DVR systems DVRxx04HF-S User Manual

Page 1
N6 Series Standalone DVR User’s Manual
Version 4.4.0
1
Page 2
1 FEATURES AND SPECIFICATIONS.................................................................. 1
1.1 Overview .................................................................................................................................................1
1.2 Features..................................................................................................................................................1
1.3 Specifications .........................................................................................................................................2
1.3.1 1U Series ...........................................................................................................................................2
1.3.2 1.5U Series ........................................................................................................................................ 6
1.3.3 Simple 1.5 U ...................................................................................................................................... 9
1.3.4 2U Series .........................................................................................................................................12
1.3.5 2U Series HD-SDI series....................................................................................................... 16
1.3.5 2U Series 960H series.......................................................................................................... 19
2 OVERVIEW AND CONTROLS ......................................................................... 23
2.1 Front Panel ...........................................................................................................................................23
2.1.1 1U series .......................................................................................................................................... 23
2.1.2 1.5U series.......................................................................................................................................24
2.1.3 2U series (HD-SDI series, 960H included) .................................................................................26
2.2 Rear Panel............................................................................................................................................29
2.2.1 1U series .......................................................................................................................................... 29
2.2.2 1.5U series.......................................................................................................................................29
2.2.3 Simple 1.5U .....................................................................................................................................30
2.2.4 2U series .......................................................................................................................................... 31
2.2.5 2U series (HD-SDI series) .............................................................................................................. 31
2.2.5 2U series (960H series) .................................................................................................................. 32
2.3 Connection Sample.............................................................................................................................33
2.3.1 1U series .......................................................................................................................................... 33
2.3.2 1.5U series.......................................................................................................................................34
2.3.3 2U series .......................................................................................................................................... 35
2.3.4 2U series (HD-SDI series) ............................................................................................................. 37
2.3.4 2U series (960H series) ................................................................................................................. 37
i
Page 3
2.4 Remote Control....................................................................................................................................38
2.5 Mouse Control......................................................................................................................................40
2.6 Virtual Keyboard & Front Panel.........................................................................................................42
2.6.1 Virtual Keyboard.............................................................................................................................. 42
2.6.2 Front Panel ......................................................................................................................................42
3 INSTALLATION AND CONNECTIONS............................................................. 43
3.1 Check Unpacked DVR........................................................................................................................43
3.2 About Front Panel and Real Panel ...................................................................................................43
3.3 HDD Installation...................................................................................................................................43
3.3.1 1U series .......................................................................................................................................... 43
3.3.2 1.5U series.......................................................................................................................................44
3.3.3 2U series HD-SDI series, 960H ...........................................................................................44
3.4 Rack Installation ..................................................................................................................................45
3.5 Connecting Power Supply..................................................................................................................45
3.6 Connecting Video Input and Output Devices ..................................................................................45
3.6.1 Connecting Video Input.................................................................................................................. 46
3.6.2 Connecting Video Output...............................................................................................................46
3.7 Connecting Audio Input & Output, Bidirectional Audio ..................................................................46
3.7.1 Audio Input.......................................................................................................................................46
3.7.2 Audio Output.................................................................................................................................... 46
3.8 Alarm Input and Output Connection .................................................................................................47
3.8.1 Alarm Input and Output Details..................................................................................................... 47
3.8.2 Alarm Input Port .............................................................................................................................. 51
3.8.3 Alarm Output Port ........................................................................................................................... 52
ii
Page 4
3.9 RS232....................................................................................................................................................52
3.10 RS485....................................................................................................................................................52
3.11 Other Interfaces ...................................................................................................................................53
4 OVERVIEW OF NAVIGATION AND CONTROLS ............................................ 55
4.1 Login, Logout & Main Menu ...............................................................................................................55
4.1.1 Login ................................................................................................................................................. 55
4.1.2 Main Menu .......................................................................................................................................56
4.1.3 Logout............................................................................................................................................... 56
4.1.4 Auto Resume after Power Failure ................................................................................................ 57
4.1.5 Replace Button Battery .................................................................................................................. 57
4.2 Manual Record.....................................................................................................................................57
4.2.1 Live Viewing..................................................................................................................................... 57
4.2.2 Manual record..................................................................................................................................57
4.3 Search & Playback ..............................................................................................................................59
4.4 Schedule ...............................................................................................................................................62
4.4.1 Schedule Menu .................................................................................................................................... 62
4.4.2 Snapshot .......................................................................................................................................... 64
4.4.3 Image FTP .......................................................................................................................................66
4.4.4 Snapshot Disk (For special series only) ...................................................................................... 66
4.5 Detect ....................................................................................................................................................67
4.5.1 Go to Detect Menu............................................................................................................................... 67
4.5.2 Motion Detect........................................................................................................................................ 67
4.5.3 Video Loss.............................................................................................................................................69
4.5.4 Camera Masking..................................................................................................................................70
4.6 Alarm Setup and Alarm Activation ....................................................................................................71
4.6.1 Go to alarm setup interface ........................................................................................................... 71
4.6.2 Alarm setup...................................................................................................................................... 71
iii
Page 5
4.7 Backup ..................................................................................................................................................73
4.7.1 Detect Device....................................................................................................................................... 73
4.7.1 Backup.............................................................................................................................................. 73
4.8 PTZ Control and Color Setup ............................................................................................................74
4.8.1 Cable Connection ................................................................................................................................74
4.8.2 PTZ Setup.............................................................................................................................................74
4.8.3 3D Intelligent Positioning Key............................................................................................................ 76
4.9 Preset/ Patrol/Pattern/Scan................................................................................................................76
4.9.1Preset Setup .........................................................................................................................................77
4.9.2 Activate Preset..................................................................................................................................... 78
4.9.3 Patrol setup (Tour Setup)................................................................................................................... 78
4.9.4 Activate Patrol (tour) ........................................................................................................................... 78
4.9.5 Pattern Setup....................................................................................................................................... 78
4.9.6 Activate Pattern Function...................................................................................................................78
4.9.7 Auto Scan Setup .................................................................................................................................79
4.9.8 Activate Auto Scan.............................................................................................................................. 79
4.10 Flip .........................................................................................................................................................79
5 UNDERSTANDING OF MENU OPERATIONS AND CONTROLS ................... 80
5.1 Menu Tree ............................................................................................................................................80
5.2 Main Menu ............................................................................................................................................80
