Dynex DX-SB114 User Manual
Quick Setup Guide
Soundbar Home Theater Speaker | DX-SB114
Congratulations on your purchase
of a Dynex Soundbar Home
Theater Speaker System.
Package contents
Soundbar
Remote control
RCA audio cable
Wall mounting template
AC adapter
3.5 mm audio cable
FEATURES
Top view
Standby
Back view
Remote control
Standard Theater News
DSP
DC IN
18V
SUBWOOFER OUT
SUBWOOFER OUT
Back of the soundbar
DC IN
18V
SUBWOOFER OUT
RCA IN
AUX IN
OPTICAL IN
L
R
Subwoofer cable (not included)
Subwoofer
BASS
VOL
CONNECT THE SOUNDBAR
Choose one connection option below that ts your audio source device (e.g., TV, projector,
DVD/Blu-ray player, gaming console etc.).
CAUTION: Turn o or unplug all devices while you are making connections.
NOTE: If you have multiple devices connected to a TV or projector, connecting directly to the TV or projector will ensure
audio plays through your soundbar from all of your devices.
AUDIO QUALITY
BEST
GOOD
GOOD
JACK TYPE (on source device) CABLE
Digital optical cable (not included)
3.5 mm audio cable (included)
RCA Audio cable (included)
CONNECT THE SUBWOOFER
OPTIONAL
Connect one end of the subwoofer
speaker cable (not included) to the
subwoofer and the other end to the
soundbar.
- PICK ONE -
RCA IN
OPTICAL IN
Digital connections (BEST)
1 Connect one end of the digital optical cable (not included)
AUX IN
L
R
to your soundbar. Connect the other end into the Digital
AUX IN
L
R
DC IN
18V
RCA IN
OPTICAL IN
Optical Output port on your audio source device.
2 Change the device’s audio output to 'PCM' format
TV, projector, or
DVD/Blu-ray player
OUTPUT
DIGITAL
OPTICAL
Back of the soundbar
L
R
DC IN
18V
SUBWOOFER OUT
RCA IN
AUX IN
OPTICAL IN
(typically found in Audio Settings). Refer to the
documentation that came with your audio source device
(e.g., TV, projector, DVD/Blu-ray player, etc.) for more
information.
3 After connecting power, see USING YOUR SOUNDBAR on the
Digital optical cable (not included)
next page.
CONNECT THE AC ADAPTER
CAUTIONS:
• Make sure that the electrical outlet matches the AC adapter’s input requirements of 100-240 V,
50/60 Hz before connecting.
• Use only the AC adapter provided.
• Plug in the AC adapter only after all other connections have been made.
1 Connect the AC adapter to the DC IN jack on the back of the soundbar.
2 Plug the other end of the AC adapter into a power outlet or surge protector.
Back of the soundbar
Before using your new product, please read these
instructions to prevent any damage.
# Item
1 Standby indicator
2 (Power) button
and indicator
Description
Lights when the soundbar is in standby mode.
Press to turn on the soundbar. The indicator lights green.
Press again to return the soundbar to standby mode.
3 (Input) button
Press repeatedly to cycle through the sound source options
(RCA>AUX IN>OPTICAL IN).
4 DSP (Digital Signal
Processor) button and
indicator
Press repeatedly to cycle through the DSP sound modes:
• Standard - Lets you enjoy normal sound.
• Theater - Best for enjoying movies. Bass frequencies
are enhanced.
• News - Select for clear voice reproduction.
The corresponding indicator lights to indicate the sound
mode selected.
5 BASS button and indicator
Press to activate the bass frequency enhancement. The
indicator lights green. Press again to turn o the bass
frequency enhancement.
6 VOL +/– buttons
7 Hanging brackets
8 SUBWOOFER OUT jack
9 DC IN jack
Press to increase or decrease the volume of the soundbar.
Use to hang the soundbar on a wall.
Connect a powered subwoofer to this jack.
Connect the AC adapter to this jack to power the soundbar.
# Item
10 RCA IN (R and L) jacks
11 AUX IN jack
12 OPTICAL IN jack
13 (Power) button
14 INPUT button
15 DSP buttons
16 BASS button
17 VOL +/– buttons
18 (Mute) button
Description
If your TV (or other audio source device) has RCA OUT jacks,
connect the RCA cables to your source device and these jacks.
If your TV (or other audio source device) has an AUX OUT or
headphone jack, connect the 3.5 mm audio cable to your
source device and this jack.
