Dynex DX-HTVMM1703-C User Manual
Full Motion Mount for TVs 47" - 70"
DX-HTVMM1703-C
For VESA patterns:
• 7.9 × 7.9" (200 × 200 mm)
• 11.8 × 7.9" (300 × 200 mm)
• 11.8 × 11.8" (300 × 300 mm)
• 15.7 × 7.9" (400 × 200 mm)
• 15.7 × 11.8" (400 × 300 mm)
• 15.7 × 15.7" (400 × 400 mm)
• 19.7 × 15.7" (500 × 400 mm)
• 23.6 × 15.7" (600 × 400 mm)
For wood-stud or
concrete wall
installations
USER GUIDE
Before using your new product, please read these instructions to prevent any damage.
2
Maximum TV weight: 99 lbs. (45 kg)
Screen size: 47 in. to 70 in. diagonal
Overall dimensions (H × W ):
16.9 × 26.1 in. (42.9 × 66.3 cm)
Wall-mount weight: 14.3 lbs (6.5 kg)
We’re here for you
www.dynexproducts.com
For customer service, call:
1-800-305-2204
2
6
.
1
i
n
.
(
6
6
.
4
c
m
)
1
8
.
1
i
n
.
(
4
6
c
m
)
16.9 in. (43 cm)
1
8
i
n
.
(
4
5
.
7
c
m
)
Safety information and specifications
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specified by Dynex.
Improper installation may cause property damage or personal injury. If you do not
understand these directions, or have doubts about the safety of the installation,
contact Customer Service or call a qualified contractor. Dynex is not responsible for
damage or injury caused by incorrect installation or use.
The weight of your TV must not exceed 99 lbs. (45 kg). The wall must be capable of supporting five times
the weight of your TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
Full Motion Mount for TVs 47" - 70"DX-HTVMM1703-C
3
Edge-to-edge
stud finder
Phillips
screwdriver
Measuring
tape
Drill
3/16 in. (5 mm) wood drill bit
(for wood stud wall)
OR
3/8 in. (10 mm) masonry drill bit
(for concrete wall)
Hammer
Tap e
Pencil
Socket
wrench
5 × Allen wrench
Wall Mount (1)
Wall Plate Template (1)
TV Brackets (2)
Tools needed
You will need the following tools to assemble your new TV wall mount:
Full Motion Mount for TVs 47" - 70"DX-HTVMM1703-C
Package contents
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
4
Label Hardware Qty.
A1 4
A2 4
A3 4
A4 4
A5 4
A6 4
A7 4
A8 4
A9 4
A10 4
A11 4
M4 × 12 mm screw
M4 × 30 mm screw
M5 × 12 mm screw
M5 × 30 mm screw
M6 × 12 mm screw
M6 × 20 mm screw
M6 × 35 mm screw
M8 × 16 mm screw
M8 × 25 mm screw
M8 × 50 mm screw
Spacer
Label Hardware Qty.
A12 4
A13 4
B1 4
B2 4
B3 4
1
3
M4/M5 washer
M6/M8 washer
Lag bolt
Concrete anchor
Lag bolt washer
Magnetic removable
bubble level
Popper button
10 20 30 40 50 60 70 80 90 1 00mm
1234in
TV Hardware Bag
Full Motion Mount for TVs 47" - 70"DX-HTVMM1703-C
5
Full Motion Mount for TVs 47" - 70"DX-HTVMM1703-C
Installation instructions
STEP 1 - Determine whether your TV has a flat back or an irregular or obstructed back
1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches.
2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions.
3 Lay the TV brackets, oriented vertically, on the back of your TV.
4 Align the screw holes in the TV brackets with the mounting screw holes on your TV.
5 Identify which type of back your TV has:
• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers when assembling the wall mount.
• Obstructed back: The brackets block one or more of the jacks on the back of your TV. You will need spacers when assembling the wall mount.
• Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You will need spacers when assembling the wall
mount.
6 Remove the TV brackets.
Loading...