Page 1
Box contents
2
• Please see the back of the manual for
optional accessories.
• If you have any questions, please call
the Dyson helpline on 08705 275104
or log on to www.dyson.co.uk
Important information
Hose
Wand release
On/off switch
Cyclone release catch
and bin emptying trigger
Stair tool
Airway inspection valve
Valve release clips
Soleplate
Shroud
Brush tool Crevice tool
Wand cap
Upper cable winder
Lower cable winder
U bend release clip
Airway inspection (U bend)
Wand
Brushbar on/off
(not steel/yellow model)
Hose release
Optional: Mini
turbine head
Filter release catch
H: 210mm
W: 297mm
JN: 1072 DC14 UK OP MAN DATE: 23.04.04 SPEC: CMYK + 877 PROG(CR): 03 PROG(CL): 05STUDIO: JH/CC INFO:
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 1
Page 2
Assembling your Dyson
3
• Ensure the wand cap cover is
closed.
• Ensure hose is kept straight when
inserting wand into hose.
A Slide hose into runners at back
of machine and click into place.
B Slide wand straight down in to
hose until it clicks into place.
Click wand handle into top
of machine.
Click tools into place. Wind cable anti-clockwise around
cable winders and secure with clip.
Important information
A
B
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 2
Page 3
Using your Dyson
4
• Do not press the cyclone release
catch whilst carrying the machine.
• Ensure the cyclone pack is secured
to the machine.
• Do not shake the machine
whilst carrying.
• Keep hair and loose fabrics away
from wand cap when machine is on.
Anti-jam brushbar
(not steel/yellow model)
DC14 steel/yellow is not suitable for
hard floors, as the brushbar cannot
be turned off.
We recommend brush control
models for homes with mixed
flooring.
Ensure the machine is in an upright
position before adjusting the setting.
Press on/off button1, push cleaner
head down with foot and pull
handle towards you.
Use the carry handle to lift
the machine.
Tools
A Push back wand cap.
B Pull wand from inside wand
handle until it locks into place.
C Press button to release hose and
wand handle from machine.
D To push wand back inside hose,
ensure hose is straight. Press the
release catch and push wand
back inside wand handle.
Important information
A
B
C
• The machine is intended for
domestic use only.
• Fine dust such as plaster dust
should only be vacuumed in very
small amounts.
For hard floors
For carpets
D
1
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 3
Page 4
Using your Dyson
5
• Powerful suction can cause the
hose to ‘pull back’ in use – please
take care when cleaning stairs.
A Tools can be fitted directly to the
end of the wand and hose for
hard to reach places.
B With wand extended, press side
buttons to remove wand handle
from the hose.
C The tools can be fitted directly to
the end of the hose.
Always work with the machine at
the bottom of the stairs.
Important information
A
C
B
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 4
Page 5
Emptying the clear bin
TM
6
• Turn power off and unplug before
emptying the bin.
• Do not use the machine without
the clear binTMin place.
Empty the clear bin
TM
as soon as the
MAX mark is reached. Press catch
1 to release cyclone from machine.
Option A
Push the button as shown to
release the bin base and empty
directly into dustbin.
Option B
Emptying in a bag is
recommended for allergy sufferers.
Place bin in bag and pull trigger to
release bin base.
Let the dust settle, close bin
base securely before removing
from bag.
Close bin base securely and place
back onto machine.
Important information
The British Allergy Foundation
considers that this product may in
proper use reduce exposure to
both House Dust Mite (Der p 1)
and Cat Allergen (Fel d 1). It is strongly recommended
that a sensitive person should take care when emptying
the clear binTM. We recommend the manufacturers’
emptying instructions should be strictly followed.
Assessment carried out by BAF indicate that an
individual’s exposure can be reduced but this does not
mean that an individual’s allergic symptoms will
necessarily diminish. BAF’s opinion applies only to the
products and allergen stated. The product should be
used only for its intended purpose and strictly in
accordance with the manufacturers’ instructions at all
times.
Exposure to allergens can be dangerous. If you believe
that you may suffer from an allergy you should seek
medical advice. The British Allergy Foundation is a
national charity (Charity Reg. No. 1003726) founded in
1991 with the aim of improving awareness, prevention
and treatment of allergy.
The Foundation continually strives to help sufferers to
help themselves, often seeking to avoid or reduce
exposure to relevant allergens. The Seal of Approval
scheme forms a part of this initiative.
