Combo Washer/Dryer
CWD1510W
Owner's Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
IMPORTANT SAFETY IN FORMATION
Improper handling can cause serious damage to the EdgeStar combo and/or injury to the user. This combo
washer/dryer is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any
other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for
electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
• Do not exceed the power outlet ratings.
• If is recommended that the combo washer/dryer be connected on its
own circuit.
• A standard electrical supply (115 V, 60Hz), that is properly grounded in
accordance with the National Electrical Code and local codes and
ordinances is required.
• Do not use outlets that can be turned off by a switch or pull chain.
• Always turn the unit off and unplug if from the outlet when cleaning.
• Unplug the unit if if is not going to be used for an extended period of time.
• Do not operate the unit with a power plug that is missing the ground plug,
a damaged cord or a loose socket.
• Be sure the combo is properly grounded.
Ele0tricai Shock Hazard
• Never plug or unplug the unit with wet hands.
• Do not bypass, cut or remove the grounding plug.
• Do not use extension cords or power strips with this unit. You may need to
contact your electrician if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the power cord's length or
share the outlet with other appliances. If you must use an extension cord,
use No.]4AWG minimum size and rated no less than 1875 watts.
• Do not start or stop the unit by switching the circuit's power on and off.
• If the power cord is damaged, if must be replaced by the manufacturer
or a qualified technician.
• Never repair the unit while if is plugged in.
• Immediately unplug the unit if if makes strange sounds, emits an odor or
smoke comes out of if, and contact customer service.
• Do not remove any part of the casing unless instructed by an authorized
technician.
• You should never attempt to repair the unit yourself.
• Contact EdgeStar Support if the unit needs repair service.
• Before the appliance is removed from service or discarded, remove the
door and cut off the power cord.
Note:
The Important Safeguards and Warnings indicated in this manual do not
cover all possible conditions which may occur. Common sense, caution
and care must be exercised when installing, maintaining or operating the
washing machine.
Always contact your dealer or service agent or the manufacturer about
any problems or conditions fhaf you do not fully understand.
General Safety
• Do not wash articles that have been previously cleaned in, washed in,
soaked in, or spotted with gasoline, dry-cleaning solvents, or other
flammable or explosive substances, as they give off vapors that could
ignite or explode.
• Do not add gasoline, dry-cleaning solvents, or other flammable or
explosive substances to the wash wafer. These substances give off
vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot-
wafer system that has not been used for 2 weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If the hot-wafer system has not been used for such
a period, before using a washing machine, turn on all hot-wafer
faucets and let the wafer flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas is flammable, do
not smoke or use an open flame during this time.
• Always unplug the washing machine from the power supply before
attempting any service. Disconnect the power cord by grasping the
plug, not the cord.
• To reduce the risk of fire- clothes, cleaning rags, mop heads and the
like which have traces of any flammable substance, such as
vegetable oil, cooking oil, petroleum based oils or distillates, waxes,
fats, etc., must not be placed in the washing machine. These items
may contain flammable substances which, even after washing, may
smoke or ignite in the dryer mode.
• Do not allow children to play on or in the appliance.
• Pets and children may climb into the machine. Check the machine
before every operation.
• Glass door or protector may be very hot during operation. Keep
children and pets far away from the machine during the operation.
• This machine is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the machine by a person responsible
for their safety.
• Do not wash fiberglass materials in this unit (such as curtains and
window coverings that use fiberglass materials). Small particles may
remain in the washing machine and stick to fabrics in subsequent
wash loads causing skin irritation.
• Do not reach into the appliance if the tub or agitator is moving.
• Do not install or store this appliance where if will be exposed to the
weather.
• Do not tamper with controls.
• Do not repair or replace any part of the appliance or attempt any
servicing unless specifically recommended in the user-maintenance
instructions or in published user-repair instructions that you understand
and have the skills to carry out.
• Never stop a fumble dryer before the end of the program. Always
allow the unit to complete the cool down cycle to prolong the life of
the unit.
• Disconnect from the power socket before cleaning or maintenance.
• Make sure that all pockets are emptied. Remove all foreign objects
from pockets of clothing.
• Sharp and rigid items such as coins, nails, screws, stones etc. may
cause serious damage to this machine.
EdgeStar Washer/Dryer Combo ii
• Disconnect power and water supply after operation. Pull out its plug
and cut off water supply after the operation. Please check whether
the water inside the drum has been drained before opening its door.
Please do not open the door if there is any water visible.
• Do not try to repair any internal components by yourself, contact a
qualified service technician for non-user repair issues.
• If the plug (power cord) is damaged, it shall be replaced by the
manufacturer or a service agent to avoid any danger.
• This machine shall be repaired only by an authorized service center.
Only genuine replacement parts should be used.
• This appliance is intended for use only with fabrics that have been
washed with water as a cleaning agent.
• To reduce the risk of fire, do not dry articles containing foam rubber or
similarly textured materials.
• If connected to a circuit protected by fuses, use time-delay fuses with
this appliance.
• Do not climb up and sit on the top cover of the machine.
• Do not lean against the machine door.
• Please do not close the door with excessive forces. If if is found difficult fo
close the door, please check for obstruction.