If your TV (or other audio source device) has an Optical OUT
jack, connect a digital optical cable (not included) to your
source device and this jack.
Press to turn on the soundbar. Press again to return the
soundbar to standby mode.
Press repeatedly to cycle through the sound source options
(RCA>AUX IN>OPTICAL IN).
Press repeatedly to cycle through the DSP sound modes
(Standard>Theater >News ). The corresponding indicator on
the soundbar top panel lights to indicate the sound mode
selected.
Press to activate the bass frequency enhancement.
Press to increase or decrease the volume of the soundbar.
Press to mute the sound from the soundbar. Press again to
restore the sound.
- OR -
AUX IN connections (GOOD)
1 Connect the right-angled end of the 3.5mm audio cable to
your soundbar. Plug the other end into the Audio Output
port or headphone jack on your audio source device.
2 After connecting power, see USING YOUR SOUNDBAR on
the next page.
- OR -
RCA Audio connections (GOOD)
1 For an RCA audio connection, connect the right-angled
connectors to your soundbar. Connect the other end of the
RCA cables into the Audio Output ports on your audio
source device.
2 After connecting power, see USING YOUR SOUNDBAR on
the next page.
NOTE: Make sure the cable ends match the color of the ports.
TV, projector, or
DVD/Blu-ray player
OUTPUT
AUDIO
3.5 mm audio cable (included)
TV, projector, or
DVD/Blu-ray player
OUTPUT
AUDIO
Back of the soundbar
DC IN
18V
SUBWOOFER OUT
Back of the soundbar
LR
DC IN
18V
SUBWOOFER OUT
RCA audio cable (included)
DC IN
18V
SUBWOOFER OUT
L
R
RCA IN
AUX IN
OPTICAL IN
4
POSITION YOUR SOUNDBAR
You can mount your soundbar on the wall
(go to Step 5).
RCA IN
You can set the soundbar on a at surface
(go to Step 6).
AUX IN
OPTICAL IN
L
R
- OR -
L
R
RCA IN
AUX IN
OPTICAL IN
OVER
5
MOUNTING YOUR SOUNDBAR ON A WALL (OPTIONAL)
YOU WILL NEED:
Wall Mounting template
NOTE: Mounting instructions are also provided on the wall mounting template.
1 Select a location close to your TV and directly in front of the viewing/listening position. For best
sound quality, choose a location where sound waves are not blocked by furniture or other obstacles.
2 Position the wall mount template where you want to mount it and make sure it is level (A). Tape it to
the wall (B), then use a pencil to mark the screw hole locations (C). Remove the wall mount
template.
3 Install wall anchors (not included) into the marked locations using the instructions that came with
your anchors.
4 Secure two screws (not included) into the wall or wall anchors (if necessary). The screws must
protrude from the wall by about 1/2" (12.7 mm). Use a #10 wood screw (or similar) 1 1/2" in length.
5 Align the speaker hanging brackets with the screws, then hang the soundbar on the screws.
Pencil
Wall
16 in. (406 mm)
Level
Screws (2)
Measuring tape
Stud nder
(optional for wood
stud installation)
B CA
NOTES:
• If you have drilled into a stud, wall anchors are not required.
• See the instructions that came with your wall anchors to determine the drill bit size.
CAUTION: Use wall anchors designed for your wall type.
½ in. (12.7 mm)
Drill and
drill bit
Hammer
Screwdriver
Tape
WARNING: Improper installation can result in
serious injury or damage to your soundbar. If
necessary, seek the assistance of a professional.
#10 wood screw (or similar)
1 1/2" length
Wall anchors (2)
Listening to your soundbar
1 Press the (Power) button to turn on your soundbar or remote control. The power indicator
turns green.
2 Turn on the audio source device connected to your soundbar and begin playback.
3 Press the button on the soundbar or remote control repeatedly to cycle through the sound
sources until you hear sound from your soundbar.
NOTE: If you use the OPTICAL IN connection, change the source device’s audio source to ‘PCM’ format. Refer to
the documentation you received with the audio source device, such as your TV, for additional information.
4 Adjust the volume on your soundbar or the audio source device to a comfortable level.
WARNING: Continuous use of high volume sound may permanently damage your hearing.
5 Press the (Power) button again to turn o your soundbar. The standby indicator lights red.
Problem
The power does not
come on.
The remote control
does not work.
No sound or very
low-level sound is
heard from the
soundbar.
Your soundbar is not
working properly.
The sound is breaking
up or buzzing.
I can hear sound from
my TV and my soundbar.
