Earthway 2100P User Manual
2100P EstatE
EarthWay
Broadcast sPrEadEr
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, Email: tEchsuPPort@Earthway.com
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The
impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller
plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your
spreader thoroughly after each use. A coating of light spray oil will help prevent corrosion. Wash between the shut off
plate and bottom of the hopper.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
EV-N-SPRED
®
¼-20 x
⅛ x 1¼”
Cotter Pin
¼-20 x
2” Bolt
Lower
Housing Clip
Axle
Washer
#10 x ⅝”
Screw
Bushing
¼-20
Lock Nut
Agitator
Axle
Bearing
#12 x 1¼”
Flat Head Screw
¼-20
Hex Nut
Axle
Cotter Pin
¼-20 x
1¼” Bolt
⅛ x ¾”
1½” Bolt
1. Remove and identify all loose parts from carton.
(Qty 4) #31105
#12 X 1¼”
Flat Head Screw
2. Position the Hopper on its top as shown
to the left. Install frame using (4) #12 x
1¼” Flat Head Phillips screws. TIGHTEN
THESE NOW - use care to not over tighten
⅛ x 1¾”
Cotter Pin
¼-20 x 1¾”
Carriage Bolt
FRAME
IMPELLER
CONTROL
ASSEMBLY
AXLE
UPPER HANDLE
ASSEMBLY
DRAW BAR
&
BRACE ASSEMBLY
GEARBOX
10-18 Pt# 52159 PAGE 1
Pinion
Shaft
N
O
R
F
⅛ x 1¼”
Cotter Pin
T
Impeller
Gearbox Assembly
3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” Cotter pin
through impeller then through pinion shaft. Use hole closest to the
gear box. Spread cotter pin to prevent from falling out.
Axle Bearing
4. Install gear box by inserting the pinion shaft into hole in center of hoppers
bottom. The word “FRONT” on the gearbox must point to Front of the
Notch
hopper. Follow label instructions on hopper. Next, slide axle thru the gearbox
with the drive wheel hole positioned as shown in the drawings below.
SLIDE
NT
O
R
F
Gearbox
FRONT
Flat
Side
5. Install axle bearings to both Drawbars.
NOTE: Notch on bearings and in the
Drawbar line up. Bearings must go through
at side of lower handle.
COAST WHEEL SIDE
¼-20 x 1¼”
Hex Head Bolt
¼-20 x 2”
Hex Head Bolt
Gearbox Assembly
Impeller
¼-20 Locknut
DRIVE WHEEL SIDE
Frame brace
Frame
Flat Head
Screw
Draw Bar
Shut-Off
PAGE 2
6. Install lower handles onto axle to both sides as shown. Insert ¼-20 x 2” bolt through hole
in Draw Bar and through rst hole in frame install locknut. DO NOT TIGHTEN. Next insert
¼-20 x 1¼” bolt through frame brace and through second hole in frame install locknut.
NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST
STEP. DO NOT OVER TIGHTEN.
Loading...