EarthWay FLEX-SELECT F80 Series, FLEX-SELECT F130 Series Assembly And Operating Instructions Manual

F80 & F130 FLEX-SELECT® Series

Adaptable Broadcast Spreader
Assembly and Operating Instructions

PLEASE CONTACT US: IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY
QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME
TECHNICAL SUPPORT. SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: [e-mail]

HELPFUL HINTS:

; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The

impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller
after each use as some fertilizer may become stuck on the impeller blades and will cause uneven spreading.

; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate.

; Clean and dry your spreader thoroughly after each use, wash between the shut-off plate and bottom of the hopper

regularly. To prevent rust, coat all metal parts (inside and out) including the frame tubes with a light oil, silicon spray, or
Fluid Film®.

; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
; When using Rock Salt to prevent damage to the gearbox remove salt from the hopper daily. Rock Salt will reconstitute

back into a solid block if left in the hopper overnight and will damage your gearbox if pushed with the salt in place.

WARNING

Do not use air tools to assemble.

To prevent seizing coat all bolts

with a wax or grease prior to

installation.

Remove all parts, hardware, and assemblies from carton

and lay them out on the oor to help in assembly.

Below are tools needed for assembly - 7/16”

wrench, ratchet and 7/16” socket, and pliers.

The following photos are for assembly
purposes, and please follow them from left to
right, top to bottom.

Download a color version of this

manual online at www.earthway.com

or Scan this QR Code.

©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, FLEX-SELECT®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc.

Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507

9-2014 Pt# F52157 PAGE 1

ASSEMBLY

1

2

3

4

PAGE 2

ASSEMBLY - continued

5

6

7

8

PAGE 3

ASSEMBLY - continued

9

10

11

12

PAGE 4

ASSEMBLY - continued

13

CONFIRM THE CALIBRATION:

Lever at #30 and the drop holes fully open

COMPLETE ASSEMBLY:

Install agitator, bend the agitator up slightly to

prevent contact with the standard output tray,

and install debris screen

(press over 1/4 turn fasteners to secure)

14

PAGE 5

TRAY INSTALLATION

HIGH-OUTPUT AND LOW-OUTPUT:

require the use of the Part #F12117

HIGH-OUTPUT AND LOW-OUTPUT:

require the use of the Part #F12117

PAGE 6

SPREAD PATH

FULL Rate (one pass)

© 2013 Earthway Products, Inc. All rights reserved

HALF Rate (two passes)

5-YEAR LIMITED WARRANTY

Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years
to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc.
at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect
installation, mishandling, misuse, tampering, or normal wear and tear as determined by Earthway. Earthway at its discretion
may require that the part(s) or product be returned along with the original purchase receipt at owners’ expense for examination

and compliance with the terms of this warranty. Do not return any product without rst receiving authorization from Earthway

Products, Inc. To seek remedy under this warranty, contact Earthway Products, Inc. at 574-848-7491, techsupport@earthway.
com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe the nature of the manufacturing
defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair

or replacement of non-conformances are specically excluded. Due to the corrosive nature of most fertilizers and ice melt
products, Earthway Products, Inc. makes no warranty against and specically excludes part(s) or product degradation or

failure due to corrosion or its effects. Clean and dry your spreader thoroughly after each use, as a preventative measure, coat
all metal parts with a light oil or silicon spray, pay most attention to the inside of steel tubing where corrosion will start.

OPERATING INSTRUCTIONS

Before lling hopper, become familiar with the operation of this spreader.

5 Obtain proper setting for material to be used from the enclosed SETTING MATRIX included with this spreader, or from our

web site under the MANUALS SECTION.

5 Move stop bolt on rate gauge assembly to the proper setting.
5 While pushing spreader forward, pull control lever back to stop bolt.
5 To stop, push lever forward to close ow holes before you stop moving.
5 When nished, empty any remaining material from hopper.
5 Thoroughly wash spreader and allow to dry before storing. Apply coating of light oil to help prevent corrosion.
5 If you use Rock Salt, remove agitator when using Rock Salt to prevent damage to the gearbox.

Earthway Products, Inc.

