Hedge Clipper
Operator's Manual
MODEL HC-201
Serial Number 02001001 - 02999999
X7532240101
WARNING DANGER
Read rules for safe operation and all instructions carefully. ECHO provides this
Operator's Manual and a Safety Manual. Both must be read and understood for
proper and safe operation.
X753000071
12/01
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operations tips and SAFETY messages.
THE OPERATOR'S MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It contains specifications and information for
operation, starting, stopping, maintenance, storage and assembly
specific to this product.
THE SAFETY MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It xplains possible hazards involved with the
use of Hedge Clippers and what measures you should take to make
their use safer.
TABLE OF CONTENTS
Introduction...............................................................2
- The Operator's Manual ....................................... 2
- The Safety Manual .............................................2
Manual Safety Symbols and Important Information ..... 3
Safety ......................................................................... 3
- Decals ................................................................. 3
- International Symbols ........................................4
Safety Instructions .................................................... 4
- Personal Conditions and Safety Equipment .......4
- Extended Operation/Extreme Conditions ............5
- Equipment ...........................................................5
- Safe Operation .................................................... 6
Emissions Control......................................................6
Description ................................................................ 7
- Contents .............................................................7
Specifications ............................................................9
Assembly ................................................................... 9
Pre-Operation........................................................... 10
- Fuel ................................................................... 10
Operation ................................................................. 11
- Starting Cold Engine......................................... 11
- Starting Warm Engine ...................................... 12
Copyright© 2001 By Echo, Incorporated
All Rights Reserved.
- Stopping Engine ............................................... 13
- Hedge Trimming ...............................................13
Maintenance............................................................ 14
- Skill Levels........................................................ 14
- Maintenance Intervals ...................................... 14
- Air Filter ........................................................... 15
- Fuel Filter.......................................................... 15
- Spark Plug ........................................................ 16
- Cooling System ................................................ 16
- Exhaust System ................................................ 17
- Carburetor Adjustment..................................... 18
- Lubrication .......................................................20
- Sharpening Blades............................................ 21
Troubleshooting...................................................... 22
Storage..................................................................... 23
Servicing Information .............................................. 24
- Parts.................................................................. 24
- Service ..............................................................24
- ECHO Consumer Product Support ................... 24
- Warranty Card.................................................. 24
- Additional or Replacement Manuals................ 24
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories,
and may not include all standard equipment.
HEDGE CLIPPER
OPERATOR'S MANUAL
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead to
serious personal injury to operator and bystanders.
IMPORTANT
The enclosed message provides
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
information necessary for the protection of the unit.
NOTE
This enclosed message provides tips
for use, care and maintenance of the
unit.
3
SAFETY
DECALS
Locate these safety decals on your unit. Make sure the decals are
legible and that you understand and follow the instructions on them. If
a decal cannot be read, a new one can be ordered from your ECHO
dealer. See PARTS ORDERING instructions for specific information.
P/N X505000270
P/N 89016006361
P/N X5052242200
4
INTERNA TIONAL SYMBOLS
Symbol form/shape
Symbol
description/application
Read and understand
owners manual.
Symbol form/shape
Symbol
description/application
Fuel and oil mixture
Symbol form/shape
Symbol
description/application
Carburetor adjustment
- Low speed mixture
Symbol form/shape
Symbol
description/application
Carburetor adjustment
- High speed mixture
Wear eyes, ears and
head protection
Emergency stop
Wear hand protec-
tion. Use two handed.
Engine choke
control.
Chain lubrication
Ignition
SAFETY INSTRUCTIONS
PERSONAL
CONDITION AND SAFETY EQUIPMENT
Finger Severing
Hot
Surface
DO NOT smoke
near fuel.
Ignition
ON/OFF
Do not operate
without guards
in place.
Safety/Alert
Avoid all power
lines. This unit is not
insulated against
electrical current.
Plan retreat path
from falling
objects.
DO NOT allow
flames or sparks
near fuel.
Carburetor adjustment
- Idle speed
Do not operate clos-
er than 15 M (50 ft.)
from electrical haz-
ards.
Primer bulb
Wear slip resistant
foot wear.
Keep bystanders at least
4.5 meters (15 feet) away.
W ARNING DANGER
Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a hedge clipper.
Eye Protection
Eye protection that meet ANSI Z87.1 or CE requirements
must be worn whenever you operate the Hedge Clipper.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the handles. Gloves also reduce the transmission
of machine vibration to your hands.
Hearing Protection
Wear hearing protection. ECHO recommends wearing
hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARFS, JEWELRY.