5.3 Setting ...................................................................................................................................................81
5.3.1 General............................................................................................................................................. 81
5.3.2 Encode .............................................................................................................................................83
5.3.3 Schedule .......................................................................................................................................... 84
5.3.4 RS232............................................................................................................................................... 84
5.3.5 Network ............................................................................................................................................ 85
5.3.6 Alarm.................................................................................................................................................94
5.3.7 Detect ...............................................................................................................................................94
5.3.8 Pan/Tilt/Zoom .................................................................................................................................. 94
5.3.9 Display..............................................................................................................................................95
5.3.10 Default.......................................................................................................................................... 96
iv
Page 6
5.4 Search ...................................................................................................................................................97
5.5 Advanced ..............................................................................................................................................97
5.5.1 HDD Management..........................................................................................................................98
5.5.2 Abnormity ....................................................................................................................................... 101
5.5.3 Alarm Output..................................................................................................................................102
5.5.4 Manual Record..............................................................................................................................102
5.5.5 Account...........................................................................................................................................102
5.5.6 Auto Maintain................................................................................................................................. 105
5.5.7 TV Adjust........................................................................................................................................ 105
5.5.8 Video Matrix...................................................................................................................................106
5.5.9 Card Overlay..................................................................................................................................106
5.5.10 Config File Backup...................................................................................................................108
5.6 Information..........................................................................................................................................109
5.6.1 HDD Information ........................................................................................................................... 109
5.6.2 BPS................................................................................................................................................. 110
5.6.3 Log .................................................................................................................................................. 110
5.6.4 Version ...........................................................................................................................................111
5.6.5 Online Users.................................................................................................................................. 112
5.7 Shutdown............................................................................................................................................112
6 ABOUT AUXILIARY MENU ............................................................................ 114
6.1 Go to Pan/Tilt/Zoom Menu ...............................................................................................................114
6.1.1 3D Intelligent Positioning Key ..................................................................................................... 114
6.2 Preset /Patrol / Pattern /Border Function.....................................................................................115
6.2.1 Preset Setup.................................................................................................................................. 116
6.2.2 Activate Preset .............................................................................................................................. 116
6.2.3 Patrol Setup ................................................................................................................................... 116
6.2.4 Activate Patrol ............................................................................................................................... 116
6.2.5 Pattern Setup................................................................................................................................. 116
6.2.6 Activate Pattern Function............................................................................................................. 117
6.2.7 Border Setup.................................................................................................................................. 117
6.2.8 Activate Border Function .............................................................................................................117
6.2.9 Flip ..................................................................................................................................................117
v
Page 7
7 WEB CLIENT OPERATION ............................................................................ 119
7.1 Network Connection..........................................................................................................................119
7.2 Login....................................................................................................................................................119
7.2.1 Real-time Monitor.......................................................................................................................... 122
7.2.2 PTZ .................................................................................................................................................124
7.2.3 Color ...............................................................................................................................................126
7.2.4 Picture Path and Record Path ....................................................................................................126
7.3 Configure ............................................................................................................................................127
7.3.1 System Information....................................................................................................................... 128
7.3.2 System Configuration...................................................................................................................130
7.3.3 Advanced ....................................................................................................................................... 149
7.3.4 Additional Function ....................................................................................................................... 156
7.4 Search .................................................................................................................................................158
7.5 Alarm ...................................................................................................................................................161
7.6 About ...................................................................................................................................................162
7.7 Log out ................................................................................................................................................163
7.8 Un-install Web Control......................................................................................................................163
8 PROFESSIONAL SURVEILLANCE SYSTEM ................................................ 164
9 FAQ................................................................................................................. 165
APPENDIX A HDD CAPACITY CALCULATION ................................................. 170
APPENDIX B COMPATIBLE BACKUP DEVICE LIST........................................ 171
vi
Page 8
APPENDIX C COMPATIBLE CD/DVD DEVICE LIST............................................ 175
APPENDIX D COMPATIBLE DISPLAYER LIST ................................................. 176
APPENDIX E COMPATIBLE SWITCHER LIST .................................................. 177
APPENDIX F COMPATIBLE WIRELESS MOUSE LIST ..................................... 178
APPENDIX G EARTHING.................................................................................... 179
APPENDIX H TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS................ 184
vii
Page 9
Welcome
Thank you for purchasing our DVR!
This user’s manual is designed to be a reference tool for the installation and operation of your
system.
Here you can find information about this series DVR features and functions, as well as a detailed
menu tree.
Before installation and operation please read the following safeguards and warnings carefully!
viii
Page 10
Important Safeguards and Warnings
1Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3Installation
Keep upwards. Handle with care.
Do not apply power to the DVR before completing installation.
Do not place objects on the DVR
4Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5Environment
The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc. This series product shall be transported, storage and used in the environment ranging from 0 to 55
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
ix
Page 11
1 FEATURES AND SPECIFICATIONS
1.1 Overview
This series product is an excellent digital monitor product designed for security field. It adopts
embedded Linux OS to maintain reliable operation. Popular H.264 compression algorithm and
G.711 audio compression technology realize high quality, low bit stream. Unique frame by frame
play function is suitable for detail analysis. It has various functions such as record, playback,
monitor at the same time and can guarantee audio video synchronization. This series product
has advanced technology and strong network data transmission function.
This series device adopts embedded design to achieve high security and reliability. It can work in
the local end, and at the same time, when connecting it to the professional surveillance software
(PSS), it can connect to security network to realize strong network and remote monitor function.
This series product can be widely used in various areas such as banking, telecommunication,
electric power, interrogation, transportation, intelligent resident zone, factory, warehouse,
resources, and water conservancy.
1.2 Features
This series product has the following features:
z Real-time monitor
It has analog output port, VGA port and HDMI port. You can use monitor or displayer to realize
surveillance function.
System supports TV/VGA/HDMI output at the same time.
z Storage function
Special data format to guarantee data security and can avoid vicious data modification.
z Compression format
Support multiple-channel audio and video. An independent hardware decodes the audio and
video signal from each channel to maintain video and audio synchronization.
z Backup function
Support backup operation via USB port (such as flash disk, portable HDD, burner).
Client-end user can download the file to local HDD to backup via network.
z Record playback function
Support each channel real-time record independently, and at the same time it can support search,
forward play, network monitor, record search, download and etc.
Support various playback modes: slow play, fast play, backward play and frame by frame play.
Support time title overlay so that you can view event accurate occurred time
Support specified zone enlargement.
z Network operation
1
Page 12
Support network remote real-time monitor, remote record search and remote PTZ control.
z Alarm activation function
Several relay alarm outputs to realize alarm activation and on-site light control.
The alarm input port and output has the protection circuit to guarantee device safety.
z Communication port
RS485 port can realize alarm input and PTZ control.
RS232 port can connect to keyboard to realize central control, and can also connect to PC COM
to upgrade system and realize maintenance, and matrix control.
Standard Ethernet port can realize network access function.
Dual Ethernet ports support configuration modes such as multiple access, Fault-tolerance and
load balancing.
z PTZ control
Support PTZ decoder via RS485.
Support various decode protocols to allow the PTZ to control the speed dome.
z Intelligent operation
Mouse operation function
In the menu, support copy and paste setup function
z UPnP
It is to establish the mapping relationship between the LAN and the WAN via the UPnP protocol.
Slight function differences may be found due to different series.
1.3 Specifications
1.3.1 1U Series
System
Compression Standard
Parameter
Main Processor
OS System
Resources Interface Input
Devices Input Method Shortcut Function Video Compressio n
4-ch 8-ch 16-ch
High-performance industrial embedded micro controller
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback and network operation simultaneously User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese (optional) Copy/paste operation, USB mouse right-key shortcut menu, double click USB mouse to switch screen.