Before operating this machine
• IMPORTANT: Before operating this machine, all packaging and
transport "shipping" bolts must be removed. Otherwise, the washing
machine may be seriously damaged during operation. Please review
instructions to ensure proper removal of transportation "shipping"
bolts.
• Packing materials may be dangerous to children. Please keep all
packing materials out of children's reach.
• Washing machine shall not be installed in bath room or very wet
rooms as well as in the rooms with explosive or caustic gases.
• Make sure that the water and electrical connections are in
accordance with the installation instructions and local safety
regulations.
• Before washing clothes for the first time, the washing machine should
be operated in cotton cycle with hot water to remove any
contaminants.
• This washing machine is for indoor use only.
iii
Table of Contents
IMPORTANT SAFETY INFORMATION ..................................................................... I
INTRODUCTION ................................................................................................... 1
PARTSIDENTIFICATION ....................................................................................... 2
FRONT ViEW ............................................................................................................ 2
BACK ViEW ............................................................................................................. 3
DETERGENT DISPENSER ............................................................................................. 4
PREPARATION FOR INSTALLATION...................................................................... 4
ELECTRICAL REQUIREMENTS ....................................................................................... 5
LOCATION REQUIREMENTS ........................................................................................ 5
INSTALLATION CLEARANCES ...................................................................................... 6
Washer Dimensions: .................................................................................... 6
TOOLS AND PARTS ................................................................................................... 7
INSTALLATION ............................................. ERROR! BOOKMARK NOT DEFINED.
REMOVE TRANSPORT BOLTS....................................................................................... 7
CONNECT INLET PIPE ................................................................................................ 7
INSTALL INLET PIPE..................................................................................................... 8
DRAIN SYSTEM OPTIONS: .......................................................................................... 9
Standpipe drain system .............................................................................. 9
Laundry tub drain system ........................................................................... 9
Floor drain system ........................................................................................ 9
LEVEL THE WASHER ................................................................................................. 10
OPERATING INSTRUCTIONS .............................................................................. 12
CONTROL PANEL OVERVIEW .................................................................................. ] 2
Control Knob ............................................................................................. 12
LED Display ................................................................................................. 14
TiPS BEFORE WASHING ............................................................................................ ] 6
Washing capacity: .................................................................................... 18
OPERATING THE WASHER ........................................................................................ ] 9
CARE AND MAINTENANCE ............................................................................... 21
CLEANING THEEXTERIOR OF THEUNIT ....................................................................... 21
CLEANING THEINTERIOR OF THE UNIT........................................................................ 21
CLEANING DETERGENT DISPENSER............................................................................ 21
CLEAN INLET FILTER................................................................................................. 22
REMOVE FOREIGN MATTERS FROM COIN TRAP .......................................................... 22
SPECIFICATIONS ............................................................................................... 24
Thisowner's manual isprovided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of
your combo for the latest technical information.
EdgeStar Washer/Dryer Combo iv
INTRODUCTION
Thank you for purchasing this EdgeStar combo washer/dryer. We are glad
you chose us. We believe that your purchase of this product opens a
relationship between you and EdgeStar. We will provide the customer
support needed to nurture that relationship.
This manual contains important information regarding the proper
installation, use and maintenance of your combo. Following this manual
will ensure that your product will work at its peak performance and
efficiency.
Please save the original product packaging in case you need to safely
transport your Combo Washer/Dryer.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located
on the ratings label on the back of your unit and are
required to obtain warranty service. You may also want
to staple your receipt to this manual as it is the proof of
your purchase, and is also needed for service under
your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer
service:
• If you received a damaged product, immediately contact the
dealer that sold you the product.
• Read and follow this instruction manual carefully to help you install,
use and maintain your combo washer/dryer.
• Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
• Visit us on the web at http://www.edgestar.com to register your
product, download product manuals, and access additional
troubleshooting resources and up-to-date information.
• If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com
or by telephone at 1 (866) 319-5473.
PARTS IDENTIFICATION
Front View
I
O
Detergent Dispensing Drawer- There is three compartments for prewash, main wash,
and fabric softener.
Glass Door- Extra-large door with lock. Door automatically locks during operation to
prevent door opening before wafer level has lowered.
Leveling Feet- The unit comes with four adjustable leveling feet for spaces with uneven
floors. Combo Washer should always be level fo efficiently operate.
Coin Trap- Objects that either come loose from clothing or were in pockets will pass
through wash cycle and end up in the coin trap. The coin trap should be cleared out
regularly.
Large Capacity Stainless-Steel Drum- Extra-large capacity drum fo efficiently wash
and dry. Note: To properly wash and dry the unit should not be overloaded.
Control Panel with LEDDisplay- LED Display Panel and Control Dial allow you to choose
the correct setting and customize your wash cycle.
EdgeStar Washer/Dryer Combo 2
Back View
Electrical Plug- Thisunit is supplied with a three prong plug. Please check electrical
requirements before connecting the unit.
Drain Hose- The drain hose directs the flow of wafer after the wash cycle. The drain
hose should always be properly secured fo avoid risk of flooding and/or property
damage.
Water Inlet Valve- There are two wafer inter valves: The left side is hot and the right side
is cold. Connect the two hoses bundled with the unit fo the tap connection.
