Edge Lighting Light Channel, Millwork 24V User Manual

© 2013 Edge Lighting. All Rights Reserved.

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]
www.edgelighting.com
[e-mail]

LCMW-24V-_

Installation Instructions for Millwork Light Channel, 24VDC

IMPORTANT INFORMATION

- This instruction shows a typical installation.

SAVE THESE INSTRUCTIONS!

Install the Light Channel

904-LCMW-24V-01

A

1 3/8"

FOR

CORD

5/8"
CUT

DEPTH

7/8" CUT

NOTE:

connected together with the flexible connectors. Refer to the
instructions provided with the flexible connectors.

Multiple light channels up to total of 25 feet long can be

CHANNEL

LENGTH

WOOD

MITER CUT

7/8" WIDE

1: Determine the location of the Millwork Light Channel on the
wood.

NOTE:

3/4" thick wood. The cut out slot must be 7/8" wide and 5/8"
deep. Add 1-3/8" to the length of the channel to accommodate
the power cord spacing.

The Millwork Light Channel needs to be installed onto a

B

LIGHT CHANNEL

FLEXIBLE
CONNECTOR

ADDITIONAL
LIGHT CHANNEL

C

SCREW

FLEXIBLE
CONNECTOR

POWER FEED
CONNECTOR

2

DECORATIVE
CAP

3

LIGHT CHANNEL

END CAP

POWER FEED
CONNECTOR

POWER FEED
WIRES

SCREW

NOTE:

female or male end of the channel.

The power feed cable can be mounted to either the

2: Remove the two screws on the bottom of the light channel
(not the screws holding the decorative cap).

3: Place the male end of the power cord in the cord grip if

LIGHT
CHANNEL

connecting to the female end of the light channel, or place
the female end of the power cord in the cord grip if
connecting to the male end of the light channel.

4: Push the cord completely into the light channel power end

4

cap pins and secure the cord grip to the light channel by
tightening the two screws (provided with cord grip) through
the cord grip into the light channel power end cap.

1

D

LIGHT CHANNEL

POWER CORD

5: Cut the other end of the power cord (male or female) and
discard it. Strip the wire end for connecting it to the power
supply.

5

E

7

CUT

5

MOUNTING PLATE

SLOT

6: Drill one end of the slot with 7/32 bit to run the light channel
wire.

7: Feed the wires through the hole and snap the light channel
into the slot, make sure all clips are tight. If necessary slide
the mounting clip to the appropriate area.

8: Follow the instructions provided with the power supply to
power up the light channel.

Replacing the Soft Strip

F

1

REMOVE OLD
SOFT STRIP

2

BACKING

SOFT STRIP

CHANNEL

LIGHT CHANNEL

7

1: Carefully pull existing old Soft Strip completely off the

channel.

2: If there is Soft Strip residue on the channel apply in
moderation WD-40, or Goo Gone, or a mixture of warm
water and lemon oil to the corner of a clean, dry towel.
Gently buff the area containing the adhesive residue with
small circular motion until it is completely removed.

NOTE: Avoid bending the soft strip in sharp vertical angles which
may damage the LEDs. Soft Strips do not bend horizontal. Use
proper directional connectors for horizontal turns.

3: Carefully remove the backing from the new LED soft strip,
make sure not to remove the tape from the soft strip. Firmly
press down the adhesive portion of the soft strip onto the
channel while removing the rest of the backing, making sure
there are no air bubbles that can cause surface irregularities.

GENERAL WIRING DIAGRAM

WHITE (NEUTRAL)

INPUT

120VAC

GND

BLACK (HOT)

RED 120VAC (HOT)

PURPLE 1-10V

GRAY 1-10V

DIMMING

LIGHTOLIER:

ZP600FAM120

CONTROLLER

PSB-96W-010-24VDC

input 120VAC
WH (N)
BK (L)

input 0-10V
PUR
GRY

RED (24VDC+)

BLUE (RETURN-)

YELLOW (DIM RETURN-)

24VDC

RED 24VDC+

BLACK 24VDC-

SURFACE MOUNT
LIGHT CHANNEL

2