Dynex DX-GB5PRT User Manual
DX-GB5PRT_10-1123_QSG_V1.eps 1 10/29/2010 10:16:02 AMDX-GB5PRT_10-1123_QSG_V1.eps 1 10/29/2010 10:16:02 AM
V1
FINAL
FOR PRINT
DX-GB5PRT
5-Port Gigabit Ethernet Switch
Congratulations on your purchase of the DX-GB5PRT Dynex 5-Port
Gigabit Ethernet Switch. The DX-GB5PRT provides increased speed and
backbone connections to make Gigabyte a reality.
Safety Notices
• Do not use this product near water, for example, in a wet basement
or near a swimming pool.
• Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not place heavy objects on the switch.
• Allow room for adequate ventilation.
Package contents
• DX-GB5PRT Dynex 5-Port Gigabit Ethernet Switch
• Quick Setup Guide
Features
• Complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1p
standards
• Five 10/100/1000M RJ45 ports
• Supports IEEE 802.1p QoS
• Support Green Ethernet technology to implement power saving
features. (In Low Power Idle mode, up to 61.5% of the power can be
saved.)
• Supports IEEE 802.3x ow control for full-duplex mode and
backpressure for half-duplex mode
• Non-blocking switching architecture that forwards and lters
packets at full wire-speed for maximum throughput
• 8K entry MAC address table of the DX-GB5PRT with auto-learning
and auto-aging
• Supports for Jumbo frames of up to 15 KB
• LED indicators for monitoring power, link, and activity
Components
Front panel
Back panel
Power LED LEDs 1-5
Installing the switch
1 Connect the power adapter to the switch and power outlet.
Power cord
Power
outlet
Switch
2 Connect the PC(s) and other device(s) to the switch.
PC Switch
Network
storage
3 Connect the switch to the Internet.
Internet
Internet
Modem Router Switch
4 Install complete connection.
Internet
Modem
Router
Switch
Network
storage
PC
LED indicators
When the switch is plugged in and receiving power, the LED indicators
respond as follows:
LED
Power
Link/Act
Ports 1-5
Status
On (green)
O
On (orange)
Flashing (orange)
On (green)
Flashing (green)
Indication
Power on
No device is connected to the corresponding port.
A 10/100 Mbps device is connected to the corresponding port.
A 10/100 Mbps device is transmitting or receiving data
through the corresponding port.
A 1000Mbps device is connected to the corresponding port.
A 1000Mbps device is transmitting or receiving data through
the corresponding port.
Power portPorts 1-5
QUICK SETUP GUIDE
DX-GB5PRT_10-1123_QSG_V1.eps 2 10/29/2010 10:16:13 AMDX-GB5PRT_10-1123_QSG_V1.eps 2 10/29/2010 10:16:13 AM
Troubleshooting
1 The power LED is not lit
Make sure that the power adapter is connected correctly and the
power outlet is supplying power.
2 The link/act LED is not lit when a device is connected to the
corresponding port
Make sure that the cables are connected correctly and securely to
the switch and device. Make sure that the cable is not longer than
328 ft. (100 m).
Specications
Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,
IEEE 802.1p
Topology Star
Protocol CSMA/CD
Data transfer rate Ethernet: 10 Mbps (Half Duplex),
20 Mbps (Full Duplex)
Fast Ethernet: 100 Mbps (Half Duplex),
200 Mbps (Full Duplex)
Gigabit Ethernet: 2000 Mbps (Full Duplex)
Network media (cable) 10Base-T: UTP category 3, 4, 5 cable
(maximum 100 m)
EIA/TIA-568 100Ω STP (maximum 100 m)
100Base-TX: UTP category 5, 5e cable
(maximum 100 m)
EIA/TIA-568 100Ω STP (maximum 100 m)
1000Base-TX: UTP category 5e, 6 cable
(maximum 100 m)
EIA/TIA-568 100Ω STP (maximum 100 m)
Number of ports Five 10/100/1000M RJ45 ports
LED indicators Power, Link/Act
Transfer method Store-and-Forward
MAC address learning Automatic learning and aging
Frame lter rate 10Base-T: 14880 pps/Port
100Base-Tx: 148800 pps/Port
1000Base-T: 1488000 pps/Port
Frame forward rate 10Base-T: 14880 pps/Port
100Base-Tx: 148800 pps/Port
1000Base-T: 1488000 pps/Port
Operating temperature 32°F~104°F (0°C~40°C)
Storage temperature -40°F~158°F (-40°C~70°C)
Operating humidity 10%~90% non-condensing
Storage humidity 5%~90% non-condensing
Legal notices
FCC statement
This equipment complies with Part 15 of the FCC Rules. Operation is
subject to the following conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one of
more or the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
One-Year Limited Warranty
Visit www.dynexproducts.com for details.
Contact Dynex
For customer service please call 800-305-2204
www.dynexproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richeld, MN USA 55423-3645
© 2010 BBY Solutions, Inc. All Rights Reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All
other products and brand names are trademarks of their respective owners.
ENGLISH 10-1123
Loading...