Detergent Dispenser
Your washing machine is designed for use with only High-Efficiency (HE)
detergents. They are formulated specifically for front-load washers and
contain suds-reducing agents.
Using a regular detergent that is not High-Efficiency may cause over-
sudsing and may affect the unit's performance.
Designed specially to use only
HE(High-Efficiency)detergent
®
EdgeStar Washer/Dryer Combo 4
Release Tab- To remove the dispenser drawer from unit, push
down on the release tab and pull drawer out.
_[ -Main Detergent and Bleach Compartment
-Fabric Softener Compartment
-Pre-Detergent and Washing Powder Compartment
Note: When you plan to dispose
ofthismachine in the future,
please comply with the local
waste disposalregulations.
Remove the door so that
children and pets will not be
trapped in the machine.
PREPARATION FOR INSTALLATION
Electrical Requirements
Failure to follow electrical requirements can cause personal injury, fire, or
electrical shock. Install the combo washer/dryer according to the
manufacturer's instructions and local codes. To reduce the risk of severe
injury or death, follow all installation instructions. Save these instructions
even after installation is complete.
• Properly ground in accordance with all local codes and
ordinances. If there is a short circuit, proper grounding can reduce
the danger of electrical shock.
• It is the responsibility and obligation of the product owner to have
a proper outlet installed by a qualified technician.
• This washer is equipped with a properly grounded 3 prong plug.
• Do not remove ground prong. Do not use an adapter or extension
cord. Plug into a grounded 3 prong outlet.
• Do not overload the outlet with more than one appliance.
Location Requirements
Selecting the proper location for your washer improves performance and
minimizes noise and possible washer "walk". Your washer can be installed
under a custom counter, or in a basement, laundry room, closet, or
recessed area. Proper installation is your responsibility.
You will need:
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 6 ft. (1.8 m) of where
the power cord is attached to the back of the washer. See
"Electrical Requirements."
• Hot and cold wafer faucets located within 4 ft. (1.2 m) of the hot
and cold wafer fill valves, and wafer pressure of 20 - 100 psi (137.9 -
689.6 kPa).
• A level floor with a maximum slope of 1" (25 mm) under entire
washer.
• Washer should be installed on a rigid, dry, and level surface. Soft
floor surfaces such as carpets or surfaces with foam backing are
not recommended.
• A sturdy and solid floor to support the washer with a total weight
{water and load) of 200 Ibs.
• Store and install the washer where it will not be exposed to
outdoor weather conditions.
• Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
• Avoid direct sunlight and make sure there is sufficient ventilation.
• Keep far away from heat sources such as coat or gas.
• Make sure that the washing machine will not stand on its power
cord and is accessible.
Installation clearances
• The Iocafion musf be large enough fo atlow fhe washer door fo be
fully opened.
• Addifionat spacing should be considered for ease of insfallafion
and servicing. The door opens more fhan 90°, and if is nor
reversible.
• Addifionat clearances mighf be required for woN, door, and floor
moldings.
• Addifionat spacing of ] inch on atl sides of fhe washer is
recommended fo reduce noise fransfer
• Make sure fhe combo isinsfatled in a Iocafion where you ore able
fo access fhe elecfricat ouflef.
The dimensions shown ore for recommended spacing and cusfom undercounfer insfallafion.
T
[
(SSOm_
T ]
[
EdgeStar Washer/Dryer Combo 6
Water Hoses (2)
Transportation
"Shippinq" Pluqs
©©
©
NOTE: As you unpack
your unit you may
find some residual
water in the drum
and/or coin trap as
we test all of our units
for quality assurance.
_ •
Tools and Parts
Gather the required tools and accessories (Water hoses (2) and
Transportation "Shipping" Plugs are supplied with unit) before staffing
installation. The accessories supplied are located in the washer drum.
• 6mm nut driver 10mm socket with ratchet
• 10 mm open-end wrench
• Adjustable wrench or I lmm socket with ratchet
• Adjustable wrench or ]4mm open- end wrench
• Channel-lock adjustable pliers
• Carpenter's level
• Wafer Hoses (2)- provided in drum
• Cable Tie
• Transportation "Shipping" Hole Plugs (4)- provided in drum
Unpacking the washing machine
Unpack your washer/dryer combo and inspect for damage that may
have occurred during transportation. If there is any damage fo the
washing machine or any item is missing, please contact your dealer
immediately. Important, you will need all of your packaging including
transportation "shipping" bolts if you need fo send back fo manufacturer.
Dispose of the packing materials: The packing materials of this machine
may be dangerous to children. Once you have inspected machine and
find unit satisfactory, please dispose of them properly. Please dispose the
related packing materials according to the relevant local regulations.
Remove transport bolts
Before using this washing machine, transport "shipping" bolts must be
removed from the backside of this machine. Please follow the steps below
fo remove the transport bolts:
1. Loosen all bolts and completely remove them along with the bushings
(bearings).
2. Cover the holes with transport hole plugs.
3. Important- Keep the transport "shipping" bolts for future use.
Transportatio n
"Shipping" Bolts
INSTALLATION
Connect inlet pipe
Connect the inlet pipe as indicated in the figure below.
Connect the hot inlet valve fo the hot wafer tap and cold inlet valve fo
the cold wafer tap.