1009 Maple Street, PO Box 547

Bristol, IN 46507

For Your Records

Date Purchased

Place of Purchase

All spare parts listed may be ordered direct from

Be sure to give the following information when ordering.

Call [phone], 800-294-0671, or email: parts@earth-

HOW TO ORDER SPARE PARTS

EarthWay Products, Inc.

Model Number

Part Number

Part Description

way.com for current prices.

Using the EV-N-SPRED®

S

p

r

e

a

d

P

a

t

t

e

r

n

Adjustable Throwing Ports
with 8 repeatable settings

to balance the left or right

spread pattern to

the center.

Dual Port PRO Adjustable
Shut-Off System - Included with Optional F13130DKit Tray

The EV-N-SPRED® Dual Port PRO Adjustable Shut-Off System is
included on all Professional models and allows the operator
to balance the spread pattern evenly across the full 180o
spread width, regardless of the weight or size of granular
material. By closing either the right and or left side
throwing ports you can balance the spread pattern to
exacting precision without compromising spread width or
application rate.

Each EV-N-SPRED
Shut-Off System drop hole has a corresponding 1/3rd
coverage area on the spread width of the spreader leaving a
feathered-edge for overlapping the spread path. The illustration to
the right shows each port and the corresponding 1/3rd coverage
area of the spread path. These ports can be adjusted to effectively
balance the spread pattern, giving equal amounts of material
across the full 180o spread pattern.

EV-N-SPRED®Dual Port PRO System Setup

Test all material prior to beginning your spreading job. You will need
a 50’ measuring tape, a small scale to weigh the material, bucket or
container to hold the material for re-weighing, chalk or a line marking
device, and (7) low baking tins. Using the EarthWay® Bag Calibrator

#77016 can greatly reduce the time needed for
determining the Setting Rates on any material but
is not mandatory to establish a setting rate.

1. Evaluate the material being spread by comparing
it to the following standard as a reference.

Large/Heavy is the size of a BB (⅛ in / 3mm), spread width is 28 - 36 feet (8.5 -

11 meters)

Dual Port PRO Adjustable

®

FINE

MEDIUM LARGE

Gauge & Lever

15

Medium/Mixed (½ the size of a BB), spread width is 20 - 24 feet (6.1 - 7.3 meters)

Small/Fine (the size of sand), spread width is 16 - 18 feet (4.8 - 5.5 meters)

2. Add a small amount of the material into the spreader, enough to cover

the bottom (2-3 in / 5 - 7 cm) and begin to test for spread width. Set the
stop on the gauge to #15 and push the spreader several feet /meters at
normal walking speed on a at hard surface (where the material will be

visible), and OPEN the lever to the STOP while continuing to walk for 3-4
paces, and CLOSE the shut-off and STOP (don’t move the spreader from
that position). Measure the spread width and evaluate the spread pattern
for even distribution on either side of the spread width center line. TIP:
Typical spread width references are listed above. The spread width that

you measure is used to calculate the actual Setting Rate for the material.

SPREAD WIDTH

P

d

a

e

r

p

S

a

t

t

e

r

n

ADJUSTING THE EV-N-SPRED® DUAL PORT SHUT-OFF SYSTEM

Next, using the (7) low baking tins position, them in a straight line on 2-foot
centers across the spread width as shown at the right.

Adjust the left or right variable throwing ports to EVEN THE SPREAD pattern.
TIP: For large/heavy materials, close the LEFT SIDE (LINES) port slightly
before you start your EV-N-SPRED® test. For small/light materials, open the
LEFT SIDE (LINES) port fully and close the RIGHT SIDE (CIRCLES) port
slightly before you start your EV-N-SPRED® test. With BOTH ports closed, the
spread is only from the center port, and will give you a 3-4ft spread width in the center
of the spreader - great for medians.
Begin pushing the spreader several feet before the line of tins and at normal walking
speed. Walk along the Center Line, and OPEN the Lever to the STOP 3-4 paces
before the line of tins and continue walking past the tins 1 or 2 paces and CLOSE the
Lever and STOP.
Visually evaluate the material in the baking tins to determine if your
spread pattern is balanced - having the same amount of material in each
baking tin.
Empty each tin back into the spreader, adjust the ports and RETEST until

you are satised that the coverage is balanced.