My TV remote does not
control the volume of
my soundbar.
TROUBLESHOOTING
Check this list for a possible troubleshooting solution before calling for service (800-305-2204).
Also, check the online FAQs at dynexproducts.com.
Possible Solutions
• Make sure that the AC adapter is securely plugged into the power outlet and the soundbar.
• Remove any obstacles in the path between the remote control and the soundbar IR sensor.
• Replace the battery.
• Point the remote control at the remote control sensor on the soundbar.
• Move closer to the soundbar. The remote control reach is approximately 23 ft.
• Make sure that the volume level of the soundbar or your source device is set to an adequate level.
• Make sure that the volume is not muted. Press the (mute) button on the remote control.
• Make sure the correct audio source is selected. Press the button repeatedly to switch to the correct audio source.
• Make sure that the sound mode is suitable for the audio source. Press the DSP button to select a proper sound mode.
• Make sure the power is on and all connections are secure.
• Make sure the audio cable is connected to the Audio Output (not the Audio Input) on your source device.
• If you are connected to an MP3 player, make sure the volume is turned up on the MP3 player.
Note: The sound modes are memorized for each input, unless you disconnect the AC adapter from the wall outlet.
• Unplug the AC adapter from the wall outlet and then try plugging it in again after 30 seconds.
• Make sure all connections are secure and cables are not broken or damaged.
• If you are using the OPTICAL IN connection, make sure the source device’s audio source is set to “PCM” format. Refer
to the documentation your received with the audio source device (e.g. TV, projector, DVD/Blu-ray player, etc.) for
additional information.
• Connect to a dierent source device (e.g. TV, projector, DVD/Blu-ray player) to see if the buzzing still occurs. If it does
not, this may be an issue with the original source device.
• Use a dierent connection method (e.g. try Optical instead of AUX) between the soundbar and the source device to
make sure the jacks on both devices are still working.
• Turn o or mute the internal speakers of your source device. Refer to the device manual for instructions.
• Controlling your soundbar with your TV remote is a feature of your TV. See the documentation that came with your TV.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specied by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14 Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15 To reduce the risk of re or electric shock, do not expose this device to rain, moisture, dripping, or splashing, and no objects lled with liquids,
such as vases, shall be placed on it.
16 An apparatus with a three-prong, grounding-type plug is a Class I apparatus, which needs to be grounded to prevent possible electric shock.
Make sure that you connect any Class I device to a grounding-type, three-prong outlet.
17 The wall plug is the disconnecting device. The plug must remain readily operable.
18 Batteries should not be exposed to excessive heat such as sunshine, re, or the like.
WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Placement
• The soundbar cabinet is made out of plastic and is therefore sensitive to extreme temperatures and humidity, do not put it in locations subject
to direct sunlight or in humid places, such as near an air conditioner, humidier, bathroom, or kitchen.
• Do not put water or other liquids close to the soundbar. If liquid is spilled over the soundbar, it may be damaged.
• The soundbar should be placed on a sturdy, at surface that is free from vibration, or mounted on a wall. Do not put the soundbar on an uneven
or unstable surface, where it may fall and cause damage.
Using close to a TV or computer
Some older TVs and computer monitors are magnetically sensitive devices and as such are likely to suer discoloration or picture distortion when
conventional speakers are placed nearby. If discoloration problems persist, try moving the soundbar away from your TV or monitor.
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s
authority to operate this equipment.
CANADIAN NOTICE
CAN ICES-3 (B)/NMB-3(B)
Standard Television Receiving Apparatus — Appareil de réception télévision ordinaire, Canada BETS-7 / NTMR-7.
ONEYEAR LIMITED WARRANTY
Visit www.dynexproducts.com for details.
6
USING YOUR SOUNDBAR
Using the remote control
1 Remove the plastic tab from the battery compartment before using the remote control for the rst time.
2 Point the remote control directly at the IR sensor on the front of the soundbar. You must be within
approximately 23 ft. (7 m) of the soundbar.
IR sensor
SPECIFICATIONS
Designs and specications are subject to change without notice.
Dimensions (approx.)
Weight
Power source
Frequency response
Subwoofer source
31.5 × 3.5 × 2.7 in. (800 × 89 × 70 mm)
4.4 lbs. (2 kg)
20 W per channel at 10% THD
150 Hz ~ 15 kHz
2 V
CONTACT DYNEX:
For customer service, call 800-305-2204 (U.S. and Canada) or 01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a trademark of Best Buy and its aliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 14-0550
Loading...