Serial Number ________________________________ Purchase Date _________________________________
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m. CST,
Monday – Friday or log on to customerservice@ghpgroupinc.com.
70-10-583 Rev. 9/21/16
1
TABLE OF CONTENTS
Safety Information ...................................................................................................................... 2
Replacement Parts List .............................................................................................................. 24
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or
install the product. If you have any questions regarding the product, call our customer service
department at 1-877-447-4768, 8:30 a.m.- 4:30 p.m. CST, Monday - Friday or log on to
customerservice@ghpgroupinc.com.
Use caution when lifting and moving the unit to avoid back strain or back injury. Do not move
the unit while it is in use.
• DO NOT operate the unit near or under ammable or combustible materials such as decks,
porches or carports.
• A minimum clearance to combustible construction is 36 in. (91.4 cm) from sides and back.
• DO NOT operate the unit under overhead construction.
• DO NOT use this smoker and grill as a heater.
• Operate the unit on a stable, level, noncombustible surface such as asphalt, concrete or
solid ground.
• DO NOT operate the unit on ammable material such as carpet or wood deck.
• Use caution when assembling and operating this unit to avoid cuts and scrapes from edges.
2
SAFETY INFORMATION
• DO NOT use this product in a manner other than its intended purpose. It is NOT intended for
commercial use. It is NOT intended to be installed or used in or on a recreational vehicle
and/or boats.
• DO NOT store this unit near gasoline or other combustible liquids or where other combustible
vapors may be present.
• DO NOT use or store or operate this unit in an area accessible to children or pets. Store this
unit in a dry protected location.
• DO NOT leave the unit unattended while in use.
• DO NOT leave hot ashes unattended, until the unit cools completely.
• DO NOT move the unit while in use, or while ashes are still hot. Allow the unit to cool completely
before moving or storing.
• NEVER use gasoline, kerosene, Zippo/Ronson lighter uid, or other highly volatile uids as a starter.
• Always cook your food on the grate after the ame is burned out.
• Dispose of cold ashes by wrapping them in heavy-duty aluminum foil and placing in a
noncombustible container. Make sure that there are no other combustible materials in or near
the container.
• If you must dispose of ashes in less time than it takes for the ashes to completely cool down,
remove the ashes from the unit using heat-resistant gloves along with long metal tongs or
replace shovel. Place the coals in aluminum foil and soak them completely with water before
disposing of them in a noncombustible container.
• Allow the unit to cool completely before conducting any routine cleaning or maintenance.
• This product will be hot during and after use. Use insulated oven mitts, or gloves, for protection
from hot surfaces or splatter from cooking liquids.
• Use caution when opening the primary door and offset lid of the unit while in operation. Keep
hands, face and body safe from hot steam or are-ups. DO NOT inhale smoke.
• DO NOT wear loose clothing while operating the unit. Tie back long hair while operating the unit.
• ALWAYS wear shoes that fully cover your feet while operating the unit.
• NEVER use glassware, plastic or ceramic cookware on or in the unit. Use metallic cookware only.
• Use of accessories not intended for this unit is not recommended and may lead to injury or
property damage.
• Read and follow all warnings and instructions before assembling and using the smoker and grill.
CALIFORNIA PROPOSITION 65
Fuels used in wood and charcoal burning appliances and the products of combustion of such
fuels contain chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm. This product contains chemicals, including lead and lead compounds, known to
the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after
handling.
3
PACKAGE CONTENTS
A1
Z
Y
W
V
U
B1
C1
X
P
H
A
A
B
C
D
E
F
G
I
A
T
S
R
Q
PART DESCRIPTION QUANTITY
A Smoker body 1
B Temperature gauge with nut 1
C Sausage hooks 1
D Side access door 1
E Cooking grate - smoker
body 5
F Side handle - smoker body 1
G Water bowl support 1
H Wheel - left / right 2
I Left leg assembly 1
J Water bowl 1
K Grease cup support 1
L Grease cup 1
M Right leg - front / rear 2
N Wheel axle 1
O
J
N
M
PART DESCRIPTION QUANTITY
O Offset damper plate 1
I
P Offset coupling bracket 2
Q Charcoal grate 1
R Cooking grate - offset 2
S Side handle - access tray 1
T Access tray 1
U Offset bottom section 1
V Offset lid handle 1
W Offset top section 1
X Offset lid 1
Y Offset lid bracket 1
Z Smoke stack 1
A1 Smoke stack damper 1
B1 Door handle assembly 1
C1 Offset rebox coupling 1
L
K
4
HARDWARE CONTENTS
AA
M6 x 30
Bolt
Qty. 4
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents above. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement parts.