H.264
2
Page 13
Audio
G.711A
4-CH composite video input: (NTSC/PAL)
B
BNC (1.0V
P- P,
B75)
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output. 1-ch VGA output. 1-ch HDMI output. 1-ch matrix output. Support TV/VGA/HDMI video output at the same time.
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per channel
Video monitor
Compressio n
Video Input
Video Output
Video Standard
Record Speed
8-CH composite video input: (NTSC/PAL) BNC (1.0VB
P- P,
B75)
16-CH composite video input: (NTSC/PAL) BNC
B
P- P,
B75)
(1.0V
Audio
Video
1/4 windows(Optional) 1/4/8/9 windows 1/4/8/9 /16 windows Partition Monitor Touring
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL/NTSC
Real-time monitor
D1 704×576/704×480 Resolution
(PAL/NTSC )
Playback
1/16-ch: D1 704×576/704×480, HD1 704×288/704×240, BCIF
352×576/352×480, CIF 352×288/ 352×240 , QCIF 176×144/176×120
Support dual streams: extra stream resolution CIF 352×288/ 352×240,
QCIF 176×144/176×120. Image
6-level image quality (Adjustable) Quality Privacy mask Image Information
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
Channel information, time information and privacy mask zone.
TV Adjust Adjust TV output zone suitable to anamorphic video.
Channel Lock
Cover secret channel with black screen though system is encoding
normally.
Screen-lock function to prevent unauthorized user seeing secret video. Channel Information
Channel name, recording status, screen lock status, video loss status
and motion detection status are shown on the bottom left of display
screen. Color
Hue, brightness, contrast, saturation and gain setup for each channel. Configuratio n
Audio Input
Audio Output
4-ch 200-2000mv
10K(BNC)
1-ch audio output 200-
3000mv 5KΩ(BNC)
8-ch 200-2000mv 10K(BNC)
1-ch audio output 200­3000mv 5KΩ(BNC)
4-ch 200­2000mv 10K (BNC)
1-ch audio output 200-3000mv 5K(RCA)
3
Page 14
1-ch audio talk output
200-3000mv 5KΩ(BNC)
2 built-in SATA port. Support 2 HDDs.
AudioPCM 28.8MByte/h
Video56-900MByte/h
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback
and reverse play mode.
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when a file is end system auto plays the
next file in the current channel
There is 1/4/9/16-channel playback mode.
(It may vary due to different series.)
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone
to activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk and
etc.)
Support peripheral USB burner.
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and
video loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Duplex transparent COM
Network alarm input and output
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Support record activation function or activate external alarm or screen
message in specified period.
Hard disk
Record and playback
Backup function
Network Function
Motion Detection and Alarm
Bidirectional Audio
Hard Disk Hard Disk
Occupation
Recording Mode
Recording Length Playback Repeat Way Record Search Playback Mode Various File Switch Ways
Multi­channel Playback Window Zoom Partial Enlargemen t
Backup Mode
Network control
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm
1-ch audio talk output 200-3000mv 5KΩ(BNC)
1-ch audio talk output 200­3000mv 5KΩ (RCA)
4
Page 15
Manual Alarm Control
Alarm Input
Alarm Output
Alarm Relay
Interface
System Information
User Management
Upgrade
Login, Logout and Shutdown
General Parameter
USB Interface Network connection
RS485
RS232
Hard Disk Information Data Stream Statistics Log statistics
Version
On-line user Display current on-line user
User Manageme nt
Password Authenticati on
Power Power
Consumptio n
Working Temperatur e Working Humidity Air Pressure
Enable or disable alarm input channel
Support analog alarm signal to specific alarm output channel.
4-ch alarm input(You
can set normal open or
normal close type to
select the alarm type.
3-channel relay output.
30V DC 2A,125VAC 1A(activation alarm
2 USB 2.0 ports.
RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port
Support various PTZ control protocols.
Ordinary COM (Debug),keyboard connection and transparent serial
port(COM input and output via network )
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, alarm input and output
amount, system version and release date.
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
Right authentication when shut down to make sure only those proper
people can turn off DVR
DC 12V
25W (With adapter, exclude HDD)
0℃-+55
10%90%
86kpa106kpa
8-ch alarm input(You can set normal open or normal close type to select the alarm type.
16-ch alarm input You can set normal open or normal close type to select the alarm type.
5
Page 16
Dimension Weight 1.5-2.5KG(Exclude HDD)
Installation Mode
1U standard industrial case. 375(W) x280 (D) x50mm(H)
Desktop installation
1.3.2 1.5U Series
System
Parameter
Main Processor
4-ch 8-ch 16-ch
High-performance industrial embedded micro controller
Compression Standard
Video monitor
OS System
Resources Interface Input
Devices Input Method Shortcut Function Video Compressio n Audio Compressio n
Video Input
Video Output
Video Standard
Record Speed
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback
and network operation simultaneously
User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese
(optional)
Copy/paste operation, USB mouse right-key shortcut menu, double click
USB mouse to switch screen.
H.264
G.711A
4-CH composite video
input: (NTSC/PAL)
B
BNC (1.0V
P- P,
B75)
8-CH composite video input: (NTSC/PAL) BNC (1.0VB
P- P,
B75)
16-CH composite video input: (NTSC/PAL) BNC
B
P- P,
B75)
(1.0V
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output.
1-ch VGA output.
1-ch HDMI output.
1-ch matrix output.
Support TV/VGA/HDMI video output at the same time.
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s
per channel
Video Partition Monitor Touring
Resolution (PAL/NTSC )
Image Quality
1/4 windows(Optional) 1/4/8/9 windows 1/4/8/9 /16 windows
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL/NTSC
Real-time monitor
D1 704×576/704×480
Playback
1/16-ch: D1 704×576/704×480 , CIF 352×288/ 352×240 , QCIF
176×144/176×120
Support dual streams: extra stream resolution CIF 352×288/ 352×240,
QCIF 176×144/176×120.
6-level image quality (Adjustable)
6
Page 17
Privacy mask Image Information
TV Adjust Adjust TV output zone suitable to anamorphic video.
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
Channel information, time information and privacy mask zone.
Audio
Hard disk
Record and playback
Backup function
Channel Lock
Channel Information
Color Configuratio n
Audio Input
Audio Output
Bidirectional Audio
Hard Disk Hard Disk
Occupation
Recording Mode
Recording Length Playback Repeat Way Record Search Playback Mode Various File Switch Ways
Multi­channel Playback Window Zoom Partial Enlargemen t
Backup Mode
Network control
Cover secret channel with black screen though system is encoding
normally.
Screen-lock function to prevent unauthorized user seeing secret video.
Channel name, recording status, screen lock status, video loss status
and motion detection status are shown on the bottom left of display
screen.
Hue, brightness, contrast, saturation and gain setup for each channel.
4-ch 200-2000mv
10K(BNC)
1-ch audio output 200-3000mv 5KΩ(BNC)
1-ch audio talk input 200-3000mv 10KΩ(BNC)
1-ch audio talk output 200-3000mv 5KΩ(BNC)
4 built-in SATA port. Support 4 HDDs.
AudioPCM 28.8MByte/h
Video56-900MByte/h
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback
and reverse play mode.
