Edge Lighting Plaza Small Dimmable User Manual

© 2012 Edge Lighting. All Rights Reserved.

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]
www.edgelighting.com
[e-mail]

PLAZA-S-F1D-_

Installation Instructions for Plaza Small Dimmable

IMPORTANT INFORMATION

- This product is ETL listed for indoor dry locations.

- This product is wall mounted only.

- Supply power to mirror in accordance with local electrical
codes.

- This instruction shows a typical installation

- This product is dimmable with 0-10V dimmers.

SAVE THESE INSTRUCTIONS!

Install the Fixture

904-PLAZA-S-F1D-01

A

POWER WIRE

ELECTRICAL BOX

#8-32 SCREW

1

CROSSBAR ASSEMBLY

2

1: Feed the power wires through the crossbar assembly center

hole.
2: Mount the crossbar assembly to the electrical box holes with

the provided #8-32 screws.

2

B

4

4

CROSSBAR ASSEMBLY

GNL

GNL

3

MOUNTING PLATE

4

4

3: Align the mounting plate center hole with the crossbar

assembly nipple and slide onto the nipple.
4: Level the mounting plate horizontally and mark the six

mounting plate holes onto the wall. These points are for the
anchors.

5: Remove the mounting plate.

4

4

1

9/32 DRILL BIT

C

WALL

ANCHOR

6: Use a 9/32 drill bit to make holes on all six marked points.
7: Tap the anchors into the drilled holes with a hammer.

6

7

7

8: Feed the power wires through the mounting plate center

hole and slide the mounting plate onto the nipple.
9: Secure the mounting plate to the crossbar assembly by

tightening the nut and lock washer. Make sure that the
mounting plate holes line up with the anchors.

D

GNL

GNL

8

LOCK WASHER

9

NIPPLE

NUT

E

#8 SCREW

MOUNTING
PLATE

10: Level the mounting bracket horizontally and use the #8
screws to secure the mounting plate to the anchors.

10

GNL

GNL

2

F

10: Connect the hot, neutral power wires into the wago

connector.

GNL

GNL

10

MOUNTING
PLATE

BALLAST

12

VIOLET

GRAY

GREEN
WHITE
BLACK

11

(+) Dimming
(-) Control

G
N
L

WAGO
CONNECTOR

TAB

10

GNL

GNL

CAUTION: To reduce risk of a burn or electrical shock during

lamping, disconnect the power to the fixture.

NOTE: If necessary, push the tab down and then pull the Wago
connector for a quick disconnect.

NOTE: Omit steps 11 & 12 for non-dimming wiring.

11: For dimming, run the violet and gray wires from the

dimmer to each ballast. The wires must be solid copper
(refer to the dimmer instruction for more details).

12: Branch the violet wire to the (+) & the gray wire (-)
terminals of each ballast respectively.

G

SPRING CLIP

13

13

GNL

GNL

Use MAX 55 Watt Type 2G11 Base
Compact Fluorescent Lamp For Each Socket.

13: Push the lamp pins completely into the socket holes and
secure by snapping into the spring clips. Repeat this step
for the remaining sockets.

NOTE: NEMA fluorescent lamp manufacturers recommend to

reduce possible flicker or instability when new dimming systems
are commissioned, lamps should be operated at the ballast's
maximum light output setting overnight (approximately
12 hours).

H

THUMB SCREW

GNL

GNL

MOUNTING PLATE

14

13

SOCKET

LAMP

13

14: Place the mirror housing into the mounting plate and

secure it in place by tightening the two thumb screws from
the top and bottom of the mounting plate into the mirror
housing.

MIRROR HOUSING

14

3