BB
M6 x 12
Bolt
Qty. 33
CC
M6 x 45
Bolt
Qty. 3
DD
M6 Nut
Qty. 9
EE
M12 Nut
Qty. 2
FF
M6 Lock Nut
Qty. 1
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Phillips Screwdriver, Adjustable Wrench
5
ASSEMBLY INSTRUCTIONS
CAUTION: This unit is HEAVY! Do not attempt to
stand the unit upright without assistance!
1. Remove the preinstalled bolt and washer from
the bottom door hinge on the smoker body (A).
Unlatch the smoker door and remove the door by
pulling up from hinges on smoker body (A).
1
A
Preinstalled
bolt and
washer
2. Attach the side handle (F) using four M6 x 30 bolts
(AA) and four M6 nuts (DD).
Hardware Used
AA
M6 x 30mm
x 4
Bolt
DD
M6 Nut
x 4
2
DD
AA
F
6
ASSEMBLY INSTRUCTIONS
3. CAUTION: This unit is HEAVY! Do not
attempt to lay the unit on its side without
assistance!
Attach the right front and right rear legs (M) using
three M6 x 12 bolts (BB) per leg. Attach the left leg
assembly (I) using three M6 x 45 bolts (CC).
Hardware Used
BB
M6 x 12mm
x 6
Bolt
CC
M6 x 45mm
x 3
Bolt
3
CC
M
I
BB
4. Insert the wheel axle (N) through the holes on the
left leg assembly (I) and attach the left and right
wheel (H) using one M12 nut (EE) per side.
Hardware Used
EE
M12 Nut
x 2
4
N
EE
I
H
7
ASSEMBLY INSTRUCTIONS
5. Insert the edge of the offset lid bracket (Y) into
the slotted opening on the offset top section (W).
Attach using one M6 x 12 bolt (BB) and one
M6 nut (DD).
Hardware Used
BB
M6 x 12mm
x 1
Bolt
DD
M6 Nut
x 1
5
W
Y
BB
DD
6. Attach the offset bottom section (U) to the top
section (W) using six M6 x 12 bolts (BB).
Hardware Used
BB
M6 x 12mm
x 6
Bolt
6
BB
U
W
8
ASSEMBLY INSTRUCTIONS
7. Insert the offset rebox coupling (C1) through the opening on the top section of the offset (W) and
attach with four M6 x 12 bolts (BB).
Hardware Used
BB
M6 x 12mm
x 4
Bolt
7
W
C1
BB
8. Attach the offset coupling brackets (P) using four
M6 x 12 bolts (BB).
Hardware Used
BB
M6 x 12mm
x 4
Bolt
8
P
BB
9
ASSEMBLY INSTRUCTIONS
9. CAUTION: This unit is HEAVY! Do not attempt to stand the unit upright without
assistance!
Attach the offset rebox to the smoker body (A)
using four M6 x 12 bolts (BB).
Hardware Used
BB
M6 x 12mm
x 4
Bolt
9
A
BB
10. Attach the preinstalled offset support bracket
on the left leg assembly (I) to the bottom section
of the offset (U) using two M6 x 12 bolts (BB) and
two M6 nuts (DD).
Hardware Used
BB
M6 x 12mm
x 2
Bolt
DD
M6 Nut
x 2
10
I
U
DD
BB
10
ASSEMBLY INSTRUCTIONS
11. Rest the inner ring of the sausage hooks (C) on
the bottom brackets of the smoke stack (Z). Insert
the smoke stack (Z) up through the opening at the
top of the smoker body (A) and secure with three
M6 x 12 bolts (BB).
Hardware Used
BB
M6 x 12mm
x 3
Bolt
11
BB
A
Z
C
12. Attach the smoke stack damper (A1) using the
preinstalled spring and nut.
12
A1
11
ASSEMBLY INSTRUCTIONS
13. Hang the grease cup support (K) from the holes
on each of the right legs (M).
Place the grease cup (L) in the support (K).