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when a file is end system auto plays the
next file in the current channel
There is 1/4/9/16-channel playback mode.
(It may vary due to different series.)
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone
to activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk, USB
burner and etc.)
Support peripheral eSATA backup device.
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
4-ch 200-2000mv 10K(BNC)
4-ch 200-2000mv 10K(BNC)
7
Page 18
Network Function
Motion Detection and Alarm
Interface
System Information
User Management
Upgrade Login, Logout and Shutdown
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm Manual Alarm Control
Alarm Input
Alarm Output
Alarm Relay USB
Interface Network connection
RS485
RS232
Hard Disk Information Data Stream Statistics Log statistics
Version
On-line user Display current on-line user
User Manageme nt
Password Authenticati on
View alarm information such as external alarm, motion detection and
video loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Duplex transparent COM
Network alarm input and output
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Support record activation function or activate external alarm or screen
message in specified period.
Enable or disable alarm input channel
Support analog alarm signal to specific alarm output channel.
4-ch alarm input(You
can set normal open or
normal close type to
select the alarm type.
6-channel relay output, including one controllable DC +12V output port.
30V DC 2A125V AC 1A(activation alarm
2 USB 2.0 ports.
RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port
Support various PTZ control protocols.
Ordinary COM (Debug),keyboard connection and transparent serial
port(COM input and output via network )
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, alarm input and output
amount, system version and release date.
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
8-ch alarm input(You can set normal open or normal close type to select the alarm type.
16-ch alarm input You can set normal open or normal close type to select the alarm type.
8
Page 19
Right authentication when shut down to make sure only those proper
people can turn off DVR
General Parameter
Power Power
Consumptio n Working
AC90~264V 50+2% Hz Max 75W
25W (Exclude HDD)
0℃-+55 Temperatur e
Working
10%90% Humidity
Air
86kpa106kpa Pressure
Dimension
1.5U standard industrial case. 440(W) x410 (D) x70mm(H)
Weight 4.5-5.5KG(Exclude HDD) Installation
Desktop/rack installation Mode
1.3.3 Simple 1.5 U
System
Parameter
Main Processor
4-ch 8-ch 16-ch
High-performance industrial embedded micro controller
Compression Standard
Video monitor
OS System
Resources Interface Input
Devices Input Method Shortcut Function Video Compressio n Audio Compressio n
Video Input
Video Output
Video Standard
Record Speed
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback
and network operation simultaneously
User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese
(optional)
Copy/paste operation, USB mouse right-key shortcut menu, double click
USB mouse to switch screen.
H.264
G.711A
4-CH composite video
input: (NTSC/PAL)
B
BNC (1.0V
P- P,
B75)
8-CH composite video input: (NTSC/PAL)
B
BNC (1.0V
P- P,
B75)
16-CH composite video input: (NTSC/PAL) BNC
B
P- P,
B75)
(1.0V
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output.
1-ch VGA output.
1-ch HDMI output.
1-ch matrix output.
Support TV/VGA/HDMI video output at the same time.
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s
per channel
Video Partition
1/4 windows(Optional) 1/4/8/9 windows 1/4/8/9 /16 windows
9
Page 20
Monitor Touring
Resolution (PAL/NTSC )
Image Quality Privacy mask Image Information
TV Adjust Adjust TV output zone suitable to anamorphic video.
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL/NTSC
Real-time monitor
D1 704×576/704×480
Playback channel 1/16
D1 704×576/704×480 ;
HD1 704×288/704×240;
BCIF 352×576/352×480;
CIF 352×288/ 352×240;
QCIF 176×144/176×120
Support dual streams.
Extra stream resolution:
CIF 352×288/ 352×240
QCIF 176×144/176×120
6-level image quality (Adjustable)
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
Channel information, time information and privacy mask zone.
Audio
Hard disk
Record and playback
Channel Lock
Channel Information
Color Configuratio n
Audio Input
Audio Output
Bidirectional Audio
Hard Disk Hard Disk
Occupation
Recording Mode
Recording Length Playback Repeat Way
Record Search Playback Mode
Cover secret channel with black screen though system is encoding
normally.
Screen-lock function to prevent unauthorized user seeing secret video.
Channel name, recording status, screen lock status, video loss status
and motion detection status are shown on the bottom left of display
screen.
Hue, brightness, contrast, saturation and gain setup for each channel.
4-ch 200-2000mv
10K(BNC)
1-ch audio output 200-3000mv 5K(BNC) 1-ch audio output
1-ch audio talk output 200-3000mv 5K(BNC) 1-ch audio output
2 built-in SATA port. Support 2 HDDs.
AudioPCM 28.8MByte/h
Video56-900MByte/h
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback
and reverse play mode.
8-ch 200-2000mv 10K(BNC)
4-ch 200-2000mv 10K (RCA)
200-3000mv 5K(RCA)
200-3000mv 5K(RCA)
10
Page 21
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when a file is end system auto plays the
next file in the current channel
There is 1/4/9/16-channel playback mode.
(It may vary due to different series.)
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone
to activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk, USB
burner and etc.)
Support peripheral eSATA backup device.
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and
video loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Duplex transparent COM
Network alarm input and output
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Support record activation function or activate external alarm or screen
message in specified period.
Enable or disable alarm input channel
Support analog alarm signal to specific alarm output channel.
4-ch alarm input(You
can set normal open or
normal close type to
select the alarm type.
3-channel relay output (The upper limit for rated current is 800mA )
30V DC 2A, 125V AC 1A(activation alarm
2 USB 2.0 ports.
RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port
Support various PTZ control protocols.
Ordinary COM (Debug),keyboard connection and transparent serial
port(COM input and output via network )
Display HDD current status
Backup function
Network Function
Motion Detection and Alarm
Interface
System Information
Various File Switch Ways
Multi­channel Playback Window Zoom Partial Enlargemen t
Backup Mode
Network control
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm Manual Alarm Control
Alarm Input
Alarm Output
Alarm Relay USB
Interface Network connection
RS485
RS232
Hard Disk Information
8-ch alarm input(You can set normal open or normal close type to select the alarm type.
16-ch alarm input You can set normal open or normal close type to select the alarm type.
11
Page 22
Data Stream Statistics Log statistics
Version
On-line user Display current on-line user
User Management
Upgrade
Login, Logout and Shutdown
General Parameter
User Manageme nt
Password Authenticati on
Power Power
Consumptio n
Working Temperatur e Working Humidity Air Pressure
Dimension Weight
Installation Mode
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, alarm input and output
amount, system version and release date.
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
Right authentication when shut down to make sure only those proper
people can turn off DVR
DC 12V
25W (Include adapter; Exclude HDD)
0℃-+55
10%90%
86kpa106kpa
1.5U standard industrial case. 440(W) x410 (D) x70mm(H)
3.94.5KG (Exclude HDD)
Desktop
1.3.4 2U Series
System
Parameter
Main Processor
4-ch 8-ch 16-ch 24-ch 32-ch
High-performance industrial embedded micro controller
OS System
Resources Interface
Input Devices
Input Method
Shortcut Function
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback and network operation simultaneously User-friendly graphical user interface
Front panel, USB mouse, remote control Arabic number, English character, donation and extension Chinese
(optional) Copy/paste operation, USB mouse right-key shortcut menu, double click USB mouse to switch screen.