Spread width

in feet

7 142’ 10” 17 58’ 10” 27 37'
8 125’ 18 55’ 7” 28 35' 9"

9 111’ 1” 19 52’ 7” 29 34' 6"
10 100’ 20 50’ 30 33' 4"
11 90’ 11” 21 47' 7" 31 32' 3'
12 83’ 4” 22 45' 5" 32 31' 3"
13 76’ 11” 23 43' 6" 33 30' 4"
14 71’ 5” 24 41' 8" 34 29' 5"
15 66’ 8” 25 40' 35 28' 7"
16 62’ 6” 26 38' 6" 36 27’9”

Length needed

for 1,000 Sq Ft

Spread width

in feet

Length needed
for 1,000 Sq Ft

Spread width

in feet

Length needed

for 1,000 Sq Ft

S

p

r

e

a

2’ 2’ 2’2’2’2’

d

P

a

t

t

e

r

n

ESTABLISH THE SETTING RATE

Remove the material from the hopper, and mark the distance that you need
to travel with the spreader to attain the designated coverage area - i.e.
1,000 square feet using the spread width you determined earlier. Above

is a chart to help determine the distance needed for 1,000 square foot
calculation.

Mark the START and END POINTS on the surface required for the test.

Weigh a small amount (10-20lbs/4-9kg) of the material, and add that into

to the spreader. Using the Setting Matrix included with the spreader,
estimate a setting rate based on material manufacturers recommendations
and adjust the STOP on the Gauge to that position.
Now to test, start walking 1-2 paces before the STAR T LINE and OPEN
the Lever to the stop and then CLOSE when you cross the END POINT
LINE.
Pour the remaining material from the spreader and weigh to calculate the
amount applied over the area. Adjust the Setting Rate to a higher number
if you need to increase the application rate, or to a lower number if you
applied too much in the test.
You may need to repeat this process to acquire the exact rate.

The EV-N-SPRED® Dual Port PRO Adjustable Shut-Off System ensures that EarthWay® Professional spreaders
evenly spread all types of fertilizers, seed, ice melt, or other granular products, and is only available from
EarthWay®.

COVERAGE AREA

i.e. 1,000 SQ FT

END

START

22

5

33

19

20

19

13

14

17

23

39

34

37

35

F77080 or F77130

OPTIONAL

Heavy-Duty

Rain Cover

1”

Bolt Identifier

1-1/2”

15

31

18

10

13

44249

27

8

21

1

7

60060RNC
OPTIONAL

Left Side Deflector Kit

14

13

4

32

2”

2-1/4”

2-3/4”

16

29

6

25

30

11

10

13

3

26

38

2

28

15

18

9

27

12

24

40

19

F80 & F130 CommerCial BroadCast spreader

Key # Part # Description Key # Part # Description

1 12110 IMPELLER 9" ROUND DISHED

2 12147 SPACER (PIVOT LINK) 24 36300 1/4-20 NYLON INSERT LOCKNUT S.S.