13
M
L
K
14. Install the smoker body door and reattach the
preinstalled bolt and washer.
14
12
ASSEMBLY INSTRUCTIONS
15.Attach the door handle assembly (B1) using the
pre-installed at washer, spring washer
and M8 nut.
15
B1
16. Attach the temperature gauge (B) by inserting the
probe through the threaded opening on the smoker
body door and turning clockwise.
NOTE: The alignment of the temperature gauge
can be adjusted by turning the preinstalled nut
clockwise (or counter-clockwise) prior to installing.
16
B
13
ASSEMBLY INSTRUCTIONS
17. Attach the offset lid handle (V) to the offset lid (X)
using the preinstalled bolts and nuts.
17
X
V
18. Attach the offset lid (X) to the offset rebox using
the preinstalled bolt and washer.
18
X
Preinstalled bolt
and washer
14
ASSEMBLY INSTRUCTIONS
19. Install the side access door (D) onto the
smoker body (A).
19
A
D
20. Attach the side handle (S) to the access tray (T)
using two M6 x 12 bolts (BB) and two M6 nuts (DD).
Hardware Used
BB
M6 x 12mm
x 2
Bolt
DD
M6 Nut
x 2
20
T
DD
S
BB
15
ASSEMBLY INSTRUCTIONS
21. Attach the offset damper plate (O) to the access
tray (T) using one M6 x 12 bolt (BB) and one
M6 lock nut (FF).
Hardware Used
BB
M6 x 12mm
x 1
Bolt
FF
M6 Lock Nut
x 1
21
BB
FF
O
T
22. Place the charcoal grate (Q) inside the access
tray (T) and slide the tray into the offset smoker box.
22
Q
T
16
ASSEMBLY INSTRUCTIONS
23.Installing the Cooking Grates & Water Bowl
Install the offset cooking grates (R) into the offset
rebox. Place the water bowl support (G) on the
bottom bracket inside the smoker body (A) and
place the water bowl (J) on the water bowl
support (G). Place the cooking grates (E) on the
brackets inside the smoker body (A).
Tip: Place all 5 cooking grates (E) inside the
smoker body (A) and start from bottom
grate supports.
23
A
E
G
J
R
17
OPERATING INSTRUCTIONS
BEFORE FIRST USE
Remove all hangings or plastic straps, if present.
It is important to "season" the smoker & grill, before cooking food. Seasoning seals the paint and
interior to enhance avoring, durability and overall performance.
To season your smoker and grill, simply use it as you normally would without adding food.. You will
need to follow all of the lighting and operating procedures in the next few sections of this manual.
Using your desired avoring woods and marinades, burn your smoker at low temperature
(around 175°F/79.4°C) for 45 – 60 minutes. Let the smoker cool and clean out the wood chips and charcoal.
Once seasoning is complete, the smoker body and offset interior will have a durable, seasoned coating.
Lighting Instructions (For Smoking or Charcoal Grilling)
DO NOT USE PRETREATED, MATCH-LIGHT CHARCOAL with this smoker. Only use standard,
untreated briquettes or lump charcoal and ONLY use charcoal lighting uid approved for lighting charcoal.
Do not use lighter uid, paint thinners, gasoline, kerosene, alcohol or other ammable material for
lighting charcoal. Damage to the unit may occur with the use of match-light charcoal.
Start with at least 4 lbs. (1.8 kgs.) of charcoal (75 standard briquettes).
Make adjustments as needed when cooking in colder climates or during high winds, and/or when fair
amounts of precipitation are present.
Step 1
Note: Please refer to the manufacturer’s recommended amount of charcoal lighter uid before
applying uid to the briquettes. Charcoal can be added to the offset rebox by removing the offset
cooking grates or pulling out the side access tray. Pile the charcoal towards the middle of the offset
charcoal grate. Briquettes should be packed closely together for maximum burn efciency. Saturate
charcoal with the amount of charcoal lighter uid as recommended by the charcoal lighter uid
manufacturer. After soaking the charcoal, place the charcoal lighter uid at a safe distance away from
the smoker. Allow the charcoal lighter uid to soak into the charcoal for 3 minutes before lighting.