1
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 5
Page 6
Cleaning the clear bin
TM
7
• Do not use detergents,
polishes or freshening
products.
• Do not immerse the cleaner
in water.
• Ensure the bin is completely dry
before refitting.
Cleaning the shroud (if necessary)
Ensure the bin has been emptied and
bin base is open.
Press catch 1 to release clear binTM.
Clean shroud with a cloth or small
brush to remove fluff or debris.
Cleaning the clear bin
TM
• Do not use detergents, polishes
or freshening products.
• Do not immerse the whole
cleaner in water.
• Ensure the bin is completely dry
before refitting.
Replacing the shroud
A Hold the carry handle and place
the cyclone into the clear binTM.
B Line up the catches and push
down to click in to place. Ensure
the clear bin
TM
is secure before
replacing on the machine.
Important information
1
A
B
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 6
Page 7
Washing the filter at
least every 6 months
8
Turn power off and unplug before
emptying the bin.
Do not use the machine without
the filter in place.
Do not use detergent.
Do not put the filter in the
dishwasher, washing machine,
oven, tumble dryer, microwave or
near a naked flame.
The filter may require washing
more frequently if vacuuming fine
dust. Press catch 1 to release
cyclone pack.
Accessing the filter
Lift filter release catch 2 and
remove filter from machine.
B Wash filter and case until water
runs clear.
C Dry for at least 12 hours.
Ensure filter and case are
completely dry before refitting
onto the machine.
Important information
2
A
B
C
A Washing the filter
• Wash filter and case in cold water only.
• Only wash blue foam and yellow cage.
• Do not use detergent.
• Do not put in washing machine or
dishwasher.
• Do not put the filter in the dishwasher,
washing machine, oven, tumble dryer,
microwave or near a naked flame.
1
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 7
Page 8
Finding blockages
9
Turn power off and unplug before
emptying the bin.
If any part of your machine
becomes blocked, it may overheat
and then cut out. Unplug machine
and leave to cool down.
Please note: Clearing blockages is
not covered by your machine’s
guarantee. (Keep your proof of
purchase safe.)
Beware of sharp objects when
clearing blockages.
Secure all parts before using
the machine.
The ratchet noise warns you that
the brushbar is obstructed.
Disconnect the machine before
removing the obstruction.
Check tools are clear of blockages. A Remove wand and check inside
wand and hose for blockages.
B Press hose release button at front
of machine and slide hose out
with lower cable winder at rear.
U bend inspection
C Tilt machine forward, slide out
U bend and check inside
for blockages.
Airway inspection
D Squeeze valve release catches and
check inside for blockages.
Brushbar obstructions
Lie cleaner on its front.
Undo fasteners using a coin and
remove soleplate.
Remove fluff and hair from brushbar.
Replace soleplate and tighten
fasteners.
Important information
A
B
C
D
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 8
Page 9
Changing/fitting the belt
(steel/yellow model only)
10
Turn power off, unplug machine
and allow machine to cool for 1
hour before changing/fitting belt.
Ensure soleplate is in correct
position before use.
Remove wand and turn machine
upside down.
A Undo fasteners using a coin,
slide back end caps and remove
soleplate.
B Remove dirt or debris and check
spindle is clean.
C To replace the belt, remove the
brushbar, loop belt around
brushbar and feed through hole.
D Check end caps are in place.
Important information
A
B
C
D
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 9
Page 10
Changing/fitting the belt
(steel/yellow model only)
11
E Use back of cleaner as lever,
loop belt around thumb. Turn the
belt 90 degrees, stretch and
release over spindle.Belt must be
free of twists as shown.
F Rest the three tabs on inside of
yellow bumper strip and secure
soleplate back into position.
G Ensure soleplate is in correct
position before use.
Optional: Mini turbine head
A Release catches and remove
the soleplate.
B Remove both brushbars and
clear away thread and hair.
C To reassemble, match the arrows
on the brushbar to the arrows on
central support.
D Align front of soleplate with front
of tool and secure all 3 catches.
E Ensure slider is set as shown.
Important information
Ensure soleplate is in correct
position before use.
A
B D
C
Optional: maintaining the Mini turbine head
E
E
F
G
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 10
Page 11
Dyson customer care
12
If you have a query about your Dyson, call the
Dyson helpline with your serial number (found
underneath your machine).
