button.
Fan Speeds
Setting the Humidity Level
f
Note: Relative Humidity (RH)is
the ratio of the actual wafer
content of the air at a given
temperature to the potential
water content af fhaf same
temperature.
The dehumidifier has two fan speeds. Use the turbo fan speed for
maximum moisture removal. Use the normal fan speed for quieter
operation.
Select the fan speed by pressing the "Fan" button until desired mode is
illuminated
The desired humidify level can be set within a range of 35% Relative
Humidify (RH) fo 80% RH in 5% increments.
]) Make sure the power cord is plugged into a power outlet.
2) Press the Power button. Make sure the "Conf." light is fumed off.
3) Press the "Increase" and "Decrease" buttons fo set the desired humidify
To set the desired humidify level percentage:
level. After a few seconds, the LCD display will revert fo the acfuat room
humidify level with +5% accuracy. For drier air use the "Decrease" button.
Operating the Control Panel continued
LCD Display
The LCD Display will show the room's relative humidity percentage by
default. Pressing the Increase and Decrease buttons will show the set
humidity for a few seconds, and then revert to the room's relative
humidity.
Error Codes
In addition to showing the humidify, the display may show the following
error codes:
AS - Humidity sensor error
Power the unit off, and then unplug the unit for 15 minutes. Plug in and
power on. If the issue persists, please contact customer service.
ES- Temperature sensor error
Power the unit off, and then unplug the unit for 15 minutes. Plug in and
power on. If the issue persists, please contact customer service.
EC - Unit malfunction
Please make sure whether the ambient temperature is suitable for the
stated temperature in the manual or not. If not, please operate the unit
under the stated temperature. If the environment temperature issuitable
for the stated temperature, please contact customer service.
P2- Bucket is full
Empty the water bucket and reinstall it.
Water Full Light
The Water Full Light will illuminate when the bucket isready to be emptied.
The light also turns on when the bucket is not installed or installed
incorrectly. Once the wafer is drained, and the bucket is properly
installed, the unit will operate normally.
Additional notes about the dehumidifier's behavior:
• Once the unit reaches the desired set humidify, the power button will
remain lit while the compressor and fan shuts off. You will not be able
fo change the fan speed.
• If the power fo the unit was interrupted while the compressor was
running, the unit may take a few minutes to start the fan and
compressor.
• If the room's relative humidity is lower than the set humidity, the unit
will not start the fan and compressor unless you set the unit to run in
Continuous mode.
EdgeStar Portable Dehumidifier 6
Draining the Unit
Manual Drain
@
Warning: The wafer produced by
the dehumidifier is not potable or
suitable for drinking.
Do not drink the wafer drained
from the unit as if contains
contaminates and could make
you sick.
The dehumidifier can be drained manually using the water bucket. When
the bucket is full, the unit will automatically stop running, and the wafer full
light will turn on.
Follow the steps fo remove the bucket and dump the wafer.
1) Slowly and carefully pull the
bucket out by the handles until
you see the bucket handle.
3) Pour the water out. Do not place the bucket on the floor as its bottom is
uneven and will fall down.
4) Reinstall the bucket.
2) Pull the bucket up by its
handle
Continuous Drain
The dehumidifier can be drained continuously fo a floor drain.
]) Remove the water bucket from the unit, and you will find a hose
connector. You can use a ]2 mm hose fo attach fo the connector.
Connector
/
Drain hose
2) Remove the rubber plug from the back of the unit's drain hose outlet,
and push the drain hose through.
3) Securely attach the drain hose fo the connector. Lead the other end of
the hose fo a floor drain or other suitable drainage port.
4) You must reinstall the wafer bucket.
Maintenance
Clean the dehumidifier and filters regularly to maintain performance and
efficiency, and prolong the unit's life. Be sure to always unplug the
dehumidifier from the power outlet before cleaning.
