Echo LS21 Instruction v.8

Instructions
SUBJECT: CYLINDER BRACE
KITS, Part #' 77640-00 & 77641-00
WARNING
Before inspecting or servicing any part of this machine, shut off power source, remove key, disconnect the battery cables and make sure all moving parts have come to a complete stop.
FITS MODELS: LS21 (77640-00) &
LS27 (77641-00)
This kit is used to install a cylinder brace on a Log Splitter. Use of the cylinder brace is recommended in areas where the Log Splitter will be used in a Rental application or be towed over rough terrain. The brace stabilizes the cylinder during towing and can help prolong its life.
IMPORTANT
Towing speeds are NOT to exceed 45 mph.
INSTALLATION:
Refer to parts list on reverse.
1. Insert new support plate into place at end of beam under the cylinder as shown in Fig. 1.
2. Secure on operators side with two 3/8" self-tapping screws.
Fig. 2, two 3/8" Self-tapping screws on operator's side
NOTE
If a quick split kit has been previously installed, it will be necessary to remove it from the channel mount plate and mount it directly to the new cylinder brace plate at the two hole locations detailed in Fig. 2.
Fig.1, Cylinder brace plate in position on log splitter
3. Secure on engine side with two 3/8 x 1-1/2" bolts, four
Fig. 3, two 3/8 x 1-1/2" bolts, four washers and two nylock nuts
Instruction Sheet
washers and two nylock nuts.
on engine side
PN 77642-00
Rev.040113
4. Place top clamp into place over the cylinder. 5. Secure top clamp using the four 3/8 x 1-1/4" carriage bolts and nylock flange nuts.
Fig. 4, "C" shaped top clamp goes over cylinder brace
LS21 CYLINDER BRACE KIT, PN 77640-00
ITEM PART # DESCRIPTION QTY
1 15007 BOLT 3/8*1-1/2 GR5 HCS ZP 2
2 15031 WASHER, 3/8" FLAT ZP (67PCS/LB) 4
3 15076 SCREW,3/8-16*1"LG THD CUTT ZP 2
4 15378 BOLT, CARR 3/8*1-1/4"GR5 NC ZP 4
5 15388 NUT, 3/8" NE NYLOCK ZP 2
6 15905-00 NUT, 3/8-16 NYLOCK FLANGE 4
7 77629-12 CLAMP, CYLINDER SUPPORT TOP 1
8 77634-12
WELDMENT, CYLINDER SUPPORT LS21
1
Fig. 5, Top clamp secured using 3/8" carriage bolts and nylock
ange nuts
LS27 CYLINDER BRACE KIT, PN 77641-00
ITEM PART # DESCRIPTION QTY
1 15007 BOLT 3/8*1-1/2 GR5 HCS ZP 2
2 15031 WASHER, 3/8" FLAT ZP (67PCS/v) 4
3 15076 SCREW,3/8-16*1"LG THD CUTT ZP 2
4 15378 BOLT, CARR 3/8*1-1/4"GR5 NC ZP 4
5 15388 NUT, 3/8" NE NYLOCK ZP 2
6 15905-00 NUT, 3/8-16 NYLOCK FLANGE 4
7 77633-12 CLAMP, CYLINDER SUPPORT 1
8 77638-12
WELDMENT, CYLINDER SUPPORT LS27
1
ECHO BEAR CAT
www.bearcatproducts.com
237 NW 12th Street, West Fargo, ND 58078-0849
Phone: 701.282.5520 • Toll Free: 800.247.7335 • Fax: 701.282.9522
E-mail: service@bearcatproducts.com • sales@bearcatproducts.com
Loading...