Important Information
Check that your electricity supply corresponds
to that shown on the rating plate. The machine
must be used as rated.
If the supply cord or the appliance is damaged,
disconnect from the socket outlet immediately.
The supply cord must be replaced by Dyson
Ltd or our appointed agent to avoid a hazard.
This appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
Do not use the cleaner if the cable or plug are
damaged or if the cleaner has been damaged,
dropped or has come in to contact with water
or any other liquid. In these cases, contact the
Helpline.
When vacuuming, certain carpets may generate
small static charges in the clear bin. These are
entirely harmless and not associated with the
main supply. To minimise any effect from this,
do not put your hand or insert any object in to
the clear bin unless you have emptied it and
rinsed it out with cold water.
Do not use the cleaner if any parts appear to
be faulty, missing or damaged.
Do not carry out any maintenance work other
than that shown in this manual or advised by
the Helpline and do not put anything in to the
openings or moving parts of the machine.
Only use parts recommended by Dyson; failure
to do so could invalidate your guarantee.
European conformity information
A sample of this product has been tested and
found to be in conformity with the following
European Directives: 73/23/EEC Low voltage
(safety) Directive, 93/68/EEC CE Marking
Directive, 89/336/EEC EMC Directive.
US10/468,870
JP2002-567124
EP1361812
AU2002-567124
GB2393383
PCT/GB2003/00
4058
PCT/GB2003/00
3928
AU744408
EP1119282
JP2000-575411
US6,519,807
AU2002231965
EP1361813
JP2002-567126
US10/468,653
AU744362
EP1121043
JP2000-575409
US6,572,078
AU757043
EP1052923
JP2000-523902
US6,691,849
GB0326102.1
AU2002-226556
EP1370172
JP2002-567120
US10/468,676
AU2002-225207
EP1361814
JP2002-567129
AU2001-240894
EP1268076
GB2360719
JP2001-572220
US10/239,426
AU2002-225232
EP1361815
GB2372435
JP2002-567134
US10/468,304
GB2372436
AU637 272
EP0636338
JP1 948 863
US5,078,761
Important information
PATENTS AND PATENT APPLICATIONS
REGISTERED DESIGNS AND DESIGN APPLICATIONS
AU154578
EP000090865
GB3012888
JP2003-34801
US29/193,623
GB3015739
Do not pull on
the cable.
Do not use above
you on the stairs.
Do not put your
hands near the
brushbar when in use.
Do not use near
naked flame.
Do not leave
cleaner near heat
sources.
Do not pick up
water or liquids.
Do not run over
the cable.
Do not pick up
burning objects.
Dyson Customer Care
Every new Dyson domestic vacuum
cleaner has a 2 year guarantee.
If you have a query about your
Dyson, call the Dyson Customer
Helpline with your serial number
and details of where/when you
bought the cleaner.
Most queries can be solved over
the phone by one of our trained
Helpline staff.
If your cleaner needs attention
from our engineers, we aim to
have it repaired and tested within
3 working days.
Your serial number can be found
on your rating plate which is
underneath the machine beneath
the wheels.
Note your serial number for
future reference:
UK 08705 275 104
7 days a week 8am - 8pm
e-mail: service@dyson.com
Tetbury Hill, Malmesbury, Wilts SN16 0RP
IRL (01) 475 7109
Visit the Dyson website for product information
and to order accessories and spares.
1
2
3
Mini turbine head
For improved pick up of pet-hair
from upholstery and stairs.
Flexi crevice tool
Extends and flexes into
awkward gaps.
Hard floor tool
For improved pick-up on
hard floors.
Cleaning Pack
1. Groomer
Long bristles work zorb carpet
maintenance powder deep into
carpets.
2. Zorb carpet maintenance
(750g)*
Millions of tiny sponges absorb dirt
from the carpet, to keep new
carpets looking new with none of
the drawbacks of wet cleaning.
3. Dyzolv spot cleaner (230ml*)
Contains 4 active agents to clean
spots and spills e.g grease, food,
drinks and soil. Ideal for wool and
stain resistant carpets and rugs.
DC14 accessories
The items can be used with your DC14. For further information visit the
Dyson website www.dyson.co.uk
JN 10072 PN 08447-01-01 07.05.04
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 11
Page 12
User Guide
Please read this carefully before use
10072_DC14_UK_OP_MAN p1-12 5/10/04 10:57 AM Page 12
Loading...