3 12148 AXLE BEARING 25 37100 1/4-20 X 1" CARRIAGE BOLT ZINC

4 12152 AXLE BUSHING 26 42256 CONTROL ROD

5 12209 HOPPER BUSHING 27 44249 FRAME BRACE

6 12344 HANDLE SPACER 28 60027 WING NUT ASSEMBLY BLACK

7 24500 AXLE 29 60175 UPPER HANDLE SQUARE W/GRIP ea

8 25228 CROSS BRACE 11.25” 30 60298 GAUGE & LEVER ASSEMBLY

9 25108 FRAME 31 60300 PIVOT & BRACKET ASSEMBLY

10 25222 LOWER HANDLE 32 70138 PNEUMATIC DRIVE WHEEL STUD

11 25223 HANDLE SHAFT 33 F12135 1/4 TURN FASTENER FLEX SELECT

12 25723 FRAME Foot 34 F12219 STANDARD OUTPUT FLEX-SELECT SHUTOFF

13 31100 1/4-20 X 1 1/2 HHMS ZINC 35 F13105 FLEX-SELECT 80# HOPPER / F13106 FLEX-SELECT 130# HOPPER

14 31106 1/4-20 X 2 1/4" HHCS ZINC 36 F13130 STANDARD OUTPUT FLEX-SELECT TRAY KIT

15 31120 1/4-20 X 2" HHCS ZINC 37 F40003 SQUARE SCREEN FLEX-SELECT

16 31127 ROD CLIP (Flex-Select) 38 F44251 PIVOT ROD STD OUTPUT FLEX-SELECT

17 31138 #8 X 3/8" PMT #8 HD COARSE BLACK 39 F60333 GEAR BOX ASSEMBLY FLEX -SELECT

18 32100 1/4-20 HEX NUT ZINC 40 43020 BACKPLATE WASHER (FOR F130)

19 32103 1/4-20 NYLON INS LOCKNUT ZINC Optional 60060RNC SIDE DEFLECTOR

20 33108 3/16" X 1" COTTER PIN ZINC Optional HEAVY DUTY RAIN COVER (F77080 for F80 / F77130 FOR F130)

21 33109 3/16" X 2" COTTER PIN ZINC Optional 12195 GAUGE OVERLAY- LESCO SETTINGS

22 33117 AGITATOR Standard 12196 GAUGE OVERLAY- EARTHWAY

23 36214 1/4-20 X 1 1/2" PHPMS S.S.

22

5

33

19

20

19

13

14

17

23

39

34

37

35

15

31

18

10

13

44249

27

8

21

1

7

60060RNC
OPTIONAL

Left Side Deflector Kit

14

13

4

F77080 or F77130

32

OPTIONAL

Heavy-Duty

Rain Cover

16

29

6

25

30

11

10

13

3

26

38

2

28

15

18

9

27

12

24

40

19

F80S & F130S CommerCial BroadCast spreader

Key # Part # Description Key # Part # Description

1 12110 IMPELLER 9" ROUND DISHED

2 12147 SPACER (PIVOT LINK) 24 36300 1/4-20 NYLON INSERT LOCKNUT S.S.

3 12148 AXLE BEARING 25 37100 1/4-20 X 1" CARRIAGE BOLT ZINC

4 12152 AXLE BUSHING 26 42256 CONTROL ROD

5 12209 HOPPER BUSHING 27 44249 FRAME BRACE

6 12344 HANDLE SPACER 28 60027 WING NUT ASSEMBLY BLACK

7 24500 AXLE 29 60175-SS UPPER HANDLE SQUARE STAINLESS W/GRIP ea

8 25228 CROSS BRACE 11.25” 30 60298 GAUGE & LEVER ASSEMBLY

9 24111 FRAME 31 60300 PIVOT & BRACKET ASSEMBLY

10 25222-SS LOWER HANDLE 32 70138 PNEUMATIC DRIVE WHEEL STUD

11 25223-SS HANDLE SHAFT 33 F12135 1/4 TURN FASTENER FLEX SELECT

12 25723-SS FRAME FOOT SS 34 F12219 STANDARD OUTPUT FLEX-SELECT SHUTOFF

13 36200 1/4-20 X 1 1/2" HHCS S.S. 35 F13105 FLEX-SELECT 80# HOPPER / F13106 FLEX-SELECT 130# HOPPER

14 36205 1/4-20 X 2 1/4" HHCS S.S. 36 F13130 STANDARD OUTPUT FLEX-SELECT TRAY KIT

15 36216 1/4-20 X 2" HHCS S.S. 37 F40003 SQUARE SCREEN FLEX-SELECT

16 31127 ROD CLIP (Flex-Select) 38 F44251 PIVOT ROD STD OUTPUT FLEX-SELECT

17 31138 #8 X 3/8" PMT #8 HD COARSE BLACK 39 F60333 GEAR BOX ASSEMBLY FLEX -SELECT

18 32100 1/4-20 HEX NUT ZINC 40 43020 BACKPLATE WASHER (FOR F130)

19 32103 1/4-20 NYLON INS LOCKNUT ZINC Optional 60060RNC SIDE DEFLECTOR

20 36103 3/16 X 2" COTTER PIN S.S. Optional HEAVY DUTY RAIN COVER (F77080 for F80 / F77130 FOR F130)

21 36104 3/16 X 1" COTTER PIN S.S. Optional 12195 GAUGE OVERLAY- LESCO SETTINGS

22 33117 AGITATOR Standard 12196 GAUGE OVERLAY- EARTHWAY

23 36214 1/4-20 X 1 1/2" PHPMS S.S.

