2150T CommerCial Tow
EV-N-SPRED
EarthWay
OVER
3 MPH
Do not tow
faster than
3 MPH
BroadCasT spreader
R
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, EMAIL: TECHSUPPORT@EARTHWAY.COM
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
; If your spreader does not spread evenly, be sure the word “FRONT” on the gear box points toward the tow bar of the
spreader. The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise.
Clean the impeller plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pulled at three miles per hour, which is a brisk walking speed. Slower or faster speeds will
change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your spreader
thoroughly after each use. Coat all metal surfaces (inside & outside of the chassis) with light oil or silicon spray to help
prevent corrosion. Wash between the shut-off plate and bottom of the hopper.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
33117
Qty 1
32100
Qty 2
32103
Qty 10
12152
Qty 2
1. Remove and identify all loose parts from carton.
31104
Qty 4
12148
Qty 2
(Qty 4) #31104
Flat Head Screw
31100
Qty 7
#14 X 1-1/2”
31114
Qty 3
31106
Qty 3
36105
Qty 1
33109
Qty 1
33108
Qty 1
30
ROCK SALT and POWDERED
MATERIALS should not be used in this
spreader as it will damage the gearbox and
can void the warranty.
Use only granular materials.
28
13
12
22
vvvvvvvv
vvvvvvvv
18
15
14
9
21
6
7
10
2. Position hopper on side. Install frame using (4) #14 x 1½” Flat Head Phillips
screws. TIGHTEN THESE NOW
12-2011 Pt# 52158 PAGE 1
Pinion
Notch
Shaft
⅛ x 1¼”
Cotter Pin (#36105)
COAST WHEEL
HOLE
Cross Brace
Gearbox Brace
DRIVE WHEEL
HOLE
Impeller
Gearbox & Axle Assembly
3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin through
impeller then through pinion shaft. Use hole closest to the gear box. Spread
cotter pin to prevent from falling out. Next insert the Cross Brace through the
Gearbox Brace as shown above.
Axle Bearing
4. Install gear box by inserting the pinion shaft into hole in center of
hoppers bottom. The word “FRONT” on the gearbox must point to
Front of the hopper. Follow label instructions on hopper.
Gearbox &
Axle Assembly
Drive wheel side
Front
Coast wheel side
Flat
Side
5. Install axle bearings to both lower
handles. NOTE: Notch on bearings and
lower handles. Bearings must go through
at side of lower handle.
6. A - Install lower handles onto axle
1/4-20 x 1½”
Hex Head Bolt
Step 6B & 6C
1/4-20 x 2¼”
Hex Head Bolt
Step 6A
FRONT
Cross Brace
Impeller
Shut-Off
1/4-20 Locknut
Pivot Rod
Dimples
Frame brace
Frame
#14 x 1½”
Flat Head Screw
Lower Handle
to both sides as shown. Insert 2¼” bolt
through second hole in lower handle and
through rst hole in frame install locknut.
DO NOT TIGHTEN.
B - Now insert 1½” bolt through rst hole in lower handle. Then through frame brace. NOTE: Dimples on frame brace must be facing
toward gear box as shown. Next into threaded connector in cross brace. DO NOT TIGHTEN.
C - Next insert 1½” bolt through other end of frame brace and through second hole in frame install the second cross brace - this one has a
cross hole in the center of the tube.
NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP.
DO NOT OVER TIGHTEN.
PAGE 2
S
2” Cotter Pin
1” Cotter Pin
L
I
Axle Bushing
D
E
Gearbox &
Axle Assembly
Lower
Handle
Frame
Brace
Cross Brace
7. Slide axle bushing over axle and into axle bearing to both sides as shown.
8. Install drive wheel to axle using pin hole nearest to lower handles as shown.
Insert 2” cotter pin through wheel and through axle. Bend with pliers to prevent pin from falling
out.
9. Install coast wheel to axle using outside pin hole. As shown, insert 1” cotter pin through axle
(not thru the wheel). Bend with pliers to prevent pin from falling out.
