Dynexproducts DX-SP211 Quick Start Manual
Quick Setup Guide I DX-SP211
2-Way Indoor/Outdoor Multipurpose Speakers
Package contents
• 2-way indoor/outdoor speakers (2)
• Mounting brackets (2)
• Knobs (4)
• Mounting screws (8)
• Adhesive-backed cushions for mounting brackets (4)
• Adhesive-backed cushioned feet for speakers (8)
Setting up your speakers
Installing the brackets (optional)
You can connect the speakers to wall-mount brackets for
elevated wall positioning.
Note: If you are positioning the speakers on a shelf or other
surface, attach the provided cushioned feet to the bottom
of each speaker.
1 Secure the wall-mount brackets onto the wall where you
want to mount the speakers. If the location is backed by
wall studs, you can use the wood screws provided. If the
location is backed by only dry wall (gypsum board or
other wall material), use wall anchors (not included).
2 Attach the provided mounting bracket cushions on the
inside of the brackets so they protect the bracket screw
holes.
3 Slide a speaker into each mounting bracket.
4 Line up the screw holes (one on top, one on bottom),
then screw a knob into each hole to secure the speaker
to the bracket. You can loosen the knob to adjust the
direction the speakers are pointing.
Connecting the speakers
For best performance, you must connect the speaker wires
correctly. All two-conductor wire is marked in some way to
help you do this. One side will be marked with a colored
stripe, a raised rib, or a dierent-color conductor. Use the
marked side for the “red” connections.
1 Connect the red speaker terminals to the red (+)
amplier terminals.
2 Connect the black speaker terminals to the black (-)
amplier terminals.
To verify connections:
1 Switch your amplier to MONO and place your speakers
close to each other.
2 Adjust the balance control so that only one speaker is
playing.
3 Listen to the bass level and adjust the balance control so
that both speakers are playing. If the bass decreases
when both speakers are playing, one of the speakers is
connected incorrectly, and the positive (+) and negative
(-) terminals should have the speaker cables reversed.
Adjusting volume
• If you hear distortion, immediately reduce the volume.
Permanent speaker damage can occur within seconds.
Distortion indicates that the amplier or speaker is
operating beyond its design limits. Do not ignore
distortion just because the volume control is not all the
way up. Most ampliers deliver full power when the
volume control is set near the middle of its range. Using
loudness, bass boost, treble boost, or an equalizer can
produce full output at even lower settings, so distortion
is the only true indicator that damage is imminent.
• Almost any speaker can be used with almost any
amplier, but almost any speaker can be damaged by
almost any amplier (despite either unit’s power rating).
Dynex’s power recommendations are accurate only if
our assumptions concerning the amplier, the type of
music, and the conditions of use are correct. Our most
important assumption is that the volume is never set
above the point of distortion.
Positioning your speakers
The performance of your new Dynex speakers, as with any
high-quality system, is inuenced by their placement in
your listening room.
Consider these guidelines as you select the speaker positions:
• Place the speakers so that they face your listening area.
Ideally, the grill fronts (front of the speakers) should be
“aimed” towards ear level.
• If you are installing your speakers outdoors, select
locations facing your listening area that are protected
from rain and snow, and out of direct sunlight.
Maintaining your speakers
• Maintain the nish of your speakers by wiping the
surface with a damp cloth.
• To clean the grilles, you can vacuum them or gently tap
them.
Specications
Design..................................................Weather resistant, 2-way
Woofer.........4" (10 cm) dynamic with polypropylene cone
Tweeter...................................... 2" (5 cm) polycarbonate cone
Impedance ...........................................................8 ohm nominal
Eciency..............................................................84 dB @ 1W-1m
Frequency response............................................. 90 Hz-20 KHz
Amplier power* (min/max) ...........................................5-40W
Enclosure ...........................................................Cast polystyrene
(mounting brackets included)
Product Net Weight..........................................2.09 lbs. (.95 kg)
with bracket..................................................... 2.32 lbs. (1.05 kg)
Product dimensions................ 7.4" × 4.6" × 4.3" (H × W × D)
(18.7 cm × 11.7 cm × 11 cm)
with bracket............................... 8.6" × 4.6" × 5.3" (H × W × D)
(21.9 cm × 11.7 cm × 13.6 cm)
*Power recommendations are based on amplier volume
never being set above the point of audible distortion.
