EcoxGear GDI-EGST700--710 Quick Start User Manual

Quick Start USER GUIDE

ECOSTONE Features & Operation Models: GDI-EGST700--710

QUICK START 1-2-3

STEP 1: Power ON your ECOSTONE
STEP 2: SEARCH your Bluetooth Connection on your Smart-device
STEP 3: PAIR & PLAY

STANDBY

ON/OFF

BLUETOOTH

SPEAKER

VOLUME

TRACK

SELECTION

PLAY PAUSE

ANSWER

LED

FLASHLIGHT

Quick Start USER GUIDE

STEPS 1-2-3 Set Up Recommendations

STEP 1 CHARGE your ECOSTONE

Before you power on your ECOSTONE connect the USB Micro port to the USB cable and a power
source to fully charge your ECOSTONE for best performance.

NOTE: Before using your ECOSTONE for the first time, charge the unit until all 4 LED battery level

indicators are solid green, indicating a full charge.

 Typically approximately 3 hours of charging is required from a low to a FULL charge.

 Power source options include the USB connection to your computer or a power outlet using a USB to

AC power adapter. Recommend always using the USB cable included with your ECOSTONE.

STEP 2 Power ON, Battery & LED Status Indicators

Once fully charged, press the STANDBY POWER button on the top of your ECOSTONE.
You will see the green LED light & you will hear an ascending bell tone when powering ON.

IMPORTANT: be sure the MAIN POWER switch located in the back compartment under the cap is set in

the UPPER ON position. IF the switch is in the LOWER OFF position your ECOSTONE will not be able to
turn ON using the Standby button.

 The LED battery level indicators are located on the top of the unit. Each bar represents 25%,

4 full LED’s indicates a FULL charge

 AUDIO playback time over Bluetooth connection is approx. 12 hours at 75% max. volume

Quick Start USER GUIDE

STEP 3 Bluetooth pairing & your Audio

Connecting with Bluetooth: connect to your Smart-device & play AUDIO

When your ECOSTONE is turned ON the blue LED light on the top panel will flash rapidly indicating the unit is ready to
pair.

Turn on Bluetooth on your Bluetooth device (Smart-device) and set the device in pairing mode. Available Bluetooth
connections shall appear. Select the ECOXGEAR speaker from the list of discovered devices on your Bluetooth device.
Wait for a few seconds until the connection is completed.

When the ECOXGEAR selection is made and the Bluetooth connection is completed your ECOSTONE announces:
“Bluetooth connected”

Once connected, select and play your desired audio
NOTE: IF the LED is not flashing or if you wish to place your ECOSTONE in pairing mode, press and release the

Bluetooth button on the top panel. Your ECOSTONE shall announce “pairing ready” when ready to pair to a new device.
NOTE: Your ECOSTONE shall sync & wirelessly pair with most Bluetooth enabled devices. The unit remembers the last

device paired and will automatically search for previous connections when the speaker is turned ON or when a device
comes back into Bluetooth range. If a connection is lost due to range, the speaker will look to re-establish that connection.
IF Bluetooth is turned OFF on your Smart-device, the ECOSTONE will not automatically look for the device.

RECOMMENDATION: IF you are not familiar with Bluetooth pairing for your Smartphone or other Smart-device refer to
the User Guide for your Smartphone to learn how to add and pair a new device (ECOSTONE for instance) to your
Smartphone using Bluetooth.

NOTE: Bluetooth Pairing & Connections - Once paired, should you have an issue switching between Bluetooth
connections between devices, open the Bluetooth Section within the device currently connected to the ECOSTONE and
delete the Bluetooth connection. The ECOSTONE will then be available to pair & connect to an alternate Bluetooth
enabled Smartphone / Audio Device

Quick Start USER GUIDE

Control Buttons & Connections, Functions & Feature

STANDBY

ON / OFF

PRESS the STANDBY POWER button to turn the ECOSTONE ON/OFF.

When turned OFF the ECOSTONE remains in STANDBY POWER mode.
IMPORTANT: Standby Power function will NOT operate when the
MASTER POWER is set OFF. Master Power Switch on the back panel
must be set ON for Standby & your ECOSTONE to operate.

BLUETOOTH

When turned ON, the ECOSTONE will power on and search for your
Bluetooth. Refer to STEP 3 for details

SPEAKER

VOLUME

PRESS - to decrease the volume & PRESS + to increase the volume
NOTE: Some Bluetooth devices may require they are manually set at

max. for max. level audio
Your ECOSTONE will beep to indicate when the + button is pressed and
maximum volume setting is reached

TRACK

SELECTION

PRESS < for previous track selection & PRESS > to advance the track

selection

PLAY PAUSE

ANSWER

PRESS button once to PAUSE & PLAY song tracks and to ANSWER
mobile CALLS

LED

FLASHLIGHT

PRESS the LED button once to turn ON the flashlight. PRESS a
second time to turn OFF

TOP PANEL [on the top]