Earlex Pure Steam Cleaner User Manual

SAFETY & OPERATING INSTRUCTIONS

Thank you for purchasing the Earlex Pure Steam Cleaner. In order to obtain the

best results, please read the instructions before commencing any work.

RETAIN FOR FUTURE REFERENCE

 Keep equipment away from children

and pets.

 Ensure boiler is placed on a flat level

surface, and should the boiler
become tilted in use - level again
immediately. Failure to do so can
result in severe over heating,
complete element failure and void
your guarantee.

 Block boiler unit securely if using on

stairs.

 The boiler becomes hot in use. Move

only by using the carrying handle.

 Steam is produced at 100˚C. Be

careful, wear protective clothing and
protect your hands with heat resistant
gloves or mitts.

 Never point hose or accessories at

anyone.

 Never remove filler cap or detach hose

whilst unit is operating.

 Never block the safety valve.
 Never use outside when raining.
 Switch off and wait for 2 minutes

before removing filler cap to refill
boiler.

 Do not overfill.
 Allow to cool completely before

emptying boiler.

 Do not stand on boiler or hose.
 Do not drag or try to move boiler by

pulling the mains lead.

 Do not allow water or steam to enter

light switches and power points.

 Do not leave the unit unattended.
 Use only standard tap water. Never

add detergents or chemicals.

 Extreme care must be taken if the

unit is used in bathrooms. Always be
aware of danger of electrocution from
stored water in baths and sinks.

 Never change the accessories when

the unit is operating.

 Always store upright.
 It is recommended that a RCD (residual

current device) rated at 30mA is fitted
into the mains supply socket for added
protection against electric shock.

 Use only genuine Earlex replacement

parts

SAFETY RULES

IMPORTANT NOTE

Always check the suitability of materials before steam cleaning and do not use this product on
Draylon®or similar materials. Some carpets have stain-resistant treatments which can break down

so always test a small area first to make sure that there are no unusual effects. Do not soak materials
being cleaned. Only light application of steam is required.
The boiler has been designed for safe use but the user must be acutely aware that at all times steam
is being produced, and steam is hot, so be careful, wear protective clothing and protect your hands
with heat resistant gloves or mitts.
Pure Steam will clean most types of surfaces with the power of steam. The individual tools are
specifically designed for different applications. These tools are illustrated on page 3.
Pure Steam does not require detergents, chemicals or other cleaners, it cleans naturally with the
action of steam. This powerful action also removes any traces of powder or liquid cleaners or
detergents that have been previously used.

SAFETY CUT- OUT

A safety cut-out is fitted to prevent overheating of the element if water boils below the min. level.
If unit stops boiling during use this may be the cause. Wait for 2 minutes before removing filler cap then
re-fill with water. The cut-out will self reset and steam be produced again within 19 minutes.

The cut-out will not protect the element if a part filled unit is tilted during use in a way which
enables part of the element to be out of the water for longer than 15-20 seconds.

CHANGING TOOLS

Never remove the hose or change tools when the unit is plugged in. Wait 2 minutes after unplugging
before changing tools. Screw the nut, which is on the end of the steam hose, onto the outlet of the tool

- hand tight only.

PROTECT YOUR HOME!

The heat generated by the boiler unit can mark carpets, soft furnishings, table tops, cabinets etc.
To prevent this we recommend placing the unit on a wooden board, tray or other barrier - making sure
it will not slip off one side or tilt during use.
Dust sheets or newspapers are not suitable heat protectors for delicate surfaces.

a. Boiler F78

b Floor Cleaning Tool AC254

cTowel for Floor Cleaning Tool AC275

d Upholstery Cleaning Tool AC250

eTowel for Upholstery Cleaning Tool AC276

fWindow/Tile Cleaner AC258

g Jet Nozzle AC262

h Scraper AC21

i Brush AC25

j Long Handle (3 tubes) AC01

k Universal Handle AC302

l 3.65 metre Steam Hose ST94

m Castors (not shown) F17

n3 Metre Cord Set (not shown) B17

COMPONENT LIST

a

b

c

d

e

f

g

h

i

j

k

l

ASSEMBLING THE ACCESSORIES

The Universal Handle is used in conjunction with the Floor Cleaner, Upholstery Cleaner, Window / Tile
Cleaner and Jet Nozzle. Align the outline triangle on the handle with the triangle on the accessory.
Push the handle into the accessory and twist so that the solid triangles on the handle and accessory
are aligned (Fig.1).
Over time, you may find that your steam cleaning accessories become awkward to assemble to the
universal handle. This is due to the steam reducing the lubrication properties of the ‘O’ ring seals. In
this event, simply lubricate the ‘O’ ring seals as illustrated (Fig.2) using washing-up liquid or furniture
polish.
The Long Handle Attachment is designed to be used when cleaning floors or hard to reach areas. To
assemble, pass hose through each of the long handle sections, in at the small end out at the large end.
Screw the hose nut onto the universal handle and push the
long handle tube sections together and onto the taper on the

universal handle (Fig.3). You can use
one, two or three sections of the long
handle. Disconnect in reverse order.
If you have any difficulty in
disconnecting twist the handles
apart.

Fig.1

Assembling
Universal
Handle

Fig.2 Seal Lubrication

CASTORS

The castors are packed separately. Turn the boiler upside down and insert the 3 castors. These should
be pushed in hard until they stop. Once installed these remain in place permanently.