12209 HOPPER BUSHING

F13130DKIT

STANDARD-OUTPUT PRO

12209 HOPPER BUSHING

33117 AGITATOR

F12135 1/4 TURN

FASTENER

31127 ROD CLIP

F12219D DUAL-PORT PRO

SHUT-OFF ASSY

F44251 PIVOT ROD

STANDARD-OUTPUT

31138 #8 X 3/8

PMT #8HD (BLACK)

F13130HKIT

HIGH-OUTPUT

F12135 1/4 TURN

FASTENER

31127 ROD CLIP

HIGH-OUTPUT

F44251H PIVOT ROD

31135 #8 X 1/2 PHPS (BLACK)

F14102 SHUT OFF

PLATE RETAINER RING

SHUTOFF ASSY

F12219H HIGH-OUTPUT

36208 #6 X 3/8" TYPE

25 PHPS S.S.

F12117 CAM

36107 1/8 X 1 FLAT HD

18-8 SS RIVET

F12111 AGITATOR

PIN RETAINER

12209 HOPPER BUSHING

33117 AGITATOR

F13130KIT

STANDARD-OUTPUT

F12135 1/4 TURN

FASTENER

31127 ROD CLIP

F12219 STANDARD-OUTPUT

F44251 PIVOT ROD

STANDARD-OUTPUT

SHUT-OFF ASSY

31138 #8 X 3/8

PMT #8HD (BLACK)

F13130LKIT

LOW-OUTPUT

12209 HOPPER BUSHING

F12135 1/4 TURN

FASTENER

31127 ROD CLIP

LOW-OUTPUT

F44251L PIVOT ROD

31135 #8 X 1/2 PHPS (BLACK)

SHUTOFF ASSY

F12219L LOW-OUTPUT

F14102 SHUT OFF

PLATE RETAINER RING

F12117 CAM

36107 1/8 X 1 FLAT HD

18-8 SS RIVET

F12111 AGITATOR

36208 #6 X 3/8" TYPE

25 PHPS S.S.

PIN RETAINER

PARTICLE SIZES:

Fine/Small

Medium

Large

10 LBS. 26 18' 5.5m 22 = 2 pass 24' 7.3m 30 = 2 pass 36' 11m

5 LBS> 20 8' 2.4m 30 14' 4.3m

PARTICLE SIZES:

Fine/Small

Medium

10 LBS. 24 16' 4.9m 22 = 2 pass 20' 6.1m

5 LBS. 24 9' 2.7m 30 15' 4.6m

PARTICLE SIZES:

Large  EXTRA LARGE 

10 LBS. 24 28' 8.5m 21 26' 7.9m

Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507

FLEX-SELECT®

BROADCAST SPREADER SETTING MATRIX

GRANULAR MATERIAL

STANDARD- OUTPUT Red Tray

(SAND) (HALF BB) (BB) Ice Melt



LBS. PER 1,000 SPREAD SPREAD SPREAD SPREAD SPREAD SPREAD
SQUARE FEET SETTING WIDTH FT METERS SETTING WIDTH FT METERS SETTING WIDTH FT METERS

1 LB. 7 18' 5.5m 9 24' 7.3m 14 36' 11m
2 LBS. 10 18' 5.5m 13 24' 7.3m 18 36' 11m
3 LBS. 13 18' 5.5m 16 24' 7.3m 23 36' 11m
4 LBS. 14 18' 5.5m 20 24' 7.3m 27 36' 11m
5 LBS. 16 18' 5.5m 22 24' 7.3m 30 36' 11m
6 LBS. 18 18' 5.5m 25 24' 7.3m 23 = 2 pass 36' 11m
7 LBS. 20 18' 5.5m 27 24' 7.3m 25 = 2 pass 36' 11m
8 LBS. 22 18' 5.5m 28 24' 7.3m 27 = 2 pass 36' 11m
9 LBS. 24 18' 5.5m 30 24' 7.3m 28 = 2 pass 36' 11m