Cleaning the unit
Cleaning the pre-filter Clean the pre-filter periodically to prolong the unit's life, and keep the unit
Use a soft dry cloth to wipe the body clean. If necessary, use lukewarm
water to dampen a cloth to clean the unit. Use a soft bristle brush and
vacuum cleaner to clean between the air intake and exhaust vents.
Never use abrasive chemicals, volatile substances, gasoline, detergents,
chemically treated cloths, or other cleaning solvents that may damage
the cabinet exterior.
Never spray water directly on the unit.
running efficiently. Lint, dust, and dirt can clog the unit and reduce its
performance and effectiveness. If the unit is used in a dusty environment
you may need to clean it on a weekly basis.
To clean the pre-filter, follow the steps below:
1) Power off the unit and remove the pre-filter.
-ZT ................................................ZZ "Z'ZI-ZZZi
NOTE: Do not put the filter in a
dishwasher.
[
Cleaning the water bucket Wash the water bucket frequently to prevent the growth of bacteria,
bucket in a dishwasher.
NOTE: Do not put the wafer
dirt, then rinse thoroughly under lukewarm running water (below 104°F).
2) Use a vacuum cleaner or tap the filter lightly to remove loose dust and
You may use a mild soap and water solution if needed. Allow the pre-filter
to air dry in a cool and shaded place. Dry thoroughly before reinstalling.
3) Reinsert the pre-filter.
Warning: Never operate the unit without the air filter.
mildew and mold.
To clean the water bucket, follow the steps below:
1) Remove the wafer bucket from the unit.
2) Wash the bucket with clean wafer and a mild detergent. Rinse the
bucket thoroughly.
3) Install the wafer bucket.
EdgeStar Portable Dehumidifier 8
Preparation for Storage
Maintenance continued
If you are not going to be using fhe unif for an exfended period of time,
follow fhe insfrucfions below before sforing your unif:
]) Turn off fhe unif and waif 24 hours before empfying fhe wafer lank.
2) Drain all fhe wafer from fhe wafer lank.
3) Clean fhe air filler, wafer lank and unif.
4) Unplug and carefully wind fhe power cord.
5) Cover fhe unif wifh a plastic bag.
6) Sfore fhe unif in an uprighf position in a dry, well-venfilafed place.
Energy Saving Guide
Read and follow fhe guide below fo gel fhe besf performance and
efficiency from your porfable dehumidifier:
• Do nor cover fhe air ouflef (exhausf) while in use.
• Do nor place fhe unif in fronf of curfains or drapes- fo ensure fhey do
nor obsfrucf fhe air infake.
• Keep curfains, blinds or drapes closed during fhe sunniesf parr of fhe
day.
• Close all windows and doors.
• Indoor relative humidify should ideally be kepf befween 35 and 60
percenf depending on fhe ambienf femperafure.
• Make sure fhe unif ison a level surface.
• To prolong fhe compressor's life, please waif af leasf 3 minufes before
fuming fhe unif back on affer shuffing if off.
• Inspecf and keep fhe pre-filfers clean by cleaning regularly.
• Perform roufine mainfenance.
Troubleshooting
Follow the troubleshooting chart fo resolve common issues.
Issue
My dehumidifier does
not dry the air
Frost appears on the
coils
My dehumidifier is not
functioning at all
My dehumidifier is
making a loud noise
My dehumidifier is
making a continuous
metallic knocking or
pinging sound
Possible Cause
Insufficient time fo dry
Air intake or Exhaust
vents are blocked
Humidify control may
not be set low enough
Opened windows or
doors
Room temperature is
too low (below 41°F)
There is a kerosene
heater or something
giving off wafer vapor
in the room
This is normal behavior
Unit is not receiving
power
Insufficient power
Water bucket is full
Water bucket is not in
proper position
Control panel is
disconnected
The unit is not level
A foreign object has
jammed the fan
The floor below the unit
is uneven
Air filter is clogged
Unit may have been
shipped on its side
Damaged compressor
Solution
Run the unit for a
longer period of time.
Make sure there are no
towels, curtains, or
furniture blocking the
front and back of the
unit.
