Edge Lighting Harley User Manual

© 2009 Edge Lighting. All Rights Reserved.

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]
www.edgelighting.com
[e-mail]

M-HAR-4_

M2-HAR-4_

FJ-HAR-4_

904-HARLEY-03

Installation Instructions for

Harley

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:

- Use this fixture indoors only.

- Do not look directly at the lamp while the fixture is on.

- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.

- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.

- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.

- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.

- Do not touch lamp at anytime. Use a soft cloth. Oil from skin
may damage lamp.

- It is normal for a new halogen lamp to produce minor
smoke when first turned on.

- Do not operate the luminaire with a missing or damaged
shield.

- Turn power off and allow to cool before replacing lamp.

Install the Lamp

IMPORTANT INFORMATION

- This product is ETL listed for indoor dry locations.

- This product is not restricted to certain height installation.
It is approved to be used at any height above the floor.

- Applicable accessories are Hexcell Louver, Glass Lenses,
Gobo Holder, MR16 Snoot and Scope.

SAVE THESE INSTRUCTIONS!

A

SOCKET POST
THUMB SCREW

1

SOCKET

3: Place optional glass lens or hexcell louver into the ring.

4: Slide the socket forward to secure the lamp and accessory

against the ring, and tighten the thumb screws.

5: To rotate the fixture, loosen the ring thumb screws. Rotate
the ring to the desired position and then tighten the thumb
screws.

LAMP

2

CAUTION: To reduce risk of a burn or electrical shock during

lamping, disconnect the power to the fixture.

1: Loosen the thumb screws on the socket post and pull the
socket back.

Use MAX 75 Watt, Type MR16 Front Glass Cover Halogen
Lamp.

2: Push the lamp pins completely into the socket holes.

B

SOCKET POST
THUMB SCREW

4

RING

3

HEXCELL LOUVER
OR GLASS LENS

RING THUMB
SCREW

5

1

Install the Fixture to Monorail Connector (MC-FJ-_)

FAST JACK

C

HOUSING

MONORAIL

1

1: Place the Fast Jack housing onto the Monorail and use

fingers to tighten the Fast Jack housing connector to the Fast
Jack housing. Make sure that the Fast Jack housing

connector is not cross threaded.

2: Use fingers to tighten the Fast Jack fixture connector into the

Fast Jack housing connector.

2

FAST JACK HOUSING
CONNECTOR

2

FAST JACK
FIXTURE
CONNECTOR

Install the Fixture to Monorail
2 Circuit Connector (M2C-FJ-_)

1: Place the Fast Jack housing onto the Monorail 2 Circuit and

use fingers to tighten the Fast Jack housing connector to the
Fast Jack housing. Make sure that the Fast Jack housing

connector is not cross threaded.

2: Use fingers to tighten the Fast Jack fixture connector into

the Fast Jack housing connector.

CIRCUIT #1 CIRCUIT #2

E

0.05 ALLEN
WRENCH

3

#4-40 SET
SCREW

1
2
N

4

1
2
N

FAST JACK

D

HOUSING

1

FAST JACK HOUSING
CONNECTOR

3: To power the fixture from circuit #1, top and bottom
(neutral) rails, tighten the #4-40 set screw on top of the
housing with the 0.05 Allen wrench. Make sure this set

screw connection is very tight.

4: To power the fixture from circuit #2, middle and bottom

(neutral) rails, remove the #4-40 set screw from top of the
housing and tighten it into the side threaded hole with the

0.05 Allen wrench. Make sure this set screw connection

is very tight.

To avoid shorting the system, do not use more than one

NOTE:

set screw to select a circuit on the Monorail 2 Circuit connector.

MONORAIL 2 CIRCUIT

2

FAST JACK
FIXTURE
CONNECTOR

2

Install the Fixture to Fast Jack
Canopy (FJP-2SQ-_, FJP-4SQ-_,
FJP-4RD-_)

1: Use fingers to tighten the Fast Jack fixture connector into

the Fast Jack canopy connector.

NOTE: Do not load either circuit over the maximum system

rating.

F

1

FAST JACK FIXTURE
CONNECTOR

FAST JACK CANOPY
CONNECTOR

1

2