............... i!!;4
,i' _i__
Install inlet pipe
Connect the elbow fo the inlet valve af the backside of washing machine
and fasten if fuming clockwise. Connect the other end of inlet pipe fo the
tap and fasten the pipe tightly clockwise.
Note: After connection, if there is any leakage from hose, then repeat the steps fo
connect inlet pipe. The most common type of tap should be used fo supply wafer.
If tap is square or too big, a new tap is required.
EdgeStar Washer/Dryer Combo 8
Drain System Options:
Standpipe drain system - wall or floor (views A & B) - The standpipe drain
requires a minimum diameter standpipe of 2" (50 mm). The minimum
carry-away capacity can be no less than ] 7 gal. (64 L) per minute. The
fop of the standpipe must be af least 24" high and no higher than 39"
from the bottom of the washer.
Laundry tub drain system (view C) - The laundry tub needs a minimum 20
gal. (76 L) capacity. The fop of the laundry tub must be af least 24" above
the floor.
Floor drain system (view D) - The floor drain system requires a siphon break
fhaf may be purchased separately. See "Tools and Pads" on page 7. The
siphon break must be a minimum of 28" (7]0 mm) from the bottom of the
washer. Additional hoses may be needed.
D
f
Level the washer
When positioning the washer/dryer combo, please first check if the legs
are closely attached fo the cabinet. If not, please turn them fo their
original positions by hand or with wrench and tighten the nuts with
wrench.
After positioning the washing machine, apply pressure on each corner of
the combo in sequence. If the unit is unstable when being pressed, the
legs must be adjusted fo level the machine.
, ii ............
Ensure the positioning status of the machine. Loosen the lock nut with a
wrench and turn the leg by hand until if closely contacts the floor. Hold
the leg with one hand and fasten the nut closely fo the cabinet with the
other hand.
After being locked properly, press down on each corner of unit again fo
make sure fhaf they have been adjusted properly. If if isstill unstable,
repeat steps above until unit has no give. Af this time, double check by
placing a level on fop surface of the unit fo ensure unit is properly
adjusted.
EdgeStar Washer/Dryer Combo 10
Electrical Connection
• As the maximum current through the unit is 12A when you are using its
heating function, please make sure the power supply system (current,
power voltage and wire) at your home can meet the normal loading
requirements of the electrical appliances.
• Please connect the power fo a socket which is correctly installed and
properly grounded.
• Make sure the power supply voltage is compatible with the machine's
rating label.
• Power plug must match the socket and cabinet must be properly and
effectively grounded.
• Do not use a multi-purpose plug or socket as an extension cord.
• Do not touch the electrical cord or plug with wet hands.
• When disconnecting hold the plug tightly and pull. Do not pull power cord
forcibly.
• If power cord is damaged or has any sign of wear, a suitable cord must
be purchased from manufacturer or service center for replacement.
11
OPERATING INSTRUCTIONS
Please read the operation instructions carefully to avoid unnecessary
service calls and damages to clothes.
Control Panel Overview
Control Knob
Co_on/NormaI Speed Wash
Delicate
Hand Wash
/Wool
BabyWear
Se|fC_ean
Dry @
Hold 3 Sec
Add Garment
Power
Start/
Pause
Power- Press to start the display panel. If the display is active, press to put
the washer into standby mode.
Start/Pause- Press to start desired wash cycle. If the washer is running,
pressing it once will pause the washer. Press again to restart the wash
cycle. NOTE: If the washer ispaused and the cycle is not restarted within
10minutes, the current wash cycle will be cancelled.
Wash/Dry Cycles
Cotton/Normal- Select this option for normally soiled cottons and mixed
fabrics. The washing period is longer and washes with more agitation.
Recommended fabric types- Cotton, jeans, linen, towels, shirts, sheets,
etc.
Bulky/Large- Select this option for larger items such as blankets and
comforters. The washing period is longer for this cycle.
Permanent Press-Select this option for articles that have been treated
with a chemical to reduce wrinkles. In order to maintain the treated
fabric, the dryer will dry at a lower temperature and the machine will
wash with lessagitation. Recommended article types- Dress shirts/pants,
wrinkle free clothing, poly/cotton blend clothing, table cloths, etc.
Delicate- Select this option for fabrics/articles that are more delicate. In
this setting the drying time will increase and wash at a lower temperature.
Recommended fabric types- Dress shirts/blouses, nylons, sheer or lacy
garments.
EdgeStar Washer/Dryer Combo 12
Hand Wash/Wool: Select this option fo wash the wool textiles labeled with
"Machine Wash" only. If is suggested fo wash only small loads and with
wool-safe detergent. In this cycle the fumble action will agitate less and
will be af a lower spin speed.
Baby Wear- Select this option for baby clothes and people with skin
allergies. The wash cycle will automatically have an extra rinse.
Self-Clean- Run the self-clean regularly fo remove detergent buildup and
other residue from the machine itself. Thissetting will provide extra high
temperature sterilization and help maintain the life and efficiency of this
unit.
NOTE: Do not use this cycle with clothes, and do not add detergent or
fabrics softener.
Rinse & Spin- Select this option to rinse and spin a load separately from a
regular cycle. This can be helpful in preventing fresh stains from setting in
fabrics.
Spin- Select this option to spin a load separately from a regular cycle.
