© 2009 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
M-SPI-_
M2- -_SPI
FJ- -_SPI
904- -03SPIRIT
Installation Instructions for
Spirit 3", 6", & 12"
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Use this fixture indoors only.
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations.
- This product is not restricted to certain height installation.
It is approved to be used at any height above the floor.
- Applicable accessories are Hexcell Louver, Glass Lenses,
Little Shady Mesh Back Shade, Little Shady Round Back
Solid Shade, Little Shady Round Back Glass Shade, Large
Solid Back Shade.
SAVE THESE INSTRUCTIONS!
Install the Lamp & Accessory Shade (S3-_)
A
CAP
1
ACCESSORY SHADE BASE
Use MAX 50 Watt, Type MR16 Front Glass Cover Halogen
Lamp.
2: Place the MR16 lamp into the accessory shade.
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
1: Unscrew and remove the cap from the accessory shade base
(this only applies for Little Shady round back glass shade
accessory).
B
ACCESSORY SHADE
2
MR16 LAMP
1
C
MR16 LAMP
SLOTTED
SHADE HOLDER
3: Line up the MR16 lamp pins with the socket holes.
4: Push the lamp pins completely into the socket holes and
simultaneously push the accessory shade onto the slotted
shade holder.
D
4
ACCESSORY SHADE
5: The accessory shade must fit snugly onto the slotted shade
holder. If adjustment is necessary, carefully bend the slotted
shade holder tabs slightly in or out with needle-nose pliers.
E
CAP
6
TAB
NEEDLE-NOSE PLIERS
5
6: Place the optional glass lens or hexcell louver accessory into
the cap (this only applies for Little Shady round back glass
shade accessory).
7: Screw the cap completely to the accessory shade base (this
only applies for Little Shady round back glass shade
accessory).
F
GLASS LENS OR
7
HEXCELL LOUVER
8: OPTIONAL: To position the handle in a different angle turn
the plastic portion of the handle clockwise until desired
position is achieved.
HANDLE
8
2
Install the Fixture to Monorail Connector (MC-FJ-_)
FAST JACK
G
HOUSING
MONORAIL
1
1: Place the Fast Jack housing onto the Monorail and use
fingers to tighten the Fast Jack housing connector to the Fast
Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into the
Fast Jack housing connector.
2
FAST JACK HOUSING
CONNECTOR
FAST JACK
2
FIXTURE
CONNECTOR
Install the Fixture to Monorail
2 Circuit Connector (M2C-FJ-_)
1: Place the Fast Jack housing onto the Monorail 2 Circuit and
use fingers to tighten the Fast Jack housing connector to the
Fast Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack housing connector.
CIRCUIT #1 CIRCUIT #2
I
0.05 ALLEN
WRENCH
3
#4-40 SET
SCREW
1
2
N
4
1
2
N
FAST JACK
H
HOUSING
1
FAST JACK HOUSING
CONNECTOR
3: To power the fixture from circuit #1, top and bottom
(neutral) rails, tighten the #4-40 set screw on top of the
housing with the 0.05 Allen wrench. Make sure this set
screw connection is very tight.
4: To power the fixture from circuit #2, middle and bottom
(neutral) rails, remove the #4-40 set screw from top of the
housing and tighten it into the side threaded hole with the
0.05 Allen wrench. Make sure this set screw connection
is very tight.
To avoid shorting the system, do not use more than one
NOTE:
set screw to select a circuit on the Monorail 2 Circuit connector.
MONORAIL 2 CIRCUIT
FAST JACK
2
FIXTURE
CONNECTOR
2
Install the Fixture to Fast Jack
Canopy (FJP-2SQ-_, FJP-4SQ-_,
FJP-4RD-_)
1: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack canopy connector.
NOTE: Do not load either circuit over the maximum system
rating.
J
FAST JACK FIXTURE
CONNECTOR
FAST JACK CANOPY
CONNECTOR
1
1
3
Loading...