Lower the humidify
control. Run the unit in
continuous mode.
Close all windows and
doors.
Increase the room
temperature.
Remove any device
producing wafer
vapor.
The dehumidifier has
an auto-defrost
feature.
Make sure the unit is
plugged in.
Move the unit fo
another outlet. Check
your circuit breaker.
(Refer fo the rating
label on the back of
the unit fo determine
the Amperage draw).
Drain the unit and
restart.
Remove bucket and
reinserf.
If no indicator lights
turn on, contact
customer service.
Make sure the unit ison
a level surface.
Shut off the unit, and
remove the object
from the fan.
Move the unit fo a
level surface.
Clean the air filter.
Shut off the unit. Let
the unit sit on a level
surface for af least 24
hours and restart.
Contact customer
service.
EdgeStar Portable Dehumidifier 10
Troubleshooting continued...
A drain hose has been
My dehumidifier is
leaking
My dehumidifier runs
for a little while and
then it trips the power
cord or the circuit
breaker
The control panel lights
blink randomly
Unit has an AS error
Unit has an ESerror
Unit has a EC error
Unit has a P2 error
attached and is loose
Cracked water bucket
The dehumidifier may
be plugged into an
outlet that can not
supply the correct
amount of current
Unit may have a faulty
control panel
Humidify sensor error
Temperature sensor
error
Unit malfunction
Bucket is full
Bucket is not correctly
installed
Secure the drain hose.
Route your drain hose
to a drain hole or
condensate pump.
Contact custom.er
service.
Contact an electrician
if the unit works in a
different room or
circuit.
Restart the unit, and if
issue persists, contact
customer service.
Restart the unit, and if
issue persists, contact
customer service.
Restart the unit, and if
issue persists, contact
customer service.
Make sure the ambient
temperature is suitable
for the unit (41°F -
95°F). If not please
operate the unit under
the stated
temperature.
If the ambient
temperature is suitable,
please contact
customer service.
Empty the bucket and
reinstall.
Remove the bucket
and reinstall.
11
Specifications
Description of product
Model
Voltage/Frequency
Power Consumption
Operating Current
Water Bucket Capacity
Dehumidifying Capacity @ 80F
RH60%
Portable Dehumidifier
DEP301EW
AC 115V-60Hz
310W
3.0A
3.5 Liters / .92 Gallons
30 Pints/Day
Refrigerant
Dimensions
WxDxH
Weight
R410A
143/16"x913/16"x197/8"
29 Ibs.
EdgeStar Portable Dehumidifier 12
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions
set forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at
an authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts,
or exchange the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will
carry the remaining warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be
responsible for labor charges incurred. All defective products and parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may request a defective part be returned in exchange for the replacement
part. All replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by
EdgeStar under warranty service become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during
operation of the product under normal service, maintenance, and usage conditions. This warranty applies to the
purchase and use of this product in residential settings within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
,, Labor charges for installation, setup or training to use the product.
,, Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
,, Cosmetic damage such as scratches and dents.
,, Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
,, Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
,, Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses
contrary to instructions provided in the owner's manual, accidents, acts of God, vermin, fire, flood, improper installation,
unauthorized service, maintenance negligence, unauthorized installation or modification, or commercial use.
,, Labor charges incurred 91 days or more after the date d original purchase.
,, The use of EdgeStar products in commercial settings.
,, Optional accessories, attachments, and appearance items.
,, Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar.
• Products lost in shipment, or theft.
,, Products sold AS IS or from an unauthorized reseller.
,, Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and
warranty service at 1-866-319-5473. Please have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the
product must be returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping
related costs to and from the repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling
or improper packaging. Do not return a defective product to the place of purchase. Products received without a return
authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER
THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS,
OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE.
EdgeStar Beverage Cooler
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner's manuals, access additional
troubleshooting resources, and obtain more information on other great
EdgeStar & Koldfront products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2012 Living Direct, Inc. All rights reserved.
Loading...