Dry Only Cycles
50 Min Preset- Select this option for a 50 minute timed dry only. The dryer
will automatically lock during this cycle and will remain locked until the
unit reaches a safe temperature.
Cotton/Normal Dry: This cycle will execute a preset 1200 RPM spin speed
and will automatically enter into a drying cycle.
Change Cycles and Options: Not all Options are available with all Cycles.
Cycles and Options can be changed any time before "Start/Pause" is
pressed.
Cancel Wash- To cancel a cycle press [Power] for 3 seconds to stop the
cycle. The door will automatically unlock. Change the cycle by pressing
Start/Pause once and selecting the desired option.
Drain water "manually"- Press"Power" for approximately 3 seconds then
select "Spin" and press and hold "Start/Pause". When the spin is
complete, the door will automatically unlock. Items can then be removed
from the washer.
13
@
LED Display
I
I
I
Add DryTime
[
®
©
Soil Level Indicator-indicates soil level chosen (See Button 10)
Cycle Indicator- Indicates at what stage of the wash/dry cycle machine is in:
_'_ewas,was,_,nse s0,n_'o_
Wash/Cycle Lifecycle Indicator- Reflects time left until end of cycle
Feature Indicator- Indicates features that are active:
- Machine is locked for duration of cycle.
_- Child Lock is on for control panel.
_- Extra Rinse is active
Cycle is active
_"D- Delay Timer is active
Water Temperature- Indicates the selected temperature.
Spin Speed- Indicates the selected spin speed.
Pre-wash- Pressif you want your cycle to include pre-wash.
Temperature- Pressfo increase wafer temperature in increments of ]0 degrees.
EdgeStar Washer/Dryer Combo 14
Spin Speed- Press to increase spin speed time, the washer drum spins at a speed up to
1200RPM. This reduces drying time and saves energy. Press the button until desired
speed is lit, speed increases in increments of 200, 400-1200 rpm. Some fabrics such as
delicates require a slower spin speed.
Soil Level- Pressfo increase time for heavier soiled items. There are three soil levels, each
bar increases the base wash time by five minutes.
Child Lock- Press the soil level and delay buttons of the same time fo unlock
control panel.
Delay Time- Press to set a delay time for when you want the wash to begin. The delay
start light will flash fo indicate the delay time. Ifwill start the cycle after Cxx)hours.
Hour Glass- Indicates time shown is estimated cycle time remaining.
Custom Cycle- After you have modified a wash cycle to your preference hold down this
button. This cycle will be remembered. You can quickly choose this cycle af the time of
your next wash. You can override by holding down the button after a different cycle
and set of options is selected.
Clock- Indicates estimate time left until end of wash/dry cycle.
Extra Rinse- Press button fo add an extra rinse cycle fo the selected cycle.
Add Dry Time- Press button fo add an extra dry time in increments of fen minutes fo your
selected cycle.
15
Tips before Washing
Check for colorfastness.
Before washing any new garment you should always check to see if the
color will bleed to avoid damaging other items in the same wash cycle.
Checking for colorfastness is easy. Simply wet one corner of the fabric
and let it set for a few minutes. Get a white cloth and press down on the
wet part of the garment/item. If any color comes off onto the white cloth,
you know the item is not colorfast and will run in the wash cycle. This
garment/item should be washed separately.
Certain clothes should not be washed in washer:
These include embossed, resins, furs, fur decorations, clothes that easily
wrinkle such as silk, clothes with decorations, handmade items, and
fabrics fhaf discolor easily. Never wash clothes fhaf are stained with
chemicals such as gasoline, petroleum, benzene, paint thinner and
alcohol. These items should be hand washed first. Waterproof items
should not be washed such as car covers, ski suits, outside tablecloths,
etc.
the unit. Proper loading
is I/2 to 2/3 fill with
similar items for most
I OTE: Do not overload 1
effective performance.
Please
Keep in Mind:
pay attention with regard to detergents
Low sudsing detergent or washing powder specially formulated for
front loading machines should be used according fo fiber types
(cotton, synthetic fiber, soft products and wool products), colors,
washing temperatures, degree of soil and types. Otherwise,
excessive bubbles may be generated and overflow from the unit.
Bleach can be harmful and damage clothes, so if is suggested fo
use as little as possible.
Powder detergents can leave residues in the clothes and
generate a smell. If using powder detergent an extra rinse is
recommended.
If there is too much detergent or wafer temperature is too low,
detergent does not easily dissolve completely. Make sure fo follow
the recommended amount fo avoid not rinsing properly from
clothes and unit.
Washing will depend on the weight of clothes, degree of soil level,
local wafer hardness as well as the recommendations from the
detergent manufacturers. Please consult the wafer company if
you are not clear on your wafer hardness.
• Once a cycle is loaded it should not be left for a long period of
time in order fo avoid a moldy smell or causing stains fo set in.
Clothes should be washed in a timely manner for best care.
• Make sure clothes are washed according fo the stated washing
temperature fo avoid color change/distortion.
• Keep detergents and additives in safe dry places out of reach
from children.
• Only use detergents recommended for front loading, and do not
use regular soap as the residue can remain in clothing after wash.
• Please fake items out of your clothes pockets. Please check the
pockets of the clothes fo be washed, remove any loose items fo
avoid possible damage or unnecessary service call.