TURN SPREADER UPRIGHT ON TO WHEELS.
10. Insert pivot rod into shut off plate as shown. Turn to lock in place.
11. Insert other end of pivot rod into pivot and bracket assembly as shown. Turn to lock in place.
12. Install Control Support between lower handles as shown inserting (2) 1¾” bolts thru the Pivot Bracket and the Lower Handles and
secure with (2) lock nuts. Next, line up the hole in the Cross Brace with the hole in the Control Support. Insert 1-4-20 X 2¼” bolt through
the Control Support and thru the hole in the Cross Brace, secure with a 1/4-20 lock nut. Now determine if you want to add the Hitch
Extension to the Control Support use the existing 1/4-20 x 1½” bolt & lock nut to attach the extension tube, and use the new 1/4-20 x 1¾”
bolt & lock nut to attach the Hitch Plates.
13. Attach Gauge & Lever assembly to Control Support using (2) 1/4-20 X 1½” bolts and (2) 1/4-20 lock nuts and TighTen.
1/4 - 20
Lock Nut
1/4 X 1¾”
1/4 X 1½”
Hex Head Bolt
1/4 X 1½”
Hex Head Bolt
Pivot Rod
with extra bend
1/4 X 1¾”
Hex Head Bolt
Shut-Off
Plate
Rotate
Pivot
1/4 - 20
Lock Nut
0
3
5
1
0
1
5
Hex Head Bolt
1/4 X 2¼”
Hex Head Bolt
1/4 - 20
Lock Nut
1/4 - 20
Lock Nut
Hitch Extension
Hitch Plates
PAGE 3
GAUGE & LEVER
ASSEMBLY
Gauge Setting
Overlay
14. Install (1) 1/4-20 regular hex nut
(not a locknut) on to control rod as
shown.
Control Rod
Tabbed Hole
Lever Tensioning Nut
15. Install attened end of control rod in to lever on gauge as shown. Turn to lock
in place. Next push lever forward to setting “0”. Align control rod with hole
Control Rod
Pivot
Rod
Pivot
Bracket
¼-20
Hex Nuts
Control
Rod
in pivot bracket, pull lever backward to insert control rod through hole in pivot
bracket. Now install 1/4-20 regular nut on to control rod.
16. Pull lever back to setting “30” as shown. Next push pivot & bracket forward so that the shut off plate in the hopper is in the full open
position. REMEMBER SETTING “30” ON THE FLOW CONTROL LEVER MUST PLACE THE SHUT-OFF PLATE IN THE FULL
OPEN POSITION TO BE PROPERLY CALIBRATED. Now tighten the nuts against the pivot bracket to prevent change in calibration.
17. Tension on the ow control lever may be adjusted by tightening or loosening the tension nut as shown.
PAGE 4
18. Insert agitator to pinion shaft on inside of hopper. Note: the position of at
side of the agitator. This pin should be installed as shown.
5-YEAR LIMITED WARRANTY
Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years to the end user
with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc. at its discretion will repair or
replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering,
or normal wear and tear as determined by Earthway. Earthway at its discretion may require that the part(s) or product be returned along
with the original purchase receipt at owners’ expense for examination and compliance with the terms of this warranty. Do not return any
product without rst receiving authorization from Earthway Products, Inc. To seek remedy under this warranty, contact Earthway Products,
Inc. at 574-848-7491, techsupport@earthway.com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe
the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges
associated with repair or replacement of non-conformances are specically excluded. Due to the corrosive nature of most fertilizers and ice
melt products, Earthway Products, Inc. makes no warranty against and specically excludes part(s) or product degradation or failure due to
corrosion or its effects. Clean and dry your spreader thoroughly after each use, as a preventative measure, coat all metal parts (inside and
outside of the steel tubing) with a light oil or silicon spray.
OPERATING INSTRUCTIONS
HOW TO ORDER SPARE PARTS
All spare parts listed herein may be ordered direct from the
manufacturer. Be sure to give the following information when
ordering.
