Edge Lighting PSB-60W-ELV-12VDC User Manual
904-PSB-60W-ELV-12VDC
© 2012 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
PSB-60W-ELV-12VDC
Installation Instructions for 60 Watt 12 Volt DC Power Supply
GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS
- RISK OF FIRE: This product must be installed by a
qualified electrician. Turn the power to the electrical box off
during installation. Read the "Important Safety Instructions"
before installation.
- Do not install this power supply in a wet location.
- To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
- This product is not suitable for wet locations. It is approved
for the use at any height above the finished floor.
- A typical installation is shown. Specific installation must be
in accordance with the local electrical codes.
- TO REDUCE RISK OF FIRE, it is important to wire the
power supply for the system as described in this
installation instruction.
- Load the power supply to MAXIMUM 60 Watts.
SAVE THESE INSTRUCTIONS!
Install the Power supply
A
POWER
SUPPLY
CASE
2
COVER
1
PHILLIPS
SCREW
- Do not install *LED fixture closer than three inches or as
specified in the *LED fixture installation instructions to
curtains or similarly combustible materials. Keep insulation
at least 3" away from the enclosure.
- Turn the electrical power off before modifying the lighting
system in any way.
- The system is "ETL" listed for USA and Canada only when
all the products used are supplied by Edge Lighting.
- For dimming options refer to EDGELIGHTING.COM.
* See LED fixture installation instructions for proper
placement.
1: Loosen and remove the four Phillips screws on the top &
sides of the power supply case to remove the cover.
2: Secure the power supply case to the desired location with
the four #6 screws provided.
B
3: Install conduits from the electrical box panel and the
dimmer electrical box (if used) to the power supply case.
4: DO NOT connect the power wires to the panel at this time.
5: Ground the power supply housing in accordance with local
electrical codes.
6: Connect the neutral power wire to the white power supply
wire and the wire going to the neutral of the dimmer with a
wire nut.
7a: In case of not dimming, connect the hot power wire to the
black and brown power supply wire and to the hot switch
leg wire with a wire nut (not shown). Refer to the wiring
diagram on page 2.
7b: In case of dimming, connect the hot power wire to the
black power supply wire and the wire connecting to the
dimmer hot wire with a wire nut. Connect the brown power
supply wire to the switch leg hot wire coming from the
dimmer with a wire nut. Refer to the wiring diagram on
page 2.
CONDUIT
POWER SUPPLY
5
7b
CONDUIT
3
7b
6
1
C
POWER SUPPLY
10
12V DC-
NOTE: In order to use small gauge wires from the power
supply to the Soft Strip, it is recommended to install the power
supply as near as possible to the LED fixture. See "Low Voltage
Wire Size Chart" on page below.
8: Use the "Low Voltage Wire Size Chart" below to determine
the proper wire size connecting the power supply wires to
the LED soft strip wires.
9
12V DC+
8
NOTE: Maximum length of a single soft strip to be connected to
the power supply is 32' for SS1 and 25' for SS3 & SS2P.
Maximum total load is 60 watts.
NOTE: Use only 12 volt LED soft strip with this power supply.
9: Connect the LED soft strip red wire into the power supply
"+V" terminal.
LED SOFT STRIP
11: Replace the power supply cover and tighten the four
Phillips screws on top & sides of the cover.
12: Connect the 120 volt power wires at the panel.
13: Turn on the power.
E
TERMINAL
14
POWER SUPPLY
DIMMING
POTENTIOMETER HOLE
Wiring Diagram
DIMMING WIRING
10: Connect the LED soft strip black wire into the power supply
"-V" terminal.
D
POWER
SUPPLY CASE
11
11
PHILLIPS
SCREW
COVER
14: In case of dimming, if the soft strip flickers when the
dimmer is at the low light level, then the dimming
potentiometer needs to be adjusted. While facing the low
voltage terminals, remove the round sticker on right side of
the power supply to expose the potentiometer. Carefully
using a #0 Phillips head screw driver (do not push the
screwdriver too much inside the hole which will cause the
potentiometer to bend) rotate the potentiometer to
increase the light level until the light stops flickering.
Replace the sticker.
HOT 120V AC
120VAC
NEUTRAL 120V AC
ON/OFF WIRING
HOT 120V AC
120VAC
NEUTRAL 120V AC
YELLOW
(SWITCH LEG)
HOT
GREEN
BROWN
BLACK
WHITE
GREEN
BROWN
BLACK
WHITE
POWER SUPPLY
PSB-60W-ELV-12VDC
60W
POWER SUPPLY
PSB-60W-ELV-12VDC
60W
LOW VOLTAGE WIRE SIZE CHART
TRANSFORMER
WATTAGE
WIRE SIZE
FOR UP TO 4 FT
60 WATT #18 GA #16 GA #14 GA #12 GA
WIRE SIZE
FOR 5-6 FT
WIRE SIZE
FOR 7-13 FT
WIRE SIZE
FOR 14-20 FT
RED +
BLACK -
RED +
BLACK -
SOFT STRIP
12VDC
SOFT STRIP
12VDC
WIRE SIZE
FOR 21-34 FT
#10 GA #8 GA
WIRE SIZE
FOR 35-52 FT
2
Loading...