EdgeStar Washer/Dryer Combo 16
f
NOTE: It is normal if you
clothes feel slightly
damp to the touch
even though they are
dry. This is entirely
normal in the self-
condensing drying
process. All you have to
do is just shake them
out a little bit to allow
any residual humidity to
dissipate (it takes only a
few seconds). Then you
can fold or hang them
as normally.
• Secure fasfeners, zips should be zipped close and buffons or hooks
should be fasfened. Any loose ribbons or lies should be fled
fogefher.
• Clofhes should always be washed/separated according fo fhe
following characferisfics- fabric Type, color, size, and sensifivify.
Always wash according fo label insfrucfions.
• Clofhes wifh butfons, embroideries, or fraying should be fumed
inside out before being washed.
• Remove all pins/hooks from arficle of clofhing before being
washed.
• It is recommended fo put bras wifh wire hooks in sealed pillowcase
fo prevenf sfeel wire from bra popping out of bra and info drum
causing possible damage.
• Delicate's such (mslace, nylons, handkerchiefs, lies, efc. should be
washed in a mesh bag fo avoid damage.
• In order fo gel fhe mosf effecfive wash, clean away dusfs, sfains
and per hair from fhe clofhes prior fo loading.
• To profecf baby's skin, baby arficles should be washed separately
from adutf clofhes. Babywear cycle fhe rinsing is longer in order fo
fhoroughly rinse out defergenf as fheir skin is much more sensifive.
• For parrs of clofhes fhat are more easily sfained if is recommended
fo prefreat before wash in order fo achieve mosf ideal washing
effecf.
17
Washing/Drying Capacity:
Do nor overload fhe unif; otherwise if may diminish fhe washing effecfs. Please
confirm fhe maximum affordable washing quantify according fo fhe following
fable.
Cotton t 5 Ibs 7 ]/2 Ibs
Artifica[ Fibers 8 [bs 4 ibs
Woot 5 1/2 ibs 2 3/4 ibs
DO NOT WASH ANY SINGLE LARGE ITEM AS IT WILL DAMAGE UNIT.
Incorrecf Ioadincl:
Correcf Loadin,q (1/2 fo 2/3 Fill)"
EdgeStar Washer/Dryer Combo 18
OPERATING THE WASHER
Before washing clothes for the first time, the washing machine should be
run through a full cycle with detergent without articles of clothing.
Once you have loaded the washer and added laundry products, you are
now ready to wash!
Start up washing machine
©
Make sure the unit isconnected to power and ensure water lines are
connected properly; the tap should be opened completely. Place your
already sorted wash load into the drum.
Press the "Power" button. The control panel will illuminate.
Turn the cycle selector knob to the desired cycle based on load. The LED
displaypanel will reflect the preset features for fhaf cycle.
// _s 0 ",
/%3 .........,_¢
X,¢_...........,-/
If you would like to modify any of the preset settings for the chosen cycle
press on the individual options until display panel reftecfs desired settings.
Available Options:
Pre-Wash Delay
Temperature Add Dry Time
Spin Speed Extra Rinse
Soil Level Custom Cycle
%
19
Note:
If you have a favorite cycle, once you modify all settings click on "custom
cycle" fo remember for future cycles. Depending on cycle not all options
are available.
Press the start/pause button to begin cycle. Once cycle begins the door
will automatically lock and wash will begin. Display panel will change fo
reflect estimated time and stage of wash. Af any time you can pause the
cycle by pressing on the start/pause button again.
CYCLEGUIDE
This guide _l_w_ you _heo_tkms and I
prese_ optl@ns f_r _'@_@mmended J
Falbric types fgr ead_ yde j
@ i_<Ji_a_,,_,ifo/xior,is |
available F_>_jae_;f_c_yde /
| o#_on {s tvtilable and at) t@|
DDfWa_l'lit@/_ I rl/t:)_af<_d |
Spin Speed 'ihe i_r_S_ /
f_mP/pfts _f:Jeedis bo!d_d |
!
/
/
W
Cycle Guide
1O0 _F
90 F
i_Jp(::old
1O0 _F
I_00 i
600
40{i
Delk_te
HamdW_'_sh/ tap Cold @_
VV_ol
Babywt÷_r _0 °F _OtX:_
W_s _ 60O
9'0_f 600
Tap ¢ott 4_0
NO Spin
N_ gpi_
i (_ F 1200
l'ip Cold 80_
4OO
N_ Spin
_0 °F I OOO
400
Na S_in
elf Gea_
i 7S _F @0
S8 Min
P_eset
Dry #_ede 8d}
_'imSpin
EdgeStar Washer/Dryer Combo 20
CARE AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, fop
performance, and long life and is recommended.
Disconnect plug from outlet and close wafer tap before performing any
cleaning/maintenance fo your combo washer/dryer.
Cleaning the exterior of the unit
Never use solvent based, abrasive cleaners, harsh chemicals or steel wool fo
clean your unit as they can damage the finish. The cabinet and chrome door
may be cleaned with a mild detergent and lukewarm wafer solution such as 2
tablespoons of baking soda to ] quart of wafer. Use a soft sponge and rinse with
clean wafer. Wipe with a soft clean towel fo prevent wafer spotting.
