EcoSlate
Models: GDI-EXSLT800...820
User Guide
Quick Start
1 Open Cap on the back of your EcoSlate
2Turn on the Main Power Switch
3Press the Standby Button to power on your EcoSlate
4Search your Bluetooth Connection on your Smart Device
5Pair & Play
LED Status Indicators
Power, Battery Indicator,
Bluetooth, EcoConnect
Battery Level Indicators
Control Buttons
Control Buttons & Operations
On/Off 
Press the Standby Power Button once to power ON/OFF.
IMPORTANT: Standby Power function will NOT operate when the Master Power is set OFF. Master Power Switch under the cap on the back panel must be set ON for Standby & your EcoSlate to operate.
Bluetooth 
When turned ON, the EcoSlate will power on and search for your
Bluetooth. Refer to Set Up Recommendations 1-2-3 part 3 for details.
EcoConnect 
Functionality is only available between two units. Refer
to EcoConnect - Wireless Stereo Connection of Two
Speakers for details.
Speaker Volume
Press 
to decrease or 
to increase Speaker Volume.
NOTE: Some Bluetooth devices may require to be manually set for maximum audio level.
Your EcoSlate will beep to indicate when maximum volume setting is reached.
Track Selection
Press button once to select Previous Song track 
& Next Song track 
.
Play/Pause/Answer 
Press button once to pause & play song tracks and to answer mobile calls (MUST be paired with Bluetooth).
LED Flashlight 
Press the LED button once to cycle through four modes: LOW, MEDIUM, HIGH, OFF.
PRESS AND HOLD to turn the button backlights ON/OFF on the key pad.
Battery Indicator 
Connect USB to power source. LED on the top panel indicates USB connection charging status.
RED: charge in process GREEN: full charge complete
NOTE: There also are four LED Battery Level Indicators located on the top of the unit. Each LED represents 25%
of a charge. Four full LEDs indicate a full charge.
Set Up Recommendations 1-2-3
1 Charge Your EcoSlate
Before you power on your EcoSlate, connect the USB Micro port to the USB cable and a 5V power source to fully charge your EcoSlate for best performance.
NOTE: Before using your EcoSlate for the first time, charge the unit until all battery level indicators are green, indicating a full charge.
Approximately 3 hours of charging is required from a low to a full charge.
Power source options include the USB connection to your computer or a power outlet using a 5V USB to AC power adapter. It is recommended to always use the USB cable and power adapter included with your EcoSlate.
2 Power On, Battery, & LED Status Indicators
Once fully charged, press the Standby Power Button 
on the top of your EcoSlate. You will see the green LED light & you will hear, “Power on” when powering on.
IMPORTANT: Make sure that the Main Power Switch, located in the back compartment under the cap, is set in the ON position. If the switch is in the OFF position, your EcoSlate will not be able to turn on using the Standby Power Button.
The LED battery level indicators are located on the top of the unit. Each bar represents 25% of a charge, with 4 full LEDs indicating a full charge.
Audio playback time over Bluetooth connection is approximately 12 hours at 75% volume.
3 Bluetooth Pairing & Your Audio
Connecting With Bluetooth:
Connect To Your Smart Device & Play Audio
When your EcoSlate is turned on, the blue LED light on the top panel will flash, indicating the unit is ready to pair.
Turn on Bluetooth on your Bluetooth device (Smart Device) and set the device in pairing mode. Available Bluetooth connections shall appear. Select the ECOXGEAR speaker from the list of discovered devices on your Bluetooth device. Wait for a few seconds until the connection is completed.
NOTE: Bluetooth connection feature is found in the Settings section of most mobile phones and other Bluetooth enabled devices.
When the ECOXGEAR selection is made and the Bluetooth connection is completed, your EcoSlate will announce: “Connection successful”
Once connected, select and play your desired audio.
Pairing Mode: If the LED is not flashing or if you wish to place your EcoSlate in pairing mode, press and release the Bluetooth button on the top panel. Your EcoSlate shall announce “Ready to connect” when ready to pair to a new device.
NOTE: Your EcoSlate shall sync & wirelessly pair with most Bluetooth enabled devices. The unit remembers the last device paired and will automatically search for previous connections when the speaker is turned on or when a device comes back into Bluetooth range. If a connection is lost due to range, the speaker will look to re-establish that connection. If Bluetooth is turned off on your Smart Device, the EcoSlate may not automatically look for the device.
RECOMMENDATION: If you are not familiar with Bluetooth pairing for your Smartphone or other Smart Device, refer to the User Guide for your Smartphone to learn how to add and pair a new device (EcoSlate for instance) to your Smartphone using Bluetooth.
Bluetooth Pairing & Connections: Once paired, should you have an issue switching between Bluetooth connections between devices, open the Bluetooth Section within the device currently connected to the EcoSlate and delete the Bluetooth connection. The EcoSlate will then be available to pair & connect to an alternate Bluetooth enabled Smartphone / Audio Device.
Loading...