12
Page 23
Compression Standard
Video Compression
H.264
Video monitor
Audio Compression
Video Input
G.711A
4-CH composite video input: (NTSC/PAL ) BNC
B
(1.0V
P- P,
B75)
8-CH composite video input: (NTSC/PAL ) BNC
B
(1.0V
P- P,
B75)
16-CH composite video input: (NTSC/PAL ) BNC
B
(1.0V
P- P,
B75)
24H composite video input: (NTSC/PAL ) BNC
B
(1.0V
P- P,
B75)
32H composite video input: (NTSC/PAL ) BNC (1.0V
B75)
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output. 1-ch VGA output.
Video Output
1-ch HDMI output. 1-ch matrix output.
Support TV/VGA/HDMI video output at the same time. Video Standard
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s Record Speed
Video Partition
Monitor Touring
per channel
1/4
windows(O
ptional)
1/4/8/9 windows
1/4/8/9 /16 windows
1/4/8/9 /16/25 windows
1/4/8/9 /16/25/36
windows Support monitor tour functions such as alarm, motion detection, and schedule auto control. PAL/NTSC Real-time monitor D1 704×576/704×480
Playback channel 1/16
Resolution (PAL/NTSC)
D1 704×576/704×480 CIF 352×288/ 352×240 QCIF 176×144/176×120 Support dual streams.
Extra stream resolution: CIF 352×288/ 352×240 QCIF 176×144/176×120
Image Quality
6-level image quality (Adjustable)
Privacy mask Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
Image Information
Channel information, time information and privacy mask zone.
B
P- P,
Audio
TV Adjust Adjust TV output zone suitable to anamorphic video.
Channel Lock Cover secret channel with black screen though system is encoding
normally. Screen-lock function to prevent unauthorized user seeing secret video.
Channel Information
Channel name, recording status, screen lock status, video loss status and motion detection status are shown on the bottom left of display screen.
Color
Hue, brightness, contrast, saturation and gain setup for each channel.
Configuration
Bidirectional Audio
Hard Disk
1-ch audio talk input 200-3000mv 10K(BNC) 1-ch audio talk output 200-3000mv 5KΩ(BNC)
8 built-in SATA port. Support 8 HDDs.
13
Page 24
Hard disk
Record and playback
Backup function
Network Function
Motion Detection and Alarm
Hard Disk Occupation
Recording Mode
Recording Length Playback Repeat Way
Record Search Various search engines such as time, type and channel.
Playback Mode Various File Switch Ways
Multi-channel Playback
Window Zoom Switch between self-adaptive screen/full screen when playback
Partial Enlargement
Backup Mode
Network control
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm Support record activation function or activate external alarm or screen
Manual Alarm Control
AudioPCM 28.8MByte/h Video56-900MByte/h Manual recording, motion detection recording, schedule recording and
alarm recording Priority: Manual recording> alarm recording>motion detection recording>schedule recording. 1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various fast play, slow play speeds, manual frame by frame playback and reverse play mode. Can switch to previous or next file or any file in current play list. Can switch to file on other channel of the same time. (If there is a file) Support file continuous play, when a file is end system auto plays the next file in the current channel There is 1/4/9/16-channel playback mode. (It may vary due to different series.)
When in one-window full-screen playback mode, you can select any zone to activate partial enlargement function. HDD backup Support peripheral USB backup device. (Flash disk, portable disk, USB burner and etc.) Support peripheral eSATA backup device. Support network download and backup View monitor channel remotely.
DVR configuration through client-end and web browser Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and video loss via client. Support network PTZ lens control File download backup and playback Multiple devices share information via corresponding software such as professional surveillance software (PSS) Duplex transparent COM Network alarm input and output Bidirectional audio. Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones. Various sensitivity levels. Alarm can activate record or external alarm or screen message prompt.
message in specified period. Enable or disable alarm input channel Support analog alarm signal to specific alarm output channel.
14
Page 25
4-ch alarm inputYou can set normal
Alarm Input
Alarm Output
Alarm Relay
Interface
System Information
User Management
Upgrade
Login, Logout and Shutdown
General Parameter
USB Interface 3 USB 2.0 ports. Network connection
RS485
RS232
Hard Disk Information Data Stream Statistics
Log statistics
Version
On-line user Display current on-line user
User Management
Password Authentication
Power Power
Consumption
Working Temperature
open or normal close type to select the alarm type.
6-channel relay output, including one controllable DC +12V output port.
30V DC 2A125V AC 1A(activation alarm
RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port Support various PTZ control protocols. Ordinary COM (Debug),keyboard connection and transparent serial port(COM input and output via network ) Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files. Support various search engines such as time and type. Display version information: channel amount, alarm input and output amount, system version and release date.
Multi-lever user management; various management modes Integrated management for local user, serial port user and network user. Configurable user power. Support user /group and its corresponding rights modification. No limit to the user or group amount. Password modification Administrator can modify other user’s password. Account lock strategy Five times login failure in thirty minutes may result in account lock. Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout /shutdown/ restart. Right authentication when shut down to make sure only those proper people can turn off DVR
AC90~264V 50+2% Hz Max 220W
25W (Exclude HDD)
0℃-+55
8-ch alarm inputYou can set normal open or normal close type to select the alarm type. 6-channel relay output, including one controllable DC +12V output port.
16-ch alarm inputYou can set normal open or normal close type to select the alarm type. 6-channel relay output, including one controllable DC +12V output port.
16-ch alarm inputYou can set normal open or normal close type to select the alarm type. 5-channel relay output. including one controllable DC +12V output port.
16-ch alarm
inputYou
can set
normal
open or
normal
close type
to select the
alarm
type.
5-channel
relay
output
including
one
controllable
DC +12V
output port.
15
Page 26
Working Humidity
Air Pressure Dimension Weight 6.5-7.5KG(Exclude HDD)
Installation Mode
10%90%
86kpa106kpa 2U standard industrial case. 440(W) x460 (D) x89mm(H)
Desktop/rack installation
1.3.5 2U Series HD-SDI series
System
Parameter
Main Processor
4-ch
High-performance industrial embedded micro controller
Compression Standard
Video monitor
OS System
Resources Interface Input
Devices Input Method Shortcut Function Video Compressio n Audio Compressio n
Video Input
Video Output
Video Standard
Record Speed
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback and network operation simultaneously User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese (optional) Copy/paste operation, USB mouse right-key shortcut menu, double click USB mouse to switch screen.
H.264
G.711A
4-CH composite video input: (NTSC/PAL) BNC (1.0V
B
P- P,
B75)
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output. 1-ch VGA output. 1-ch HDMI output. Support TV/VGA/HDMI video output at the same time.
PAL (50f/s), NTSC (60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per channel
Video Partition Monitor Touring
Resolution (PAL/NTSC )
Image Quality
1/4 windows
Support monitor tour functions such as alarm, motion detection, and schedule auto control.