During daily use if isrecommended to wipe up any spills with dry soft cloth.
Cleaning the interior of the unit
Never use solvent based, abrasive cleaners, harsh chemicals or steel wool to
clean the internal drum. During daily use, use a soft cloth to wipe around the
door, opening, and rubber seal to remove any excess moisture and to maintain a
water tight seal.
To clean the inferior of the unit all clothes must be removed from the drum. Select
the cycle "Self Clean", you can either use liquid chlorine or power/fabler tub
cleaners manufactured for this purpose can be used.
For liquid chlorine add directly fo the fabric softener section. For powder tub
cleaner add directly fo the main detergent section. Lastly for fabler add directly
fo the wash drum. Press start fo initiate "Self Clean" cycle.
After every wash clothes should always be removed to avoid odor and/or mildew
from forming.
Cleaning detergent dispenser
Never use solvent based, abrasive cleaners, harsh chemicals or steel wool.
1. Remove the detergent dispenser from the unit by pressing on the
release tab and pull out drawer.
2. Once dispenser drawer is removed remove cap from the fabric
softener compartment (pictured below).
3. Place drawer under warm tap water and dry with soft cloth.
4. Place cap back onto fabric softener and insert dispenser drawer
back into the unit.
21
Clean inlet filter
If tap is fully opened and there is an insufficient amount of water coming
through the hose you may need fo clean your Inlet filter.
Wall Connection
1. Close the tap entirely before cleaning.
2. Select any procedure on control knob and press the "Start/Pause"
button and let run for about 40 seconds.
3. Remove the inlet pipe from tap which is connected on the wall.
4. Run warm wafer fo run through filter and reconnect inlet pipe fo
hose.
Unit Connection
1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long nose pliers and wash under warm wafer.
3. Reconnect the inlet pipe
4. Open the tap and make sure there is no wafer leakage.
Notes: Generally, the tap filter should be washed first and then the filter fo
the washing machine.
Remove foreign matters from Coin Trap
Coin Trap can collect small objects from the wash cycle. Clean out the
coin trap regularly fo ensure normal operation of washing machine.
Step 1: Open coin trap
door
Step 3: Pull out coin trap
and remove articles
Step 2: Turn knob
clockwise
Step 4: Place drain pan
under for excess water
EdgeStar Washer/Dryer Combo 22
TROUBLESHOOTING TIPS
Before Calling for Service
If the unit appears to be malfunctioning, the issue could be solved by
following the suggestions in the "Solution" column.
Issue
Washing
Mqchine wi_}
no_ start -D
POOl CannOt
be openea
Wa_er leakage
Waler is leaking
flora me
botlom o! the
machine
Indiee_for or
display aces
not lighl
Detergem
residues in the
detergent
disoensel
Unsafistactot
washing effects
Abnormal
FiOiS@
excessive
v_brahor
Possible Cause
Machine's safety
ptotechor desig, is
working. The door bcK m
enggagea
BITC {temperature
sensorj m damaged and
heating p_pe is aging,
Tl;_econr, echons are not
fiqht Drair o_oe is
BlOCked.
The inlet aide _sno1
connected firmM Outlet
h@se has wate_ tankage
O! Ioo&e barge ir L_flit.
Power is disconnectea
Washing oawfs_ m
dampened ann _
clumped _ogether.
The c_omes are 1co did _,,
overtoadedo Water
Te_'lD@foture 1%_oc cold
Solution _
Ensure the door _sdosed fighfIy
Che_k _fpower plug i_ inseded web
Check rc make sure the elec_ncal culler has Dower
Check it water supply _ao is ooenea.
Check :f "Power' [)uHon B pressea,
Check # %tad/Pause" button is oressea.
Disconnec_ Power
Allow unit to coo/to safe tem_st-xa_ure,
Can NOHT'_Q_/Vwash the clothes orw cannot wash
with nearing. Contact authorized teclY'_id_sn
Check and fasten water pipes
C_ean drain obe
Contocl authorized _echn_c_c_n
F_×the _ntet oiE,e.
Replace me drain hose.
Contact _-tufhodzed techniciar
Check if the power is shut off and cower plug s
connected cerrec1/y f no1 ole¢_se cor'dac!
authorized technician,
ThOrOUgh@ c_e_f_ rne dete_gen_ dispense_ a_d d_Y
with c_om use H_gh Efficiency _au_a detergen_
specially _o_front _oading machines_
MaRe sure ¢ou have selected 1he olooer
orocedure _wa_er _emperature aCCOrding to fabric
type and washing label Add fne proper detergent
auantifv according _o ff"_e ins_ruc tions on detergen_
packaging, _ is recommended to use High_
Efficienc_ aeterger4.
Check to make sure the transportation °'shipping"
bo_ts have Dtc peny oeen _movea.
Ensure the c_nitis _nstaIIed on a sand and/eve floor
Check to make sure there are no bose articles left
;n the drum.
blake :sure leg_ are _rc pedy adius_ea.
Ensure unH _sr_ot oweftoaded
23
TROUBLESHOOTING TIPS CONTINUED...