GRASS SEED

LBS. PER 1,000 FINE SPREAD SPREAD COARSE SPREAD SPREAD
SQUARE FEET SETTING WIDTH FT METERS SETTING WIDTH FT METERS

2 LBS. 14 8' 2.4m 22 14' 4.3m
3 LBS. 16 8' 2.4m 25 14' 4.3m

4 LBS> 18 8' 2.4m 28 14' 4.3m

GRANULAR MATERIAL

LOW-OUTPUT Black Tray

(SAND) (HALF BB)



LBS. PER 1,000 SPREAD SPREAD SPREAD SPREAD
SQUARE FEET SETTING WIDTH FT METERS SETTING WIDTH FT METERS

1 LB. 8 16' 4.9m 10 20' 6.1m
2 LBS. 10 16' 4.9m 13 20' 6.1m
3 LBS. 12 16' 4.9m 18 20' 6.1m
4 LBS. 13 16' 4.9m 20 20' 6.1m
5 LBS. 16 16' 4.9m 22 20' 6.1m
6 LBS. 18 16' 4.9m 25 20' 6.1m
7 LBS. 20 16' 4.9m 27 20' 6.1m
8 LBS. 21 16' 4.9m 29 20' 6.1m
9 LBS. 23 16' 4.9m 30 20' 6.1m



GRASS SEED

LBS. PER 1,000 FINE SPREAD SPREAD COARSE SPREAD SPREAD
SQUARE FEET. SETTING WIDTH FT METERS SETTING WIDTH FT METERS

2 LBS. 15 9' 2.7m 21 15' 4.6m
3 LBS. 18 9' 2.7m 24 15' 4.6m
4 LBS. 21 9' 2.7m 27 15' 4.6m

Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the drop holes in the Standard-Output

Tray are fully open when the Rate Control handle is on #30. If

not, please adjust control rod at the pivot to allow for a full open
hopper holes with the handle at position at #30.

Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the drop holes in the

LOW-OUTPUT TRAY

are fully closed when the Rate Control Handle is resting on the

stop #0. If not, please adjust control rod at the pivot to ensure the

shut-off is fully closed with the handle at position at #0. Move
the spreader slightly to confirm the calibration because of the

cam.

GRANULAR MATERIAL

HIGH-OUTPUT Lt. Blue

2-hole Tray

(BB) ROCK SALT

LBS. PER 1,000 SPREAD SPREAD SPREAD SPREAD
SQUARE FEET. SETTING WIDTH FT METERS SETTING WIDTH FT METERS

1 LB. 7 28' 8.5m 8 26' 7.9m
2 LBS. 10 28' 8.5m 11 26' 7.9m
3 LBS. 12 28' 8.5m 13 26' 7.9m
4 LBS. 14 28' 8.5m 14 26' 7.9m
5 LBS. 15 28' 8.5m 15 26' 7.9m
6 LBS. 17 28' 8.5m 16 26' 7.9m
7 LBS. 20 28' 8.5m 17 26' 7.9m
8 LBS. 21 28' 8.5m 18 26' 7.9m
9 LBS. 23 28' 8.5m 19 26' 7.9m

©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc.

Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the drop holes in the
are fully closed when the Rate Control Handle is resting on the

stop #0. If not, please adjust control rod at the pivot to ensure the

shut-off is fully closed with the handle at position at #0. Move
the spreader slightly to confirm the calibration because of the

cam.