PAL(50f/s)NTSC(60f/s) Real time 1080P(1920*1080) Recording playback channel1/4: 1080P 1920*1080 720P 1280*720 D1 704×576/704×480 ; CIF 352×288/ 352×240; QCIF 176×144/176×120 Dual-stream supported: Extra stream resolution1080P 1920*1080 720P 1280*720 D1 704×576/704×480 ;CIF 352×288/ 352×240 ; QCIF 176×144/176×120 6-level image quality (Adjustable)
16
Page 27
Privacy mask Image Information
TV Adjust Adjust TV output zone suitable to anamorphic video.
Support one privacy mask of user-defined size in full screen. Support max 4 zones.
Channel information, time information and privacy mask zone.
Audio
Hard disk
Record and playback
Backup function
Channel Lock
Channel Information
Color Configuratio n
Audio Input
Audio Output
Bidirectional Audio
Hard Disk Hard Disk
Occupation
Recording Mode
Recording Length Playback Repeat Way
Record Search Playback Mode Various File Switch Ways
Multi­channel Playback Window Zoom Partial Enlargemen t
Backup Mode
Network control
Cover secret channel with black screen though system is encoding normally. Screen-lock function to prevent unauthorized user seeing secret video. Channel name, recording status, screen lock status, video loss status and motion detection status are shown on the bottom left of display screen. Hue, brightness, contrast, saturation and gain setup for each channel.
4-ch 200-2000mv 10KΩ(BNC) 1-ch audio output 200-3000mv 5KΩ(BNC)
1-ch audio talk output 200-3000mv 5KΩ(BNC)
8 built-in SATA port. Support 8 HDDs. AudioPCM 28.8MByte/h
Video56-3600MByte/h Manual recording, motion detection recording, schedule recording and
alarm recording Priority: Manual recording> alarm recording>motion detection recording>schedule recording. 1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback and reverse play mode. Can switch to previous or next file or any file in current play list. Can switch to file on other channel of the same time. (If there is a file) Support file continuous play, when a file is end system auto plays the next file in the current channel There is 1/4/-channel playback mode.
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone to activate partial enlargement function.
HDD backup Support peripheral USB backup device. (Flash disk, portable disk, USB burner and etc.) Support peripheral eSATA backup device. Support network download and backup View monitor channel remotely.
DVR configuration through client-end and web browser Upgrade via client or browser to realize remote maintenance.
17
Page 28
Network Function
Motion Detection and Alarm
Interface
System Information
User Management
Upgrade Login, Logout and Shutdown
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm Manual Alarm Control
Alarm Input
Alarm Output
Alarm Relay USB
Interface Network connection
RS485
RS232
Hard Disk Information Data Stream Statistics Log statistics
Version
On-line user Display current on-line user
User Manageme nt
Password Authenticati on
View alarm information such as external alarm, motion detection and video loss via client. Support network PTZ lens control File download backup and playback Multiple devices share information via corresponding software such as professional surveillance software (PSS) Duplex transparent COM Network alarm input and output Bidirectional audio. Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones. Various sensitivity levels. Alarm can activate record or external alarm or screen message prompt.
Support record activation function or activate external alarm or screen message in specified period. Enable or disable alarm input channel Support analog alarm signal to specific alarm output channel.
4-ch alarm input(You can set normal open or normal close type to select the alarm type.
6-channel relay output, including one controllable DC +12V output port.
30V DC 2A125V AC 1A(activation alarm 3 USB 2.0 ports.
RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port Support various PTZ control protocols. Ordinary COM (Debug),keyboard connection and transparent serial port(COM input and output via network ) Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files. Support various search engines such as time and type. Display version information: channel amount, alarm input and output amount, system version and release date.
Multi-lever user management; various management modes Integrated management for local user, serial port user and network user. Configurable user power. Support user /group and its corresponding rights modification. No limit to the user or group amount. Password modification Administrator can modify other user’s password. Account lock strategy Five times login failure in thirty minutes may result in account lock. Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout /shutdown/ restart.
8-ch alarm input(You can set normal open or normal close type to select the alarm type.
16-ch alarm input You can set normal open or normal close type to select the alarm type.
18
Page 29
Right authentication when shut down to make sure only those proper people can turn off DVR
General Parameter
Power Power
Consumptio n
AC90~264V 50+2% Hz Max 220W
50W (Exclude HDD)
Working
0℃-+55
Temperatur e Working
10%90%
Humidity Air
86kpa106kpa
Pressure Dimension
Weight Installation
2U standard industrial case. 440(W) x460 (D) x89mm(H)
7.08.0KG (Exclude HDD) Desktop/rack installation
Mode
1.3.5 2U Series 960H series
System
Parameter
Main Processor
4-ch 8-ch 16-ch
High-performance industrial embedded micro controller
Compression Standard
Video monitor
OS System
Resources Interface
Input Devices
Input Method
Shortcut Function
Video Compression
Audio Compression
Video Input
Video Output
Video Standard
Record Speed
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback and network operation simultaneously User-friendly graphical user interface
Front panel, USB mouse, remote control Arabic number, English character, donation and extension Chinese
(optional) Copy/paste operation, USB mouse right-key shortcut menu, double click USB mouse to switch screen.
H.264
G.711A
4-CH composite video input: (NTSC/PAL) BNC
B
P- P,
B75)
(1.0V
8-CH composite video input: (NTSC/PAL)
B
BNC (1.0V
P- P,
B75)
16-CH composite video input: (NTSC/PAL) BNC
B
P- P,
B75)
(1.0V
1-ch PAL/NTSC, BNC (1.0VP- P, 75) composite video signal output. 1-ch VGA output. 1-ch HDMI output. 1-ch matrix output. Support TV/VGA/HDMI video output at the same time.
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per channel
Video Partition
1/4 windows(Optional)
1/4/8/9 windows 1/4/8/9 /16 windows
19
Page 30
Monitor Touring
Resolution (PAL/NTSC)
Image Quality Privacy mask Support one privacy mask of user-defined size in full screen.
Image Information
TV Adjust Adjust TV output zone suitable to anamorphic video.
Channel Lock Cover secret channel with black screen though system is encoding
Channel Information
Color Configuration
Audio
Audio Input
Audio Output
Support monitor tour functions such as alarm, motion detection, and schedule auto control. PAL(625TVL, 50f/s)/NTSC(525TVL, 60f/s) Real-time monitor 960H 960 ×576/960×480
Playback channel 1/16 960 ×576/960×480 D1 704×576/704×480 CIF 352×288/ 352×240 QCIF 176×144/176×120
Support dual streams. Extra stream resolution: CIF 352×288/ 352×240 QCIF 176×144/176×120 6-level image quality (Adjustable)
Support max 4 zones.
Channel information, time information and privacy mask zone.
normally. Screen-lock function to prevent unauthorized user seeing secret video. Channel name, recording status, screen lock status, video loss status and motion detection status are shown on the bottom left of display screen. Hue, brightness, contrast, saturation and gain setup for each channel.
4-ch 200-2000mv 10K(BNC)
1-ch audio output 200-3000mv 5KΩ(BNC)
8-ch 200-2000mv 10K(BNC)
16-ch 200­2000mv 10K (BNC)
Hard disk
Record and playback
Bidirectional Audio
Hard Disk Hard Disk
Occupation
Recording Mode
Recording Length Playback Repeat Way
Record Search Various search engines such as time, type and channel.
