1718 W. Fullerton Ave
www.edgelighting.com
© 2012 Edge Lighting. All Rights Reserved.
info@edgelighting.com
Installation Instructions for Greta
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Use this fixture indoors only.
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Turn power off and allow to cool before replacing lamp.
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations.
- This product is wall mounted only, either vertically or
horizontally.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This product can be dimmed with a standard incandescent
dimmer.
GRETA-W-_-H1-_
M2-IND-_
CENTER MOUNT INSTALLATION
OFF-CENTER MOUNT INSTALLATION
904-GRETA-W-H1-08
SAVE THESE INSTRUCTIONS!
Disassemble the Fixture
A
GLASS SHADE
1
1
PHILLIPS SCREW
SLOT
SCREW HEAD
BACKPLATE
1: Remove the Phillips screw on the top of the glass shade and
slide the glass shade up to remove it from the backplate.
B
THREADED
STUD
THUMB
NUT
2
THREADED
STUD
BACKPLATE
SOCKET PLATE
2:
Remove the four thumb nuts from the threaded studs to
detach the socket plate from the backplate.
THUMB NUT
2
1
C
PHILLIPS SCREW
Unscrew the two Phillips screws in the center of the
3:
backplate to remove the crossbar. These screws will
be used at a different location later during
installation.
3
BACKPLATE
Feed the power wires through the crossbar center cutout.
1:
Level the two inner threaded holes (spaced 1" apart) either
2:
horizontally (to mount the Greta for vertical position), or
vertically (to mount the Greta for horizontal position).
Secure the crossbar to the electrical box with the provided
two #8-32 screws.
E
SOCKET PLATE
4
5 6
3
CROSSBAR
BACKPLATE
Install the Fixture
D
ELECTRICAL
BOX HOLE
CROSSBAR
1
#8-32 SCREW
NOTE: It is recommended a person to hold the fixture while the
electrician connects the power to the fixture.
3: While holding the fixture feed the socket plate wires into the
backplate center hole.
4: Make sure that the crossbar is grounded in accordance with
local electrical codes.
INNER
THREADED
HOLE
1" APART
7: Align the backplate screw holes to the electrical box
mounting holes, and place the backplate on wall to mark
the anchor location.
8a: If mounting fixture centered: mark the end holes of the
mounting on the wall. These marked holes are for
anchors (not provided).
8b: If mounting fixture off centered: slightly loosen the
two backplate screws and slide the mounting bar to the
desired position and tighten the backplate screws. Mark
the end holes of the mounting on the wall. These marked
holes are for anchors (not provided).
5: Connect the white fixture wire to the neutral power wire with
a wire nut.
6: Connect the black fixture wire to the hot power wire with a
wire nut.
F
CROSSBAR
MOUNTING
ADJUSTMENT
BACKPLATE
SCREW
8b
7
END
HOLE
BAR
8a8a
2
G
ANCHOR
(NOT PROVIDED)
WALL
9
9: Remove the backplate from the wall and tap the anchors on
9
the marked points up to the threaded portion with a
hammer. Screw in the threaded portion of the anchors with
a Phillips screwdriver.
ANCHOR
H
10
BACKPLATE
WARNING: When Mounting Greta vertically, the socket must
face down to avoid heat build up, damaging the socket.
10: Place all wires and wire nut connections through the
crossbar center hole properly inside the electrical box.
11: Secure the ends of the backplate to the anchors with the
two #8 screws.
12: Slide the socket plate holes onto the backplate threaded
studs and secure it in place by tighten the four thumb nuts.
13: Tighten the two #8-32 screws through the backplate holes
into the crossbar inner threaded holes to secure the fixture
in place.
Install the Lamp & Glass Shade
I
SOCKET
LAMP
11
#8 SCREW
THREADED
STUD
THUMB
NUT
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
Use MAX 40 Watt Type E11 Base, Halogen
or Xenon Lamp For each Socket.
1: Using a soft cloth, screw the lamps completely into the
sockets.
12
#8-32
SCREW
13
BACKPLATE
SOCKET PLATE
2: Align the glass shade slots with the screw heads on the side.
Push the glass shade onto the backplate and slide it down to
lock in place.
3: Secure the glass shade to the backplate by tightening the
Phillips screw. DO NOT OVER TIGHTEN PHILLIPS
SCREW, WHICH MAY CAUSE THE GLASS TO BREAK.
J
PHILLIPS
SCREW
SCREW HEAD
SLOT
2
3
3
Loading...