HIGH-OUTPUT TRAY

PARTICLE SIZES:

Fine/Small

Medium

Large

49 26 18 5.5 22 x 2 pass 24 7.3 30 x 2 pass 36 11.0

25 20 8 2.4 30 14 4.3

PARTICLE SIZES:

Fine/Small  Medium 

49 24 16 4.9 22 x 2 pass 20 6.1

25 24 9 2.7 30 15 4.6

PARTICLE SIZES:

Large

EXTRA LARGE

49 24 28 8.5 21 26 7.9

Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507

FLEX-SELECT®

Metre

Metre

Metre

GRANULAR MATERIAL

STANDARD-OUTPUT Tray

(SAND) (HALF BB) (BB) Ice Melt

Grams PER Square

5 7 18 5.5 9 24 7.3 14 36 11.0
10 10 18 5.5 13 24 7.3 18 36 11.0
15 13 18 5.5 16 24 7.3 23 36 11.0
20 14 18 5.5 20 24 7.3 27 36 11.0
24 16 18 5.5 22 24 7.3 30 36 11.0
29 18 18 5.5 25 24 7.3 23 x 2 pass 36 11.0
34 20 18 5.5 27 24 7.3 25 x 2 pass 36 11.0
39 22 18 5.5 28 24 7.3 27 x 2 pass 36 11.0
44 24 18 5.5 30 24 7.3 28 x 2 pass 36 11.0



SETTING WIDTH FT METRES SETTING WIDTH FT METRES SETTING WIDTH FT METRES

BROADCAST SPREADER SETTING MATRIX



SPREAD SPREAD SPREAD SPREAD SPREAD SPREAD



GRASS SEED

Grams PER Square

10 14 8 2.4 22 14 4.3
15 16 8 2.4 25 14 4.3
20 18 8 2.4 28 14 4.3

FINE SPREAD SPREAD COARSE SPREAD SPREAD

SETTING WIDTH FT METRES SETTING WIDTH FT METRES

GRANULAR MATERIAL

LOW-OUTPUT Black Tray

(SAND) (HALF BB)

Grams PER Square

5 8 16 4.9 10 20 6.1
10 10 16 4.9 13 20 6.1
15 12 16 4.9 18 20 6.1
20 13 16 4.9 20 20 6.1
24 16 16 4.9 22 20 6.1
29 18 16 4.9 25 20 6.1
34 20 16 4.9 27 20 6.1
39 21 16 4.9 29 20 6.1
44 23 16 4.9 30 20 6.1

SETTING WIDTH FT METRES SETTING WIDTH FT METRES

GRASS SEED

Grams PER Square

Metre

10 15 9 2.7 21 15 4.6
15 18 9 2.7 24 15 4.6
20 21 9 2.7 27 15 4.6

FINE SPREAD SPREAD COARSE SPREAD SPREAD

SETTING WIDTH FT METRES SETTING WIDTH FT METRES

SPREAD SPREAD SPREAD SPREAD

Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the drop holes in the

are fully open when the Rate Control handle is on #30. If

Tray

STANDARD-OUTPUT

not, please adjust control rod at the pivot to allow for a full open

hopper holes with the handle at position at #30.

Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the drop holes in the

LOW-OUTPUT TRAY

are fully closed when the Rate Control Handle is resting on the
stop #0. If not, please adjust control rod at the pivot to ensure the

shut-off is fully closed with the handle at position at #0. Move

the spreader slightly to confirm the calibration because of the
cam.

GRANULAR MATERIAL

HIGH-OUTPUT Lt. Blue

2-hole Tray

(BB) Ice Melt ROCK SALT

Grams PER Square

Metre

5 7 28 8.5 8 26 7.9
10 10 28 8.5 11 26 7.9
15 12 28 8.5 13 26 7.9
20 14 28 8.5 14 26 7.9
24 15 28 8.5 15 26 7.9
29 17 28 8.5 16 26 7.9
34 20 28 8.5 17 26 7.9
39 21 28 8.5 18 26 7.9
44 23 28 8.5 19 26 7.9

©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc.



SPREAD SPREAD SPREAD SPREAD

SETTING WIDTH FT METRES SETTING WIDTH FT METRES



Calibration: Start by ensuring that your spreader calibration is
correct. Make sure the 2 drop holes in the

HIGH-OUTPUT TRAY

are fully closed when the Rate Control Handle is resting on the
stop #0. If not, please adjust control rod at the pivot to ensure the

shut-off is fully closed with the handle at position at #0. Move

the spreader slightly to confirm the calibration because of the