Edge Lighting Galleria Picture Light User Manual
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
© 2011 Edge Lighting. All Rights Reserved.
info@edgelighting.com
Installation Instructions for Galleria Picture Light
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is wall mount for indoor locations.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This product can be dimmed with a low voltage electronic
dimmer.
SAVE THESE INSTRUCTIONS!
GAL-PL-_
904-GALLERIA-04
Install the Fixture
A
FIXTURE CANOPY
3: Connect the white transformer wire to the neutral power
wire with a wire nut.
4: Connect the black transformer wire to the hot power wire
with a wire nut.
5: Place the transformer and transformer wires inside the
electrical box.
C
CROSSBAR ASSEMBLY
THREADED STUD
THE THREADED STUDS WILL INTERFERE
WITH MOUNTING SCREWS. MOUNT THE CROSSBAR
SLIGHTLY OFF CENTERED VERTICALLY.
7
6
THUMB NUT
1
2-1/8" APART
6
CROSSBAR
ASSEMBLY
2
GROUND
SCREW
ELECTRICAL
BOX HOLE
#8-32 SCREW
Loosen and remove the two thumb nuts from the front of the
1:
fixture canopy.
2: Pull the crossbar assembly off of the fixture canopy.
B
4
3
WIRE NUT
TRANSFORMER
6: Mount the crossbar assembly to the electrical box holes with
the provided #8-32 screws so that the two inner threaded
studs (spaced 2-1/8" apart) on crossbar are leveled
horizontally. Make sure to mount the #8-32 screws
just below the threaded studs for proper spacing.
7: Connect the transformer green wire to the crossbar assembly
ground screw. Make sure that the crossbar assembly is
grounded in accordance with local electrical codes.
1
D
8: Connect each transformer low voltage (blue wire) to one
8
fixture wire with a wire nut.
8
9: Place all wires and wire connections inside the electrical
box.
10: Align and slide the canopy assembly holes onto the
threaded studs. While holding the fixture, tighten the two
thumb nuts to secure the canopy in place. Make sure to
mount with the M4 set screws on the fixture arms facing up.
F
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
11
11
11
LAMP HOUSING
SOCKET
E
11: Pull out the two lamp housings from the fixture to expose
the two sockets.
M4 SET SCREW
10
THREADED NUT
THREADED STUD
CANOPY
10
9
G
LAMP HOUSING
SOCKET
NOTE: Use only fingers and a soft cloth to install the lamps.
Use only MAX 20 Watt Bi-Pin Xenon (Xelogen) lamp, or
low pressure halogen lamp specified by the lamp
manufacturer to be used with unshielded (without the
lamp shield) fixture, for each socket.
12: Push the lamp pins completely into the socket holes.
13: Replace the lamp housings and rotate the fixture arms
to a desired position.
Adjusting the Fixture Arm (Optional)
H
LIGHT
TAB
SHADE
1
2
FIXTURE BODY
2
MINIMUM OF 6"
FROM ANY
COMBUSTIBLE
MATERIAL
NOTE: Incase the fixture arms become loose proceed with the
following steps.
1: Remove the tab on the fixture body.
2: Tighten the Phillips screws inside the fixture body.
3: Replace the tab on the fixture body.
13
12
LAMP
2
Loading...