Playback Mode Various File Switch Ways
1-ch audio talk input 200-3000mv 10K(BNC) 1-ch audio talk output 200-3000mv 5KΩ(BNC) 8 built-in SATA port. Support 8 HDDs.
AudioPCM 28.8MByte/h Video56-900MByte/h Manual recording, motion detection recording, schedule recording and
alarm recording Priority: Manual recording> alarm recording>motion detection recording>schedule recording. 1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various fast play, slow play speeds, manual frame by frame playback and reverse play mode. Can switch to previous or next file or any file in current play list. Can switch to file on other channel of the same time. (If there is a file) Support file continuous play, when a file is end system auto plays the next file in the current channel
20
Page 31
There is 1/4/9/16-channel playback mode. (It may vary due to different series.)
When in one-window full-screen playback mode, you can select any zone to activate partial enlargement function. HDD backup Support peripheral USB backup device. (Flash disk, portable disk, USB burner and etc.) Support peripheral eSATA backup device. Support network download and backup View monitor channel remotely.
DVR configuration through client-end and web browser Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and video loss via client. Support network PTZ lens control File download backup and playback Multiple devices share information via corresponding software such as professional surveillance software (PSS) Duplex transparent COM Network alarm input and output Bidirectional audio. Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones. Various sensitivity levels. Alarm can activate record or external alarm or screen message prompt.
message in specified period. Enable or disable alarm input channel Support analog alarm signal to specific alarm output channel. 4-ch alarm input(You can set normal open or normal close type to select the alarm type.
6-channel relay output, including one controllable DC +12V output port.
30V DC 2A125V AC 1A(activation alarm
2 RJ45 10M/100M/1000M self-adaptable Ethernet port
PTZ control port Support various PTZ control protocols. Ordinary COM (Debug),keyboard connection and transparent serial port(COM input and output via network ) Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files. Support various search engines such as time and type. Display version information: channel amount, alarm input and output amount, system version and release date.
Backup function
Network Function
Motion Detection and Alarm
Interface
System Information
Multi-channel Playback
Window Zoom Switch between self-adaptive screen/full screen when playback
Partial Enlargement
Backup Mode
Network control
Motion Detection
Video Loss Alarm can activate external alarm or screen message prompt. External Alarm Support record activation function or activate external alarm or screen
Manual Alarm Control
Alarm Input
Alarm Output
Alarm Relay USB Interface 3 USB 2.0 ports. Network
connection
RS485
RS232
Hard Disk Information Data Stream Statistics
Log statistics
Version
On-line user Display current on-line user
8-ch alarm input(You can set normal open or normal close type to select the alarm type.
16-ch alarm input You can set normal open or normal close type to select the alarm type.
21
Page 32
User Management
User Management
Password Authentication
Upgrade
Login, Logout and Shutdown
General Parameter
Power Power
Consumption
Working Temperature Working Humidity
Air Pressure Dimension Weight 6.5-7.5KG(Exclude HDD)
Installation Mode
Multi-lever user management; various management modes Integrated management for local user, serial port user and network user. Configurable user power. Support user /group and its corresponding rights modification. No limit to the user or group amount. Password modification Administrator can modify other user’s password. Account lock strategy Five times login failure in thirty minutes may result in account lock. Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout /shutdown/ restart. Right authentication when shut down to make sure only those proper people can turn off DVR
AC90~264V 50+2% Hz Max 220W
25W (Exclude HDD)
0℃-+55
10%90%
86kpa106kpa 2U standard industrial case. 440(W) x460 (D) x89mm(H)
Desktop/rack installation
22
Page 33
2 Overview and Controls
This section provides information about front panel and rear panel. When you install this series
DVR for the first time, please refer to this part first.
2.1 Front Panel
2.1.1 1U series
The front panel is shown as in Figure 2-1.
Figure 2-1
Please refer to the following sheet for front panel button information.
Name Icon Function
Power button, press this button for three seconds to boot up
Power button
or shut down DVR.
Shift Shift
Up/1 Down/4
Left/2 Right/3
ESC ESC
Enter ENTER
ST
W X
In textbox, click this button to switch between numeral, English(Small/Capitalized),donation and etc.
Activate current control, modify setup, and then move up and down.
Increase/decrease numeral.
Assistant function such as PTZ menu.
In text mode, input number 1/4 (English character G/H/I)
Shift current activated control,
When playback, click these buttons to control playback bar. In text mode, input number 2(English character A/B/C) /3(English character D/E/F)
Go to previous menu, or cancel current operation.
When playback, click it to restore real-time monitor mode.
Confirm current operation
Go to default button
Record REC
Slow play/8
Assistant Fn
Go to menu
Manually stop/start recording, working with direction keys or numeral keys to select the recording channel.
Multiple slow play speeds or normal playback. In text mode, input number 8 (English character T/U/V).
One-window monitor mode, click this button to display assistant function: PTZ control and image color.
23
Page 34
Backspace function: in numeral control or text control, press it for 1.5seconds to delete the previous character before the cursor.
In motion detection setup, working with Fn and direction keys to realize setup.
In text mode, click it to switch between numeral, English character(small/capitalized) and etc.
Realize other special functions.
Fast play/7
Play previous/0
Reverse/Pau se/6
Play Next/9
Play/Pause /5
USB port
Network abnormal indication light
W
f
Net
_
f
Various fast speeds and normal playback. In text mode, input number 7 (English character P/Q/R/S).
In playback mode, playback the previous video In text mode, input number 0.
In normal playback or pause mode, click this button to reverse playback In reverse playback, click this button to pause playback. In text mode, input number 6 (English character M/N/O)
In playback mode, playback the next video In menu setup, go to down ward of the dropdown list. In text mode, input number 9 (English character W/X/Y/Z)
In normal playback click this button to pause playback In pause mode, click this button to resume playback. In text mode, input number 5(English character J/K/L).
To connect USB storage device, USB mouse.
Network error occurs or there is no network connection, the light becomes red to alert you.
HDD abnormal indication light
Record light 1-16
IR Receiver IR
Alarm indication light
HDD
Alarm
HDD error occurs or HDD capacity is below specified threshold value, the light becomes red to alert you.
System is recording or not. It becomes on when system is recording.
It is to receive the signal from the remote control.
Here you can view there is external alarm input or not. The light becomes on when there is an external alarm. The light become off when the external alarm stops.
2.1.2 1.5U series
The front panel is shown as below. See Figure 2-2.
24
Page 35
Figure 2-2
Please refer to the following sheet for front panel button information.
Name Icon Function
Power button
USB port
Up/ Down
ST
Power button, press this button for three seconds to boot up or shut down DVR.
To connect USB storage device, USB mouse.
Activate current control, modify setup, and then move up and down.
Increase/decrease numeral.
Assistant function such as PTZ menu.
Input number 1/4.
Left/ Right
Enter ENTER
Reverse/Pau se
Play/Pause
Slow play
Fast play
Play previous
W X
W
f
I_
Shift current activated control, and then move left and right.
