Page 1
ASSEMBLY GUIDE
DX-DRTVM112
Low-Profile TV Wall Mount
Safety information and specifications . .2
Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . .3
For either wood-stud or
concrete wall installations
Before using your new product, please read these instructions to prevent any damage.
Package contents . . . . . . . . . . . . . . . . . . . . .4
Installation instructions. . . . . . . . . . . . . . . .5
Page 2
2
Maximum TV weight: 35 lbs.
(15.8 kg)
Screen size: 13 in. to 36 in. diagonal
Overall dimensions (H × W × D):
9.5 x 2.5 x 9.25 in.
(24.1 × 6.35 × 23.5 cm)
Wall-mount weight: 2.115 lb.
(0.959 kg)
We’re here for you
www.dynexproducts.com
For customer service, call:
1-800-305-2204 (U.S. and Canada) or
200 mm
100 mm
75 mm
200 mm
100 mm
75 mm
-6°
Compatible VESA patterns
Tilt range
Safety information and specifications
IMPORTANT
SAFETY
INSTRUCTIONS SAVE THESE
INSTRUCTIONS
CAUTION: Do
product for any purpose not explicitly
specified by Dynex.
Improper installation may cause property
damage or personal injury. If you do not
understand these directions, or have
doubts about the safety of the
installation, contact Customer Service or
call a qualified contractor. Dynex is not
responsible for damage or injury caused
by incorrect installation or use.
The weight of your TV must not exceed 35
lbs. (15.8 kg). The wall must be capable of supporting five times the weight of your TV and wall mount
combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
not use this
Page 3
DX-DRTVM112
Edge-to-edge stud
finder
Pencil
Level
Phillips screwdriver
Socket wrench with 7/16"
(12 mm) socket or
adjustable wrench
Measuring tape
Drill
1/8" (3 mm) wood drill
bit for wood stud wall
OR
3/8" (10 mm) masonry
drill bit (concrete only)
Hammer
Tap e
Adjustable wrench
Tools needed
3
ardware
You will need the following tools to assemble your new TV wall mount:
Page 4
4
A
B
D
C
Label Hardware Qty.
E4
F4
G4
H4
M4 × 12 mm
screw
M4 × 35 mm
screw
M4 washer
M4 spacers
Label Hardware Qty.
I2
J2
K4
L4
1/4" × 2 3/4" lag bolt
Concrete anchor
M6 x 14 mm screw
M6 Nut
Package contents
Make sure that you have all of the hardware necessary to assemble your new TV wall mount:
A TV Bracket (1)
B Wall Plate (1)
C Bracket Extensions (2)
D Wall mount template (1)
TV Hardware Bag
DX-TVM111
Template • Gabarit • Plantilla
Parte superior
Tools Needed
Outils nécessaires
Herramientas requeridas
Note
Remarque : Pour une construction à ossature de bois,
localiser d'abord les montants en bois, à l'aide d'un
détecteur de montants.
Nota: para la instalación en construcciones de armazón de
madera, primero debe localizar las vigas de madera con un
localizador de vigas.
Need more information about your mount? Scan
this QR code or visit www.dynexproducts.com.
<FR>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
<SP>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
http://san.us/284
Top
Haut
V1 13-0138
1234in
10 20 30 40 50 60 70 80 90 100mm
Page 5
DX-DRTVM112
100 mm
100 mm
75 mm
75 mm
200 mm
200 mm
100 mm
100 mm
75 mm
75 mm
200 mm
200 mm
L
K
C
A
L (4)
K (4)
Phillips screwdriver
Screws
Nuts
TV bracket (A)
Adjustable wrench
C (2)
Installation instructions
STEP 1 - Determining the hole pattern on your TV
1 Carefully place your TV screen face down on a cushioned, clean surface to protect the screen from
damage and scratches.
2 If your TV has a table top stand attached, remove the stand. See the documentation that came with your
TV for instructions.
3 Measure the distance between the mounting holes on the back of your TV.
4 If your TV has a 200 x 200 mm hole pattern, you must install the bracket extensions (C) onto the TV
bracket (A).
5
You’ll need
5 If you need to install the extension brackets (C), install them on the front (flat side) of the TV bracket (A)
with four M6 x 14 mm screws (K) and four M6 nuts (L), as shown, using the phillips screwdriver and the
adjustable wrench.
