Dynex DX-HTVMT1703-C Quick Setup Guide

DX-HTVMT1703-C

Tilting Mount for TVs 47"-70"

PACKAGE CONTENTS

• Hardware kit (1)

• Quick Setup Guide

Hardware kit includes:

Lag bolt

A (4)

Lag bolt washer

B (4)

Concrete anchor

C (4)

Tools needed:

Phillips

screwdriver

Drill

Before using your new product, please read these instructions to prevent any damage.

M4 × 12 screw

M4 × 30 screw

M5 × 12 screw

Wall plate (1)

TV brackets (2)

Wall plate template (1)

M5 × 30 screw

D (4)

E (4)

F (4)

Level

1/4 in. (6 mm) wood drill bit (for wood stud wall) OR 3/8 in. (10 mm) masonry drill bit (for concrete wall)

G (4)

M6 × 12 screw

H (4)

M6 × 20 screw

I (4)

Stud ﬁnder

M6 × 35 screw

J (4)

M6 washer

K (4)

Spacer

L (8)

Socket wrench

DETERMINING WHAT TYPE OF BACK YOUR TV HAS

1 Carefully place your TV screen face-down on a cushioned,

clean surface to protect the screen.

2 If a stand is installed, remove it. See the documentation that

came with your TV for instructions.

3 Lay the TV brackets, oriented vertically, on the back of your TV. 4 Align the screw holes in the TV brackets with the mounting

screw holes on your TV.

5 Identify which type of back your TV has:

• Flat back: The TV brackets lay ﬂush against the back of your TV and do not block any jacks. You do not need spacers.

• Obstructed back: The TV brackets block one or more of the jacks on the back of your TV. You need spacers (L).

• Irregularly-shaped back: There is a gap between the TV brackets and some part of the back of your TV. You need spacers (L).

6 Remove the TV brackets.

SELECT SCREWS, WASHERS, AND SPACERS

1 Select the hardware for your TV (screws, washers, and spacers).

If your TV came with mounting hardware, the screws are usually in the holes on the back of the TV.

If you don’t know the length of the mounting screws you

need, hand-thread diﬀerent screws to ﬁnd the correct length.

Select one of the following types of screws:

For a TV with a ﬂat back:

M4 × 12 mm screws (D) M5 × 12 mm screws (F) M6 × 12 mm screws (H)

Use the M6 washers (K) with all screws. If the TV has an

irregular or obstructed TV back, also use the spacers (L).

Screw ﬁts correctly

Screw is too long

Screw is

too short

2 Remove the screws from the holes in the back of your TV. 3 For a ﬂat back TV, go to “STEP 3 - Option 1: Attaching the

mounting hardware to TVs with a ﬂat back.”

-OR-

For an irregular or obstructed back, go to “STEP 3 - Option 2:

Attaching the mounting hardware to TVs with irregular or obstructed backs.”

For a TV with an irregular/obstructed back:

M4 × 30 mm screws (E) M5 × 30 mm screws (G) M6 × 20 mm screws (I) M6 × 35 mm screws (J)

Caution: Make sure that the screws (and spacers, if used) are the correct length. If the screw or screw/spacer combination is too long, it may damage the TV. If the screw or screw/spacer combination is too short, the TV may fall from the mount and damage the TV or injure someone. If you encounter resistance when testing screws, stop immediately and try another combination. If none of the screws or screw/spacer combinations work, contact customer service.

OPTION 1: ATTACHING THE MOUNTING HARDWARE TO TVS WITH A FLAT BACK

1 Align the TV brackets with the screw holes on the back of the

TV. Make sure that the brackets are level and that the tilt adjustment screws face out (away from the middle of the TV).

2 Place washers (K) over the holes in the TV brackets. Insert

screws (D, F, or H) through the washers and TV brackets.

3 Tighten the screws until they are snug against the TV brackets.

Do not over tighten.

Tilt adjustment

screw

OPTION 2: ATTACHING THE MOUNTING HARDWARE TO TVS WITH IRREGULAR OR OBSTRUCTED BACKS

1 Place spacers (L) over the holes on the back of the TV. You may

need to stack two spacers.

