Earthway 2170PRO User Manual
2170Pro Broadcast sPreader
EV-N-SPRED
EV-N-SPRED
EarthWay
EarthWay
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsuPPort@earthway.com SKYPE: EARTHWAY.TECH
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must
turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller after each use as some
fertilizer may become stuck on the impeller blades and will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds will change
the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your spreader thoroughly after each
use. To prevent rust, please coat all metal surfaces, also inside tubes where possible, with a light oil or WD-40. Wash between the shut
off plate and bottom of the hopper.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
; If you must use Rock Salt remove the agitator to prevent damage to the gearbox and remove salt from the hopper daily. Rock Salt
will reconstitute back into a solid block over night with humidity and will damage your spreader.
IF YOUR SPREADER COMES SEMI ASSEMBLED, SKIP TO STEP #7
R
R
36200
Qty 4
32100
Qty 2
12148
Qty 2
36216
Qty 5
36300
Qty 6
36105
Qty 1
36103
Qty 1
36205
Qty 2
33117
Qty 1
36210
Qty 2
36214
Qty 4
12152
Qty 2
1. Remove and identify all loose parts from carton.
(Qty 4 #36300)
1/4-20 SS Locknut
36104
Qty 1
ROCK SALT and POWDERED
MATERIALS should not be used in this
spreader as it will damage gearbox and can
void warranty.
Use only granular materials.
13
23
12
11
28
26
16
31
24
17
vvvvvvvv
vvvvvvvv
9
25
(Qty 4 #36214)
1/4-20 X 1½”
Phillips Panhead
2. Position hopper on side. Install frame using (4) 1/4-20 x 1-1/2” Pan Head
Phillips bolts and (4) 1/4-20 nylon insert locknuts. First put bolts through
holes in frame then through holes in bottom of hopper. Secure with locknuts.
TIGHTEN THESE LOCKNUTS NOW
DO NOT TIGHTEN WITH POWER TOOLS
1-2012 Pt# 52166 PAGE 1
Impeller
EarthWay
EV-N-SPRED
®
Notch
Pinion
Shaft
1/8 x 1-1/4”
Cotter Pin (#36105)
Cross Brace
Gearbox Brace
COAST WHEEL
HOLE
DRIVE WHEEL
T
N
O
R
F
HOLE
Gearbox & Axle Assembly
3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin
through impeller then through pinion shaft. Use hole closest to the
gear box. Spread cotter pin to prevent from falling out. Next insert
Cross Brace thru the Gearbox Brace as shown above.
Axle Bearing
Coast wheel side
Flat
Side
1/4-20 x 1-1/2”
Hex Head Bolt
EV-N-SPRED
®
EarthWay
4. Install gear box by inserting the pinion shaft into hole in
center of hoppers bottom. The word “FRONT” on the gearbox
must point to Front of the hopper. Follow label instructions on
hopper.
Drive wheel side
Gearbox & Axle Assembly
Frame brace
Dimples
Cross Brace
Frame
5. Install axle bearings to both lower handles.
NOTE: Notch on bearings and lower
handles. Bearings must go through at side
of lower handle.
NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP.
Step 6B
Step 6C
Impeller
1/4-20 x 1-1/2”
Pan Head Bolt
Lower Handle
1/4-20 x 2-1/4”
Hex Head Bolt
Step 6A
1/4-20 Locknut
Shut-Off
Pivot Rod
6. A - Install lower handles onto axle to both sides as shown. Insert 2¼” bolt through second
hole in lower handle and through rst hole in frame and install locknut. DO NOT TIGHTEN.
B - Now insert 1½” bolt through rst hole in lower handle. Then through frame brace.
NOTE: Dimples on frame brace must be facing toward gear box as shown. Next into threaded
connector in cross brace. DO NOT TIGHTEN.
C - Next insert 1½” bolt through other end of frame brace and through second hole in frame
install locknut.
DO NOT OVER TIGHTEN.
PAGE 2
Loading...