Sobtton
Door lock Doo_ s nor ch:)sed property.
problem Piease call on ouihodzed techn c an f probtem pennis1
T_p is no_ opened ,a_i the Open Hse tap Iu!iy oi we]_ fo_ 1he
Wa_e_ inferject_ng w®y wa_et flows fOos!Ow_y wofer suppy becomes ro_mal.
issue when Iniel volve fiiie_ s becked Checkinet valve filie S_raghtes
;w®sh]n9 bv®'ler inie_ pip:e may be iwis ed f €he wafe_ hoses fo ensure fhe_e
in:te!'ieciin9 _ha{ w®iel s no_ st_pptied are no iwisfs
exceeds 5 rains}
Peose ca_ian autho_zed technc:i®n if ptobem persisis.
Please Ca!ion authorized eehn_c4on e aiiothe_ issues
Resfa_ o_ter _he doo_ ischased.
Care Label Appendix
GraphicSy_bot Hlustratien I/luslration
Hand Wash No Machine Wash
Washing d_cbdi_g Machine Oe no[ Wash
Wash and Hand Wash
No D_v Clean
Dry Clean
Warm y Dry Clean )_ _
Bleach
Tumble dry Do not _ron
No Wn,sg
No Bleach
De not Tumble DIh,
Iron _::_ _ror,w_nCloth
Steamiron
Medium Temeerature and Dry after Wash
Max, Temoe_ra_wet 50C
t._ Jne D[_ in Shade
EdgeStar Washer/Dryer Combo 24
SPECIFICATIONS
Description of product
Model
Voltage/Frequency
Rated Current
Color
Washing Capacity/
Dry Capacity
Drum Size
Standard Water Pressure
Weight
Combo Washer/Dryer
CWD1510W
AC 115V-60Hz
12A
White cabinet with chrome door
15 Ibs. / 7.7 Ibs.
2.0 cu. ft.
0.05MPa-1MPa
165 Ibs.
Note: Technical data and performance information provided for
reference only.
Specifications are subject to change. Check the rating label on the ice
maker for the most accurate information.
25
This product is warranted by EdgeSfar and is subject fo any conditions set forth as follows:
WHAT IS COVERED:
For a period of ONE (1) YEAR from the date of
original retail purchase, EdgeSfar will repair or
replace any part free of charge including labor
that fails due fo a defect in materials or
workmanship. Labor will be performed free of
charge at an authorized EdgeStar repair facility
and EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may
request a defective part be returned in
exchange for the replacement part. All
replacement pads or products will be new,
remanufacfured, or refurbished. All products and
parts replaced by EdgeStar under warranty
service become the property of EdgeStar. After
the 12 month period, EdgeStar will no longer be
responsible for labor charges incurred or
replacement parts. All defective products and
parts covered by this warranty will be repaired or
replaced on a mail-in basis fo an EdgeSfar
authorized repair facility.
This warranty applies to the original purchaser
only, and only covers defects in workmanship
experienced during operation of the product
under normal service, maintenance, and usage
conditions. This warranty applies to the purchase
and use of this product in residential settings
within the United States of America.
Exceptions: Commercial or Rental Use
Warranty
90 days labor and parts from date of original
purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the
coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup or training to use the
product.
-Shipping damage, and any damage caused by improper
packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and fear on parts or replacement of parts designed
fo be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or fo
instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse,
operation outside environmental specifications, uses contrary to
instructions provided in the owner's manual, accidents, acts of
God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or
modification, or commercial use.
-Labor, service transportation, and shipping charges for the
removal and replacement of defective parts, beyond the initial ] 2
month period.
-Products that have been modified to perform outside of
specifications without the prior written permission of EdgeSfar.
-Products lost in shipment, or theft.
-Products sold AS ISor from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced,
or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring
or plumbing.
-Damage fo personal property from use of product.
-Damage from service other than from an authorized EdgeStar
repair facility.
-Hoses, knobs, lint frays and all attachments, accessories and
disposable parts.
-Any service charges not specifically identified as normal such as
normal service area or hours.
-Any special or consequential damages arising out of the use of
the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edqestar.com or call 1-866-319-5473. Before contacting
Customer Support you are required fo have your model number, serial number and proof of purchase available upon
request. Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for
damage resulting from shipper mishandling or improper packaging. Do not return a defective product fo the place of
purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSOR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESSWARRANTY
PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN
CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
Reassembly of the coin trap/lint trap component of the EdgeStar Washer Dryers
If the end piece of the coin trap component on EdgeStar combination washer dryers is
fully unscrewed, the component can come completely apart. Here is how you re-assemble
it
t.
Start with the pieces shown in the order below.
2. Put the rubber gasket onto the end of the Ion _iece, as show below.
.
Put the white piece
as shown below.
4, Lightly screw the remaining piece onto the assembly, as shown below.
5. Now the component is reassembled and can be reinserted (and then tightened)
into the combo.
Note: here is another view of the correct order and _lacement of the component parts:
To use, simply hook up the faucet adapter to your faucet and connect the y connector to the faucet adapter ]
and water inlet hoses. The casters included in this kit replace the leveling legs on the washer dryer I
ISimplv replace the leveling legs on the unit with these locking casters I
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
@
Register your product, download owner's manuals, access additional
troubleshooting resources, and obtain more information on other
great EdgeStar products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2011 Living Direct, Inc. All rights reserved.
Loading...