2 Align the left and right TV brackets with the screw holes on the

back of the TV. Make sure that the brackets are level and that the tilt adjustment screws face out (away from the middle of the TV).

3 Place washers (K) over the holes in the TV brackets. Insert screws

(E, G, I, or J) through the washers, TV brackets, and spacers.

4 Tighten the screws until they are snug against the TV brackets.

Do not over tighten.

Tilt adjustment

screw

DETERMINE THE WALLMOUNT LOCATION

The center of your TV will be oﬀset .8 in. lower than the center of the wall plate on the wall-mount. Before you drill holes in the wall:

• For more detailed information on determining where to drill your holes, visit our online height-ﬁnder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightﬁnder

• Your TV should be high enough so your eyes are level with the middle of the screen. This is normally 40 to 60 in. from the ground.

1 Measure the distance from the bottom of your TV to the

center point halfway between the top and bottom mounting holes on the back of your TV. This is measurement a.

2 Measure the distance from the ﬂoor to where you want the

bottom of the TV to be placed on the wall. Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment centers or TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray player or cable box). This measurement is b.

3 Add a + b. The total measurement is the height where you

want the center of the wall plate to be on the wall.

4 Use a pencil to mark this spot on the wall.

QUICK SETUP GUIDE

INSTALLING THE WALL PLATE

Wood installation 1 Locate the center of a stud with a stud ﬁnder.

2 Align the center of the wall plate template at the height

(a + b) you determined in the previous step, make sure that the template is level, then tape it to the wall.

3 Drill two pilot holes through the template to a depth of

2.75 in. (70 mm) using a 1/4 in. (6 mm) drill bit, then remove the template.

4 Align the plate with the pilot holes, insert the lag bolts

(A) through the lag bolt washers (B), then through the holes in the wall plate. Make sure that the wall plate is level.

5 Tighten the lag bolts with a socket wrench only until they

are ﬁrm against the wall plate.

Wood stud

Concrete installation

Caution: To prevent property damage or personal injury, never drill into

the mortar between blocks. Mount the wall plate directly onto the concrete surface.

1 Align the center of the wall plate template at the height (a + b)

you determined in the previous step, make sure that it is level, then tape it to the wall.

2 Drill two pilot holes through the template to a depth of 2.75 in.

(70 mm) using a 3/8 in. (10 mm) diameter masonry drill bit, then remove the template.

3 Insert the concrete wall anchors (C) into the pilot holes and

use a hammer to make sure that the anchors are ﬂush with the concrete surface.

4 Align the plate with the anchors, insert the lag bolts (A)

through the lag bolt washers (B), then through the holes in the wall plate. Make sure that the wall plate is level. Tighten the lag bolts with a socket wrench only until they are ﬁrm against the wall plate.

SECURING THE TV TO THE WALL PLATE

1 Holding the TV with the top of the screen tilted toward the

wall, slide the upper edges of the right and left TV brackets into the notches on the upper lip of the wall plate.

2 Gently pull down the straps on the wall plate so that the clips

lock into place.

Caution: Do not release the TV until the TV brackets are

securely locked onto the wall plate.

Clip

Strap

ADJUSTING THE TILT

1 Firmly hold the TV with one hand, then loosen the tilt

adjustment screw.

2 Tilt the TV to the angle you want, then tighten the tilt

adjustment screw.

Note: If you cannot loosen or fully tighten the tilt adjustment screw

by hand, use a Phillips screwdriver.

ONE-YEAR LIMITED WARRANTY

Visit www.dynexproducts.com for details.

CONTACT DYNEX:

For customer service, call 800-305-2204 www.dynexproducts.com

Made in China

Stud ﬁnder

* Minimum wood stud size: common 2 × 4 in. (51 × 102 mm) nominal

1 ½ × 3 ½ in. (38 × 89 mm).

* Minimum horizontal spacing between fasteners cannot be less than

16 in. (406 mm).

* Minimum solid concrete

thickness: 8 in. (203mm)

* Minimum concrete block

size: 8 × 8 × 16 in. (203× 203 × 406 mm).

* Minimum horizontal

spacing between fasteners cannot be less than 16 in. (406 mm).

HEAVY!

You will need assistance

with this step.

Concrete wall

V1 ENGLISH 16-0434