Wear protective hair covering to contain long hair.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
EXTENDED OPERATION/EXTREME CONDITIONS
HEDGE CLIPPER
OPERATOR'S MANUAL
5
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals, may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations, followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended, because the minimum exposure which might trigger the
ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands,
and wrists.
• Maintain good blood circulation by performing vigorous armexercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms, and shoulders may cause soreness, swelling, numbness,
weakness, and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the
following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to
maintain a straight wrist position. Also,
when grasping, use your whole hand, not
just the thumb and index finger.
• Take periodic breaks to minimize repetition
and rest your hands.
• Reduce the speed and force with which
you do the repetitive movement.
• Do exercises to strengthen the hand and
arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel
tingling, numbness, or pain in the fingers,
hands, wrists, or arms. The sooner RSI/
CTS is diagnosed, the more likely permanent nerve and muscle damage can be
prevented.
EQUIPMENT
W ARNING DANGER
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments, or accessories which have
not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety
manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Never adjust blades when the engine is operating.
• Inspect hand guard for damage. Replace if damaged or missing.
• Check that the blade assembly is firmly attached and in safe operating
condition. Dull, loose or damaged blades should not be used.
• ECHO, INC. will not be responsible for the failure of cutting devices
or accessories which have not been tested and approved by ECHO
for use with this unit.
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
6
SAFE OPERATION
W ARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
Provide all users of this equipment with the Operator's Manual and
instructions for Safe Operation.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
fingers tightly encircling the handles.
EMISSION CONTROL
California Tier 2
The emission control system for this engine is EM/TWC
(Engine Modification and Catalyst).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: YEHXS.0214CA DISPLACEMENT: 21.2 CC
EMISSION COMPLIANCE PERIOD: 300 HOURS
THIS ENGINE MEETS U.S. EPA PH 2 AND 2000 AND LATER
CALIFORNIA EMISSION REGULATIONS FOR S.O.R.E. REFER
TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS
AND ADJUSTMENTS.
Emission Control Label (located on Engine) (EXAMPLE
ONLY, information on label varies by FAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable California and/or U.S. EPA emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of this manual.
The Air Index Tag indicates, for purposes of
consumer awareness, how this product's
emissions compare to other products under the
standards enacted by the California Air Resources Board.
AIR INDEX TAG
HEDGE CLIPPER
OPERATOR'S MANUAL
DESCRIPTION
The ECHO product you purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
CONTENTS
__ 1 - Hedge Clipper Assembly
__ 1 - Operators Manual
__ 1 - Safety Manual
__ 1 - Warranty Statement
__ 1 - Warranty Registration Card
__ 1 - Plastic Bag
__ -- 1, T-Wrench 13 x 19
__ -- 1, 8 mm x 10 mm Open end Wrench
__ -- 1, Bottle 2.6 oz. 2-Cycle Oil
__ 1 - Blade Cover
1
7
10
11
16
14
13
12
6
7
9
8
15
2
5
4
3
8
1. BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of cutting
on either side of the blade. All other models are single sided.
2. RIGHT FRONT HANDLE WITH GUARD - Rubber non-slip grip, guard protects hand from the blades. Warning
decals are located on guard.
3. SPARK PLUG - Provides spark to ignite fuel mixture.
4. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-
tor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an
additional 4 or 5 times.
5. CHOKE - The choke control lever is located on the front of the air cleaner case. Move choke lever to "COLD
START" to close the choke for Cold Starting. Move choke lever to "RUN" position to open choke.
6. AIR CLEANER - Contains replaceable filter element.
7. FUEL TANK CAP - Covers and seals fuel tank opening.
8. FUEL TANK - Contains fuel and fuel filter.
9. REAR HANDLE - Contains the Stop Switch, Throttle Lockout, Rotation Lockout and Throttle Trigger.
10. THROTTLE TRIGGER - Spring loaded to return to idle when released. Trigger Lockout must be depressed fully and
Rotation Lock must be engaged before Throttle Trigger will move. During acceleration, depress gradually for best
operating technique.
11. STOP SWITCH - "SLIDE SWITCH" mounted on top of the rear handle. Move switch FORWARD to RUN, BACK to
STOP.
12. THROTTLE TRIGGER LOCKOUT - This lever must be depressed before Throttle Trigger can be activated.
13. RECOIL STARTER HANDLE - Pull handle slowly until recoil starter engages, then quickly and firmly. DO NOT pull
rope all the way out or allow the handle to snap back, damage to the starter will occur.
14. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaust area clear of flammable debris.
15. BLADE COVER - Used to cover blades during transportation or storage. Remove blade cover before using unit.
16. SAFETY VIDEO - (Not included with unit) P/N 99922202800 English version only is available at a cost of $5.00 from
ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information
on safe operation.
Loading...