Edge Lighting Mata Hari 3 User Manual

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]

www.edgelighting.com

© 2011 Edge Lighting. All Rights Reserved.

[e-mail]

Installation Instructions for Mata Hari 3

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:

- Use this fixture indoors only.

- Do not look directly at the lamp while the fixture is on.

- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.

- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.

- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.

- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.

- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.

- It is normal for a new halogen lamp to produce minor
smoke when first turned on.

- Do not operate the luminaire with a missing or damaged
shield.

- Turn power off and allow to cool before replacing lamp.

FJ-MATA3-_

904-FJ-MATA3-01

IMPORTANT INFORMATION

- This product is ETL listed for indoor dry locations and
approved to be used at any height above the finished
floor.

SAVE THESE INSTRUCTIONS!

Adjust the Fixture Height

A

H

1: Cut the coaxial cable to the desired height (H) with a sharp
cutter. The overall fixture height is measured from the
bottom of the glass shade to the end of the coaxial cable.

1

112

B

STRAIN RELIEF TUBE

2

2: Feed the coaxial cable through the conical nipple and flared

side of the strain relief tube. Slide the conical nipple and
strain relief tube down the coaxial cable.

CONICAL NIPPLE

3: Feed the coaxial cable into the coaxial fixture connector. The
coaxial cable will come to a stop point.

COAXIAL CABLE

D

1.5MM ALLEN WRENCH

M3 SET SCREW

WRINKLE

5

4

C

3

COAXIAL CABLE

4: Keep feeding the coaxial cable in until the inner wire is
visible in the screw hole of the fixture connector tip. The
outer metal jacket will start to wrinkle.

5: Hold the fixture connector in place. Replace and tighten the
M3 set screw on fixture connector tip with the 1.5mm Allen
wrench.

6: Pull down the outer metal jacket to smooth the wrinkles.

6

OUTER METAL JACK INNER WIRE

7: Push the strain relief tube completely into the coaxial
fixture connector. Make sure the slot on the strain relief
tube is not inline with the M4 set screw.

8: Tighten the M4 set screw with the 2mm Allen wrench.

E

2MM ALLEN WRENCH

M4 SET SCREW

COAXIAL FIXTURE
CONNECTOR

8

7

STRAIN RELIEF TUBE

F

9: Use fingers to tighten the Fast Jack fixture connector into

the Fast Jack system connector (Monorail, Monorail 2

9

Circuit, or canopy connector - Refer to the instructions
provided with the system connector or canopy).

9

9

9

CIRCUIT #1

10

1

9

9

2
N

10: Refer to the instructions provided with the Monorail 2

Circuit fixture connector to choose Circuit #1 or Circuit #2.

CIRCUIT #2

10

1
2
N

Install the Lamp

CAUTION: To reduce risk of a burn or electrical shock during

lamping, disconnect the power to the fixture.

Use MAX 50 Watt, Type MR16 Front Glass Cover
Halogen Lamp.

1: Lift the metal cloth shade up to expose the socket.

2: Push the lamp pins completely into the socket holes.

G

METAL CLOTH
SHADE

1

SOCKET

2

LAMP

3