Edge Lighting PSB-100W-24VDC-RGB User Manual
PSB-100-24VDC-RGB-02
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2014 Edge Lighting. All Rights Reserved.
Installation Instructions for 100 Watt 24 Volt DC RGB DMX
LED Power Supply
SAVE THESE INSTRUCTIONS!
GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS
- RISK OF FIRE: This product must be installed by a
qualified electrician. Turn the power to the electrical box off
during installation. Read the "Important Safety Instructions "
before installation.
- Do not install this power supply in a wet location.
- To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
- This product is not suitable for wet locations. It is approved
for the use at any height above the finished floor.
- A typical installation is shown. Specific installation must be
in accordance with the local electrical codes.
- TO REDUCE RISK OF FIRE, it is important to wire the
power supply for the system as described in this
installation instruction.
- Load the power supply to MAXIMUM 100 Watts.
- Use CDP color dial or CTP color touch screen controller with
RGB LED soft strip.
100W, 24VAC LOW VOLTAGE WIRE SIZE CHART
3%
VOLTAGE
DROP
WIRE LENGTH
IN FT
WIRE SIZE
VOLTAGE AT END
OF THE WIRE
UP TO 31FT
14 AWG
23.28 VAC
- Do not install *LED fixture closer than three inches or as
specified in the *LED fixture installation instructions to
curtains or similarly combustible materials. Keep insulation
at least 3" away from the enclosure.
- Turn the electrical power off before modifying the lighting
system in any way.
- The system is "ETL" listed for USA and Canada only when
all the products used are supplied by Edge Lighting.
* See LED fixture installation instructions for proper
placement.
32FT-49FT
12 AWG
23.29 VAC
50FT-81FT 82FT-124FT
10 AWG 8 AWG
23.28 VAC 23.28 VAC
1
Using LED Power Supply with RGB Soft Strip & CDP or CTP
Controller
A
COVER
PHILLIPS SCREW
1
M
COVER
M
POWER SUPPLY
CASE
DVR-RGB-60
2
NOTE: Use a deep double gang boxes to fit the controller
and controller power supply (OT-20-120-240-245
recommended).
1: Loosen the six Phillips screws on front of the power supply to
remove the cover.
2: Carefully pull off the cover from the DVR-RGB-60 driver.
B
CONTROLLER
CONTROLLER
POWER SUPPLY
NOTE: Refer to the "Configuring DimWheel" & "Operating
DimWheel" on page 6 & 7 to properly operate the controller.
3: Connect one end of a red wire to "VDC+" of the controller
terminal and the other end of the red wire to the "+24VDC"
of the power supply terminal.
4: Connect one end of a black wire to "Ground" of the controller
terminal and the other end to the "-24VDC" of the power
supply terminal.
5: Run the black and white line voltage wires coming from
the controller power supply to the power supply case.
6: Connect the white wire to "N" terminal of the controller
power supply.
7: Connect the black wire to "L" terminal of the controller
power supply.
8: Install conduits from controller, main panel (line voltage),
and soft strip to power supply.
9: Run proper DMX cable (Belden #9841 recommended)
with three data wires from controller to the power supply
box.
CONDUIT
ELECTRICAL BOX
5
9
8
7
6
4
3
DMX CABLE (BELDEN #9841)
M
POWER SUPPLY
2
Loading...