90-day limited warranty
For complete warranty, visit www.dynexproducts.com.
Contact Dynex:
For customer service, call 800-305-2204
www.dynexproducts.com
© 2011 BBY Solutions, Inc. All Rights Reserved. DYNEX is a trademark
of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective
owners.
90-day limited warranty
Dynex Products (“Dynex”) warrants to you, the original
purchaser of this new product (“Product”), that the Product
shall be free of defects in the original manufacture of the
material or workmanship for a period of ninety (90) days
from the date of your purchase of the Product (“Warranty
Period”). This Product must be purchased from an
authorized dealer of Dynex brand products and packaged
with this warranty statement. This warranty does not cover
refurbished Product. If you notify Dynex during the
Warranty Period of a defect covered by this warranty that
requires service, terms of this warranty apply.
How long does the coverage last?
The Warranty Period lasts for 1 year (365 days) from the
date you purchased the Product. The purchase date is
printed on the receipt you received with the Product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of
the material or workmanship of the Product is determined
to be defective by an authorized Dynex repair center or
store personnel, Dynex will (at its sole option): (1) repair
the Product with new or rebuilt parts; or (2) replace the
Product at no charge with new or rebuilt comparable
products or parts. Products and parts replaced under this
warranty become the property of Dynex and are not
returned to you. If service of Products or parts are required
after the Warranty Period expires, you must pay all labor
and parts charges. This warranty lasts as long as you own
your Dynex Product during the Warranty Period. Warranty
coverage terminates if you sell or otherwise transfer the
Product.
How to obtain warranty service?
If you purchased the Product at a retail store location, take
your original receipt and the Product to the store you
purchased it from. Make sure that you place the Product in
its original packaging or packaging that provides the same
amount of protection as the original packaging. If you
purchased the Product from an online web site, mail your
original receipt and the Product to the address listed on the
web site. Make sure that you put the Product in its original
packaging or packaging that provides the same amount of
protection as the original packaging.
To obtain in-home warranty service for a television with a
screen 30 inches or larger, call 1-888-BESTBUY. Call agents
will diagnose and correct the issue over the phone or will
have an Dynex-approved repair person dispatched to your
home. Should the Dynex-approved repair person not
correct the issue on the rst call, an Dynex television (size
and features to be determined by Dynex) will be loaned to
you until your TV is repaired and returned, at no charge to
you. This feature is only available to Dynex television
consumers residing in the United States.
Where is the warranty valid?
This warranty is valid only to the original purchaser of the
product in the United States, Canada, and Mexico.
What does the warranty not cover?
This warranty does not cover:
• Customer instruction
• Installation
• Set up adjustments
• Cosmetic damage
• Damage due to acts of God, such as lightning strikes
• Accident
• Misuse
• Abuse
• Negligence
• Commercial use
• Modication of any part of the Product, including the
antenna
• Plasma display panel damaged by static (non-moving)
images applied for lengthy periods (burn-in).
This warranty also does not cover:
• Damage due to incorrect operation or maintenance
• Connection to an incorrect voltage supply
• Attempted repair by anyone other than a facility
authorized by Dynex to service the Product
• Products sold as is or with all faults
• Consumables, such as fuses or batteries
• Products where the factory applied serial number has
been altered or removed
REPAIR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS YOUR EXCLUSIVE REMEDY. DYNEX SHALL NOT
BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT
LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT,
LOST BUSINESS OR LOST PROFITS. DYNEX PRODUCTS MAKES
NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE
PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR
THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANT
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE WARRANTY PERIOD SET
FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS
OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD.
SOME STATES, PROVINCES AND JURISDICTIONS DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH
VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
ENGLISH 10-1241
Loading...