Edge Lighting Low Rider Spinner User Manual
© 2009 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
M-LOS-_
M2-LOS-_
FJ-LOS-_
904-SPINNER-04
Installation Instructions for
Low Rider Spinner
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
– Use this fixture indoors only.
– Do not look directly at the lamp while the fixture is on.
– RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
– Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
– Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
– Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth. Oil from skin
may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations.
- This product is not restricted to certain height installation.
It is approved to be used at any height above the floor.
- Required shades are Divi,Tapered, or Nico 3.
- Applicable optical accessories Hexcell Louver, or Glass
Lenses.
SAVE THESE INSTRUCTIONS!
Install the Lamp & Shade
A
THREADED SOCKET HOUSING
KNURLED NUT
1
2: Carefully slide the shade onto the threaded socket housing
and secure it by tightening the knurled nut.
Use MAX 50 Watt IR, Type MR16 Front Glass Cover
Halogen Lamp.
Use MAX 6 Watt LED MR16 Lamp.
CAUTION:
lamping, disconnect the power to the fixture.
1: Loosen and remove the knurled nut from the threaded
socket housing.
B
To reduce risk of a burn or electrical shock during
THREADED SOCKET HOUSING
3
2
3
KNURLED NUT
SHADE
LAMP
3: Align and push the lamp pins completely into the socket
holes.
1
Install the Fixture to Monorail Connector (MC-FJ-_)
FAST JACK
C
HOUSING
MONORAIL
1
1: Place the Fast Jack housing onto the Monorail and use
fingers to tighten the Fast Jack housing connector to the Fast
Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into the
Fast Jack housing connector.
2
FAST JACK HOUSING
CONNECTOR
FAST JACK
2
FIXTURE
CONNECTOR
Install the Fixture to Monorail
2 Circuit Connector (M2C-FJ-_)
1: Place the Fast Jack housing onto the Monorail 2 Circuit and
use fingers to tighten the Fast Jack housing connector to the
Fast Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack housing connector.
CIRCUIT #1 CIRCUIT #2
E
0.05 ALLEN
WRENCH
3
#4-40 SET
SCREW
1
2
N
4
1
2
N
FAST JACK
D
HOUSING
1
FAST JACK HOUSING
CONNECTOR
3: To power the fixture from circuit #1, top and bottom
(neutral) rails, tighten the #4-40 set screw on top of the
housing with the 0.05 Allen wrench. Make sure this set
screw connection is very tight.
4: To power the fixture from circuit #2, middle and bottom
(neutral) rails, remove the #4-40 set screw from top of the
housing and tighten it into the side threaded hole with the
0.05 Allen wrench. Make sure this set screw connection
is very tight.
To avoid shorting the system, do not use more than one
NOTE:
set screw to select a circuit on the Monorail 2 Circuit connector.
MONORAIL 2 CIRCUIT
2
FAST JACK
FIXTURE
CONNECTOR
2
Install the Fixture to Fast Jack
Canopy (FJP-2SQ-_, FJP-4SQ-_,
FJP-4RD-_)
1: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack canopy connector.
NOTE: Do not load either circuit over the maximum system
rating.
F
FAST JACK FIXTURE
CONNECTOR
FAST JACK CANOPY
CONNECTOR
1
1
2
Loading...