EchoStar 9630 LP, 9630 User Manual

AutoScan Satellite System

9630 9630-LP

Installation and Operating Instructions

11200 Hampshire Avenue South, Bloomington, MN 55438-2453

Phone: [phone] Fax: [phone]

www.kingcontrols.com

1352 REV M

Satellite Solutions for Mobile Markets

AutoScan

TM

Page 1

IMPORTANT!

The satellite TV market is expanding and changing. The information in this manual was
accurate at the time of printing. If your King-Dome does not operate as outlined in this
manual please call King Controls at ( 800) 982-9920 or visit our website at
www.kingcontrols.com.

TABLE OF CONTENTS

Section Contents Page

1. INTRODUCTION.....................................................................................2

2. DEFINITION OF TERMS........................................................................3

3. INSTALLATION..................................................................................4-10

4. OPERATION ....................................................................................11-15

5. STORE/RECALL POSITIONS ..............................................................16

6. DIAGNOSTICS .....................................................................................17

7. MAINTENANCE....................................................................................18

8. LIMITED WARRANTY ..........................................................................19

DIRECTV is a registered trademark of DIRECTV, Inc.
Dish Network®is an official trademark of Echostar Communications Corporation.
Bell ExpressVu

®

is an official trademark of Bell Canada.

DVB®is a trademark of the DVB Digital Video Broadcast Project (1991-1996)

Page 2

The King-Dome AutoScan Satellite System includes 2 main components (Fig. 1).

Dome (Antenna) Unit Located on the roof of the vehicle. The dish is covered by a

protective dome that keeps operational components free from
the elements.

Controller Located in the vehicle. Used to activate the system, position

the dish, and access diagnostic information.

SECTION 1

INTRODUCTION

Note: A TV, satellite receiver, and program subscription are also required for satellite TV

viewing. (Not supplied by King Controls.)

Fig. 1

Page 3

AZIMUTH: Circular rotation around the vehicle.

(like a clock face: front of vehicle is 12:00, rear is 6:00) (Fig. 2)

ELEVATION: Angle in degrees measured from the ground plane (Fig. 3).

SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission.

SECTION 2

DEFINITION OF TERMS

Fig. 2

Fig. 3

Page 4

KIT CONTENTS:

1. Unpack and identify all components (Fig. 4).

SECTION 3

INSTALLATION

Fig. 4

TOOLS AND MATERIALS REQUIRED:

- drill and drill bit set

- tape measure

- 7/16” open end wrench (coax connections)

- adhesive sealant (compatible with roof material)

- appropriate fasteners to install all components and wiring

- 5/32” allen wrench, channel lock or pliers (to remove shipping bolts)

- wire cutter (to remove shipping tie strap)

KING CONTROLS

KING-DOME

KING DOME

OPERATING INSTRUCTIONS

1. Turn on TV

2. Go to signal meter screen and choose
transponder number for dish or direct tv.

3. Enter local zip code on signal meter
screen to determine satellite elevation..

4. Press UP arrow to turn King Dome on.

5. Press UP or DOWN arrow to display dish
elevator and match to elevation on signal
meter screen on tv.

6. Press and hold RIGHT arrow for 10
seconds. Dish will perform a 360 degree
scan for satellite. When signal strength
appears on tv, press ANYBUTTON to
stop dish from rotating.

7. Press the UP, DOWN, RIGHTor LEFT
arrows to fine tune signal strength to the
highest possible number on tv signal
meter screen.

Page 5

IMPORTANT! The tie strap and spacer, and the bolts and washers must be removed

from the bottom of the dome unit prior to installation. DO NOT REMOVE
THE DOME COVER TO REMOVE THESE SHIPPING RESTRAINTS.

YOU MUST PLUG THE SHIPPING BOLT HOLES WITH THE SUPPLIED
PLUGS (ATTACHED TO TIE STRAP SHIPPING RESTRAINT).

2. Remove and discard the tie strap and spacer (KEEP RUBBER PLUGS), and the (2) bolts
and (2) washers that pass through the bottom of the base (Fig. 5).

3. Insert provided plugs into holes that were occupied by the shipping bolts. Inserted plugs
should be flush with base (Fig. 5).

Fig. 5

IMPORTANT!
Remove and discard
Tie Strap and Plastic

Spacer prior to

installation.

KEEP RUBBER

PLUGS.

IMPORTANT!

Remove and discard

Bolts and Washers

prior to installation.

IMPORTANT!

After removing shipping bolts, firmly

insert plugs into holes. Plugs should

be flush with base.

Page 6

DOME LOCATION

4. Select an area on the roof for the dome unit and the location where the wiring will enter
the vehicle through the roof to the satellite receiver, controller, and 12 volt power source
inside, using the following criteria:

a) The shortest distance between the dome unit and the satellite receiver is most

desirable.
b) The dome unit requires a 28 inch diameter mounting area.
c) The dome unit must be mounted on the centerline of the vehicle. Mounting off

centerline reduces electronic level compensation.
d) There must be no “line of sight” obstructions. Air conditioning units, other antennas,

and storage areas that are too close to the dome unit may prevent the satellite

signal from reaching the dish (Fig. 6).

HEIGHT OF

OBSTRUCTION

APPROXIMATE

MINIMUM DISTANCE

TO DOME EDGE

10” 8”
11” 10”
12” 12”

13” 14”
14” 16”
15” 18”
16” 20”

Fig.6

IMPORTANT! For installations on trucks with air shields, a bracket must be used for

mounting the dome unit. The dome unit MUST

be mounted to the air ride

cab: NEVER to any structure mounted directly to the frame.

See bracket instructions for proper installation (Fig. 7).