; Model Number
; Part Number
; Part Description
You can contact us by calling (574) 848-7491 or 800-294-0671
to place an order with a credit card.
Questions? parts@earthway.com
Before lling hopper, become familiar with the operation of this
spreader.
1. Obtain proper setting for material to be used from the RATE
SETTING CHART included with this spreader.
2. Move stop bolt on rate gauge assembly to the proper setting.
3. While pushing spreader forward, pull control lever back to
stop bolt.
4. To stop, push lever forward to close ow holes before you stop
moving.
5. When nished, empty any remaining material from hopper.
6. Thoroughly wash spreader and allow to dry before storing.
Light oiling can prevent corrosion.
The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of
material applied, walking/towing speed, and roughness of ground surface may require slightly different spreader settings.
Due to the above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the
settings listed.
Full Rate Path
Half Rate Path
Finish
Finish
Start
Start
PAGE 5
16
30
35
11
Earthway Products, Inc.
P.O. Box 547
Bristol, IN 46507
8
7
Heavy-Duty Rain Cover
25
6
77001
OPTIONAL
60043R
OPTIONAL
29
11
21
37
38
36
16
31
3
32
22
Heavy-Duty
Rain Cover
&
Side Deflector Kit
16
24
33
5
5
9
11
25
20
11
13
8
9
17
10
12
16
17
16
15
11
23
16
15
14
34
18
26
17
27
16
1
4
3-Side Deflector Kit
Phone: 800-294-0671
www.earthway.com
60166R
OPTIONAL
26
27
1
19
2
28
a
y
W
h
S
t
e
r
t
a
E
t
i
n
g
s
0
2
0
1
3
0
0
Standard Settings Gauge Overlay #12196 and
OPTIONAL Lesco Settings Gauge Overlay #12195
2150T Broadcast Tow Spreader ~ Parts List
Key # Part # Description Key # Part # Description
1 70138 PNEUMATIC DRIVE WHEEL STUD 20 11927 SHUTOFF SUPPORT- LARGE
2 33109 3/16" X 2" COTTER PIN ZINC 21 60298 GAUGE & LEVER ASSEMBLY
3 33117 AGITATOR 22 42263 CONTROL ROD
4 33108 3/16" X 1" COTTER PIN ZINC 23 31138 #8 X 3/8" PMT #8 HD COARSE BLACK
5 12317 SHUT OFF PLATE (2600B) BLACK 24 36208 #6 X 3/8" TYPE 25 PHPS S.S.
6 44251 PIVOT ROD 25 32100 1/4-20 HEX NUT ZINC
7 60300 PIVOT & BRACKET ASSEMBLY 26 12148 AXLE BEARING
8 31114 1/4-20 X 1 3/4" HHCS ZINC 27 12152 AXLE BUSHING
9 25207 LOWER HANDLE 28 60331 GEAR BOX & AXLE ASSEMBLY
10 22601 UPPER CROSS BRACE 29 19113 1.0" OD HOLE PLUG BLACK
11 32103 1/4-20 NYLON INS LOCKNUT ZINC 30 44215 HITCH PLATE
12 25108 FRAME 31 40002 ROUND SCREEN
13 25603 CONTROL SUPPORT 32 60332 HOPPER ASSEMBLY
14 25228 CROSS BRACE 11.25” 33 12220 GEAR BOX BUSHING
15 44249 FRAME BRACE 34 31104 #14 X 1 1/2 TYPE 25 FHPS ZINC
16 31100 1/4-20 X 1 1/2 HHMS ZINC 35 77051 HITCH EXTENSION KIT
17 31106 1/4-20 X 2 1/4" HHCS ZINC 36 60027 WING NUT ASSEMBLY BLACK
18 12109 IMPELLER (9" DIA) 37 37100 1/4-20 X 1" CARRIAGE BOLT ZINC
19 36105 1/8" X 1 1/4" COTTER PIN S.S. 38 12147 SPACER
o
c
S
s
e
e
t
L
t
i
n
g
s
0
3
2
0
1
0
0
Loading...