Page 6
6
STEP 2 - Determine whether your TV has a flat, irregular, or
obstructed back
1 Temporarily lay the TV bracket (A) and adapters (C), if necessary, on the back of your TV.
2 Align the screw holes in the TV bracket with the mounting screw holes on your TV.
3 Identify which type of back your TV may have:
• Flat back: The bracket and adapters (if necessary) lay flush against the back of your TV and does not
block any jacks. You do not need spacers when assembling the wall mount.
• Obstructed back: The bracket and adapters (if necessary) block one or more of the jacks on the back of
your TV. You will need spacers when assembling the wall mount.
• Irregularly-shaped back: There is a gap between the bracket and adapters (if necessary) and some
part of the back of your TV. You will need spacers when assembling the wall mount.
4 Remove the TV bracket (A) and adapters (C).
Page 7
DX-DRTVM112
Screw is too
long
Screw fits
correctly
Screw is too
short
STEP 3 - Select screws and spacers
1 Select the hardware for your TV (screws and spacers). A limited number of TVs come with mounting
hardware included. (If there are screws that came with the TV, they are almost always in the holes on the
back of the TV.)
Select one of the following types of screws:
M4 × 12 mm screws (E) for a flat back TV.
M4 × 35 mm screws (F) for an irregular or obstructed TV back.
For an irregular or obstructed TV back, use the following spacers:
M4 spacers (H)
7
CAUTION: To avoid potential personal
injuries and property damage, make sure that there
are adequate threads to secure the brackets to your
TV. If you encounter resistance, stop immediately and
contact customer service. Use the shortest screw and
spacer combination to accommodate your TV. Using
hardware that is too long may damage your TV.
However, using a screw that is too short may cause
your TV to fall from the mount.
2 Remove the screws.
3 For a flat back TV, go to “STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on
page 8.
-ORFor an irregular or obstructed back, go to “STEP 4 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs” on page 9.
Page 8
8
G
E
G (4)
E (4)
Phillips screwdriver
Screws
Wash ers
TV bracket (A)
STEP 4 - Option 1: Attaching the mounting hardware to TVs
with a flat back
1 Align the TV bracket (A) with the screw holes on the back of the TV.
2 Install washers (G ), and screws (E) into the holes in the back of the TV.
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
You’ll need
Page 9
DX-DRTVM112
G (4)
F (4)
Phillips screwdriver
Screws
Wash ers
Spacers
H (4)
TV bracket (A)
STEP 4 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs
1 Align the TV bracket (A) with the screw holes on the back of the TV.
2 Place spacers (H) behind the TV bracket and the washers (G) over the holes in the TV bracket, then insert
the screws (F) through the washers, TV bracket, and spacers.
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
A
H
G
F
9
You’ll need
Page 10
10
A
B
a
b
Measuring tape
Pencil
STEP 5 - Determine wall-mount location
Notes:
• For more detailed information on determining where to drill your holes, visit our online height-finder at:
http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder
• Your TV should be high enough so your eyes are level with the middle of the screen. Normally, the center
of your TV should be 40 to 60 inches (100 to 150 cm) above the floor.
The center of your TV will match the center of the wall plate (B). Before you drill holes in the wall:
1 Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is
measurement a.
2 Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall.
Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment
centers or TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray
player or cable box). This measurement is b.
3 Add a + b. The total measurement is the height where you want the center of the wall plate (B) to be on
the wall.
4 Use a pencil to mark this spot on the wall.
You’ll need
Page 11
DX-DRTVM112
D
I
B
3 in.
(75 mm)
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal
11/2 x 31/2 in. (38 x 89 mm).
Edge-to edge
stud finder
I (2)
Pencil
Drill
1/8" wood
drill bit
7/16" (12mm)
socket wrench
Level
Wall plate
(B)
Tem plat e (D)
Tap e
STEP 6 - Option 1: Installing on a wood stud* wall
Note: Any drywall covering the wall must not exceed 5/8" (16 mm).
1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.
2 Align the wall plate template (D) at the height you determined in the previous step and make sure that it
is level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).
