1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
© 2012 Edge Lighting. All Rights Reserved.
info@edgelighting.com
Installation Instructions for Izar Pendant
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Use this fixture indoors only.
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
FJ-IZAR-_
904-FJ-IZAR-01
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations and
approved to be used at any height above the finished
floor.
SAVE THESE INSTRUCTIONS!
Adjust the Fixture Height
A
COAXIAL CABLE
GLASS SHADE
1
SOCKET
2: Cut the coaxial cable to the desired height (H) with a sharp
cutter. The overall fixture height is measured from the
bottom of the glass shade to the end of the coaxial cable.
1: Feed the fixture coaxial cable through the glass shade
carefully lower the glass shade down to rest onto the socket.
B
COAXIAL CABLE
H
2
GLASS SHADE
1
1
C
2MM ALLEN
WRENCH
1.5MM ALLEN
WRENCH
3: Loosen the two M4 set screw on base of the coaxial fixture
connector with the 2mm Allen wrench provided. Do not
remove these set screws.
4: Remove the M3 set screw on tip of the connector with the
1.5mm Allen wrench provided.
M4 SET SCREW
COAXIAL FIXTURE CONNECTOR
5: Feed the coaxial cable through the conical nipple and flared
side of the strain relief tube. Slide the conical nipple and
strain relief tube down the coaxial cable.
3
4
M3 SET
SCREW
E
6
D
CONICAL NIPPLE
6: Feed the coaxial cable into the coaxial fixture connector. The
coaxial cable will come to a stop point.
STRAIN RELIEF TUBE
5
COAXIAL CABLE
COAXIAL CABLE
7: Keep feeding the coaxial cable in until the inner wire is
visible in the screw hole of the fixture connector tip. The
outer metal jacket will start to wrinkle.
8: Hold the fixture connector in place. Replace and tighten the
M3 set screw on fixture connector tip with the 1.5mm Allen
wrench.
9: Pull down the outer metal jacket to smooth the wrinkles.
F
1.5MM ALLEN WRENCH
M3 SET SCREW
WRINKLE
9
OUTER METAL JACK
8
7
INNER WIRE
FIXTURE CONNECTOR
2
10: Push the strain relief tube completely into the coaxial
fixture connector. Make sure the slot on the strain relief
tube is not inline with the M4 set screw.
11: Tighten the two M4 set screws with the 2mm Allen wrench.
G
2MM ALLEN WRENCH
M4 SET SCREW
COAXIAL FIXTURE
CONNECTOR
11
10
STRAIN RELIEF TUBE
H
12
12
12
12
CIRCUIT #1
12
13
12
12: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack system connector (Monorail, Monorail Wall,
Monorail 2 Circuit, or multi-port and mono-point canopies.
Refer to the instructions provided with the system
12
connector or canopy).
13: Refer to the instructions provided with the Monorail 2
Circuit fixture connector to choose the Circuit #1 or Circuit
#2.
CIRCUIT #2
1
2
N
13
1
2
N
3
Install the Lamp
I
GLASS
SHADE
SOCKET
1
LAMP
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
Use MAX 20 Watt, Type MR11 Front Glass Cover
Halogen Lamp.
1: Lift glass shade up to expose the socket.
2: Push the lamp pins completely into the socket holes.
3: Carefully lower the glass shade down one at a time.
3
2
4
Loading...