Step 2
With primary rebox door and offset lid open,, stand back and carefully light charcoal and allow to
burn until covered with a light ash (approximately 20 minutes). Charcoal lighter uid must be allowed
to completely burn off prior to closing the primary rebox door and offset lid. (Fumes will tend to
collect in both reboxes, when the primary door and offset lid are closed).
18
OPERATING INSTRUCTIONS
Lighting Instructions (Continued)
Step 3
After 20-25 minutes, charcoal should be ready for cooking and/or adding woodchips. Refer to the
next section before adding wood chips to pre-lit charcoal.
DANGER: Closing the smoker body door and offset lid during the lighting procedure could
trap fumes from the charcoal lighting uid in the smoker boxes and may result in a ash re or explosion when door is opened, resulting in property loss, personal injury or death.
Never attempt to add more lighting uid to the charcoal once it has been lit.
ADDING WOOD CHIPS (BEFORE AND DURING COOKING)
WARNING: Use caution since ames can are-up when fresh air suddenly comes in contact
with re. When opening the door, keep hands, face and body a safe distance from hot steam
and ame are-ups.
Presoaked Wood Chips
Soak the desired amount of chips in water for 30 minutes. Wrap the wood chips in aluminum foil
and poke holes on the top of the foil wrapping. FOLLOW THE STEPS BELOW BEFORE ADDING
PRESOAKED WOOD CHIPS.
Dry Wood Chips
Dry wood chips can be placed directly onto the pre-lit charcoal with or without aluminum foil.
FOLLOW THE STEPS BELOW BEFORE ADDING DRY WOOD CHIPS.
The amount and type of wood used is entirely dependent on the desired amount of avor. Refer to
the chart on the next page for tips on paring wood chips with various food types.
Step 1
Stand back and carefully open the offset lid allowing heat and steam to escape away from your face.
Use caution since ames can are-up when fresh air suddenly comes in contact with re. Wood can
be added by either removing the cooking grates with ame retardant oven mitts/gloves OR using the
side pull out tray.
Step 2
Wearing ame retardant oven mitts/gloves, use long metal cooking tongs to lightly brush aside ashes
on hot coals. Use the long metal cooking tongs to add wood chips (and/or charcoal) to directly onto
the charcoal, being careful not to stir-up ashes and sparks.
WARNING: Never add charcoal lighting uid to hot or even warm coals as ashback may
occur causing severe burns.
Step 3
Allow the ashes to completely cool before reusing or cleaning the smoker.
19
• Small wood chips work best inside the wood chip tray.
• Use dry hardwoods such as hickory, pecan, apple, cherry or mesquite.
• To produce more smoke and prevent fast burning, pre-soak the wood chips in a separate bowl
of water for at least 30 minutes, or wrap the chips in perforated aluminum foil.
• Most smoke avoring occurs within the rst hour of cooking. Adding wood chips after the rst
hour is typically not necessary unless extra smoke avoring is desired.
Here's a list of the most popular smoking woods and a little information about each.
Type of WoodSuggested FoodComments
Mild and sweet avor with a slight hint of fruity avor. Each
AppleAll meats
AlmondAll meatsProduces a sweet smoke with a natural nutty avor.
AshFish and red meatVery light avor.
CitrusPork and chickenLemon and orange wood produce light but fruity avor.
species of Apple wood should offer a slightly different avor.
Apple smoke produces an attractive browning effect.
CherryPork and beefLight and fruity avor.
FruitwoodPork, poultry and sh
GrapevinePoultry, game and lamb
HickoryPork and beef
MaplePork and poultryLight and sweet.
MesquiteBeef, chicken and sh
OakRed meats, game, ribs and sh
PecanRibs and red meatProduces a light smoke that offers a sweet and nutty avor.
Wood such as Peach, Pear and Plum produce a mild but sweet
smoke with a hint of fruity avor.
Grapevine wood produces a lot of smoke. A little wood goes a
long way. It produces a tart avor that has a hint of fruit.
Hickory is arguably the favorite wood for smoking. Hickory
produces a very strong avor so we recommend starting slow
with this wood.
This wood burns very hot so be aware. Much like Hickory,
Mesquite is very popular and produces a strong avor.
Another wood that produces a heavy smoke. Start slow with this
wood.