3 Drill pilot holes to a depth of 3 in. (75 mm) using a 1/8" (3 mm) wood drill bit. Remove the wall plate
template.
4 Align the wall plate (B) with the pilot holes, insert the lag bolts (I) through the holes in the wall plate,
then tighten the lag bolts only until they are firm against the arm assembly.
CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (I).
11
You’ll need
DX-TVM111
Template • Gabarit • Plantilla
Top
Haut
Parte superior
Tools Needed
Outils nécessaires
Herramientas requeridas
Note
Remarque : Pour une construction à ossature de bois,
localiser d'abord les montants en bois, à l'aide d'un
détecteur de montants.
Nota: para la instalación en construcciones de armazón de
madera, primero debe localizar las vigas de madera con un
localizador de vigas.
Need more information about your mount? Scan
this QR code or visit www.dynexproducts.com.
<FR>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
<SP>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
http://san.us/284
V1 13-0138
Page 12
12
I
B
J
D
3 in.
(75 mm)
* Minimum solid concrete thickness: 8 in. (203 mm)
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
I (2)
Drill
3/8" masonry
drill bit
7/16" (12 mm)
socket wrench
Level
J (2)
Hammer
Wall plate (B)
Pencil
Tem plat e (D)
Tap e
STEP 6 - Option 2: Installing on a solid concrete* or concrete
block wall
CAUTION: To prevent property damage or personal injury, never drill into mortar between
blocks. Mount the wall plate directly onto the concrete surface.
1 Align the wall plate template (D) at t he height you determined in the pre vious ste p and make sure that it
is level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).
2 Drill pilot holes to a depth of 3 in. (75 mm) using a 3/8 in. (10 mm) diameter masonry drill bit. Remove
the wall plate template.
3 Insert the concrete wall anchors (J) into the pilot holes and use a hammer to make sure the anchors are
flush with the concrete surface.
4 Align the wall plate (B) with the anchors, insert the lag bolts (I) through the holes in the wall plate, then
tighten the lag bolts only until they are firm against the wall plate.
CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (I).
You’ll need
DX-TVM111
Template • Gabarit • Plantilla
Top
Haut
Parte superior
Tools Needed
Herramientas requeridas
Note
Remarque : Pour une construction à ossature de bois,
localiser d'abord les montants en bois, à l'aide d'un
détecteur de montants.
Nota: para la instalación en construcciones de armazón de
madera, primero debe localizar las vigas de madera con un
localizador de vigas.
Need more information about your mount? Scan
this QR code or visit www.dynexproducts.com.
<FR>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
<SP>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
http://san.us/284
Outils nécessaires
V1 13-0138
Page 13
DX-DRTVM112
B
A
B
A
HEAVY! You will need assistance
with this step.
For a vertical mount, attach the TV bracket to the flange that is closest to the wall plate.
For a tilt mount attach the TV bracket to the flange that is farthest from the wall plate.
B
A
B
A
STEP 7 - Mounting the TV to the wall plate
1 Place the TV bracket (A) into the slotted flanges of the wall plate (B). The TV can be mounted either (1)
vertically, or (2) with a 6° tilt.
2 Lock the TV and bracket assembly to the wall plate by rotating the lock into the flange slot.
13
Page 14
14
G
E
HEAVY! You will need assistance
with this step.
Phillips screwdriver
7/16" (12 mm)
socket wrench
STEP 8 - Removing the TV from the wall plate and
disassembling the wall mount
1 Unlock the TV and bracket assembly from the wall plate by rotating the lock out of the flange slot.
2 Lift the TV bracket (A) from the slotted flanges of the wall plate (B) and place it on a cushioned, clean
surface to protect the screen from damage and scratches.
3 Using a Phillips screwdriver, remove the screws from the back of your TV, then remove the TV bracket.
4 Using a 7/16” or 12 mm socket wrench, remove the lag bolts from the wall, then remove the wall plate.
A
B
B
A
You’ll need
Page 15
www.dynexproducts.com 1-800-305-2204 (U.S. and Canada) or 01-800-926-3020 (Mexico)
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
© 2013 BBY Solutions, Inc. All rights reserved.
brand names are trademarks of their respective owners.
6907-00205100
V1 ENGLISH 13-0668
Loading...