20
SUGGESTED SMOKING AND MEAT TEMPERATURES
Smoking Temperatures
Accurate smoking temperatures are critical for safely cooking food when meat probes are not
available. Please understand that using the factory installed temperature gauge is an acceptable
tool for smoking food; but it’s not always the ideal means of measuring the most accurate smoking
temperature because internal smoker temperatures can vary between the top and bottom cooking
grates. Also keep in mind that the probes used on most gauges are designed to measure the
temperature at the tip of the temperature probe and not the overall temperature of the smoker.
Alternatively, it is recommended that users either purchase an aftermarket, oven-ready temperature
gauge, or a meat thermometer. Meat thermometers are the most effective way of determining when
the food is cooked to the minimum temperature required for safe consumption.
Please refer to the chart below for cooking temps.
(wild turkey, duck, goose, partridge and pheasant)
Whole 250°F (121°C) 180°F (82°C)
Breasts and roasts 250°F (121°C) 165°F (74°C)
Thighs, wings 250°F (121°C) 165°F (74°C)
Stung(cookedalone250°F(121°C) 165°F (74°C)or in a bird)
Since it is dicult to use a food thermometer to check the temperature of
shellsh, discard any that do not open when cooked.
21
CARE AND MAINTENANCE
AFTER USE SAFETY AND MAINTENANCE
WARNING
• Use caution when lifting and moving the smoker to avoid strain injuries.
Two people are recommended to lift or move the smoker.
• DO NOT store the smoker near gasoline or other combustible liquids or where combustible vapors
may be present. Keep the area around the smoker clear and free of combustible materials
and vapors.
• DO NOT store this smoker in an area accessible to children or pets. Store the smoker in a dry,
protected location.
• DO NOT allow anyone to conduct activities around the smoker following use until it has cooled. It is
hot during operation and remains hot for a period of time following use.
• DO NOT leave hot ashes unattended until the smoker cools completely.
• The smoker becomes extremely hot – allow the smoker to cool completely before handling. Allow
the smoker to cool before removing and cleaning the grease pan.
• Dispose of cold ashes by wrapping them in heavy-duty aluminum foil and putting them in a
noncombustible container.
• If you must dispose of the ashes in less time than it takes for them to completely cool, remove the
side access tray using heat-resistant gloves and place the ashes in aluminum foil. Completely soak
the ashes with water before disposing of them in a noncombustible container.
CAUTION: All care and maintenance procedures are to be performed while the
smoker is completely cooled.
Clean the cooking grates with hot, soapy water. Rinse and dry thoroughly. You may prefer to coat the
cooking grates lightly with cooking oil or cooking spray.
To clean the inside and outside of the smoker cabinet, simply use a damp cloth.
Spray-washing with a water hose is not recommended. Moisture should be wiped away and not
allowed to stand inside or on top of the smoker. Once cleaned, you may prefer to lightly coat the
interior of the smoker cabinet with cooking oil or cooking spray.
If rust is present on the exterior surface of the smoker, clean the area with steel wool or
emery cloth and use heavy-duty, heat-resistant paint.
NEVER apply additional paint to the interior of the smoker. If rust is present on the interior of the
smoker, clean it thoroughly with steel wool or emery cloth and lightly coat the area with cooking oil or
cooking spray to help minimize recurring rust.
To protect your smoker from weather conditions, always keep it covered while not in use.
22
WARRANTY
This charcoal offset vertical smoker and grill is warranted against broken or damaged parts at the
time of purchase. All parts carry a one (1) year limited warranty. Paint is warranted to be free of
defects for 90 days except for rust, which may appear after repeated use.
This warranty does not cover damage or issues related to neglect, abuse or modications to the
appliance. Repair labor is not covered.
All parts that meet the warranty requirements will be shipped at no charge via the discretion of GHP
Group Inc. (ground shipments, US Mail or Parcel Post ONLY). Any special handling charges (i.e.
Second Day, Overnight, etc.) will be the responsibility of the consumer.
All warranty claims apply only to the original purchaser and require a proof of purchase verifying
purchase date. Do not return parts to GHP address without rst obtaining a return authorization
number from our customer service. This service is available by calling toll free 1-877-447-4768,
8:30 a.m. - 4:30 p.m. CST, Monday - Friday.
Some states do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not
apply to you. This warranty gives you specic legal rights, and you may have other rights that vary
from state to state.
GHP Group Inc.
6440 W. Howard Street
Niles, IL, USA
60714-3302