When playback, click these buttons to control playback bar.
Input number 2/3.
Confirm current operation
Go to default button
Go to menu
In normal playback or pause mode, click this button to reverse Playback Input number 5. In normal playback click this button to pause playback In pause mode, click this button to resume playback. Input number 6.
Multiple slow play speeds or normal playback. Input number 8.
Various fast speeds and normal playback. Input number 7.
In playback mode, playback the previous video. Input number 9.
Play Next
ESC ESC
Assistant Fn
`I
In playback mode, playback the next video Input number 0.
Go to previous menu, or cancel current operation.
When playback, click it to restore real-time monitor mode.
One-window monitor mode, click this button to display assistant function: PTZ control and image color.
25
Page 36
Backspace function: in numeral control or text control, press it for 1.5 seconds to delete the previous character before the cursor. In motion detection setup, working with Fn and direction keys to realize setup. In text mode, click it to switch between numeral, English character(small/capitalized) and etc. In HDD management interface, you can click it to switch HDD record information and other information (Menu prompt) Realize other special functions.
Shift
Record REC
Remote control indication light
ACT Remote control indication light
In textbox, click this button to switch between numeral, English(Small/Capitalized),donation and etc.
Manually stop/start recording, working with direction keys or numeral keys to select the recording channel.
Status indication light
Power indication light
Record light 1-16
IR Receiver IR
CD-ROM button
Note: the front panel of simple 1.5U also adopts the above panel model.
Status
Power Power indication light
If there is Fn indication light, current status indication light is null.
System is recording or not. It becomes on when system is recording.
It is to receive the signal from the remote control.
Pop-up or insert the CD.
2.1.3 2U series (HD-SDI series, 960H included)
The front panel of general series is shown as in Figure 2-3.
Figure 2-3
The Front panel of HD-SDI series and 960H series is shown as follows. See Figure 2-4.
26
Page 37
Figure 2-4
Please refer to the following sheet for front panel button information.
Name Icon Function
Power button
Number button 0-9
Input number more than 10
Shift
Up/ Down
Left/ Right
ESC ESC
-/--
ST
W X
Power button, press this button for three seconds to boot up or shut down DVR.
Input Arabic number Switch channel
If you want to input a number more than 10, please click this button and then input.
In textbox, click this button to switch between numeral, English(Small/Capitalized),donation and etc.
Enable or disable tour. Activate current control, modify setup, and then move up and
down.
Increase/decrease numeral.
Assistant function such as PTZ menu.
Shift current activated control, and then move left and right.
When playback, click these buttons to control playback bar.
Go to previous menu, or cancel current operation.
When playback, click it to restore real-time monitor mode.
Confirm current operation
Enter ENTER
Record REC
Slow play
Assistant Fn
Go to default button
Go to menu
Manually stop/start recording, working with direction keys or numeral keys to select the recording channel.
Multiple slow play speeds or normal playback.
One-window monitor mode, click this button to display assistant function: PTZ control and image color.
Backspace function: in numeral control or text control, press it for 1.5seconds to delete the previous character before the cursor.
27
Page 38
In motion detection setup, working with Fn and direction keys to realize setup.
In text mode, click it to switch between numeral, English character(small/capitalized) and etc.
In HDD management interface, you can click it to switch HDD record information and other information (Menu prompt)
Realize other special functions.
Fast play
Play previous
Reverse/Pause
Play Next
Play/Pause
Window switch Mult Click it to switch one-window/multiple-window.
Shuttle(outer ring)
Jog(inner dial)
_
W
f
f
Various fast speeds and normal playback.
In playback mode, playback the previous video
In normal playback or pause mode, click this button to reverse playback In reverse playback, click this button to pause playback.
In playback mode, playback the next video In menu setup, go to down ward of the dropdown list.
In normal playback click this button to pause playback In pause mode, click this button to resume playback.
In real-time monitor mode it works as left/right direction key. Playback mode, counter clockwise to forward and clock wise to backward. Up/down direction key. Playback mode, turn the inner dial to realized frame by frame playback. (Only applies to some special versions.)
USB port
Remote control indication light
Status indication light
Power indication light
Record light 1-32 It becomes on when system is recording.
IR Receiver IR It is to receive the signal from the remote control.
ACT Remote control indication light
Status If there is Fn indication light, current status indication light is null.
PWR Power indication light
To connect USB storage device, USB mouse.
28
Page 39
2.2 Rear Panel
2.2.1 1U series
The 4/8-channel series DVR rear panel is shown as below. See Figure 2-5.
Figure 2-5
The 16-channel series DVR rear panel is shown as below. See Figure 2-6.
Figure 2-6
Please refer to the following sheet for detailed information.
1 Video input 2 Audio input 3 Video spot output 4 Video CVBS output 5 Bidirectional talk input 6 Audio output 7 Network port 8 USB port 9 HDMI port 10 Video VGA output 11 RS232 port 12 Alarm input/alarm output/RS485 port 13 Power socket
14 GND port 15 On/off button
2.2.2 1.5U series
The rear panel is shown as in Figure 2-7.
29
Page 40
Figure 2-7
Please refer to the following sheet for detailed information.
1 GND port 2 Power input port 3 Power button 4 Fan 5 Audio input /Matrix video output/Loop video
output 6 Video input 7 Video CVBS output 8 Bidirectional talk input port 9 Bidirectional talk output port 10 Audio output 11 Alarm input/Alarm output/RS485 port 12 Video VGA output
13 HDMI port
14 RS232 port 15 eSATA port
16 USB port
17 Network port
2.2.3 Simple 1.5U
This series DVR rear panel is shown as below. See Figure 2-8.
Figure 2-8
Please refer to the following sheet for detailed information.
1 Video input 2 Video spot output 3 Video CVBS output 4 Audio input 5 Bidirectional talk input 6 Audio output 7 Network port 8 USB port
30
Page 41
9 HDMI port 10 Video VGA output 11 RS232 port 12 Alarm input/alarm output/RS485 port 13 On/off button 14 Power socket 15 GND port
2.2.4 2U series
This series DVR rear panel is shown as below. See Figure
2-9
Figure 2-9
Please refer to the following sheet for detailed information.
1 GND port 2 Power input port 3 Power button 4 Fan 5 DB25 port ( 5th to 16th-channel audio input port) 6 1st to 4th-channel audio input 7 Loop video output 8 Video input 9 Video CVBS output 10 Matrix video output 11 Audio output 12 Bidirectional talk input port
13 Bidirectional talk output port
14 Alarm input/Alarm output/RS485 port HDMI
port 15 Video VGA output
16 HDMI port
17 Video CVBS output RS232 port
18 Video matrix output eSATA port 19 USB port 20 Network port
2.2.5 2U series (HD-SDI series)
31
Page 42
Figure 2-10
Please refer to the following sheet for detailed information.
1 GND port 2 Power input port 3 Power button 4 Fan 5 Video input 6 Loop video output 7 Audio input 8 Bidirectional talk input port 9 Bidirectional talk output port 10 Video output 11 Audio output 12 Alarm input/Alarm output/RS485 port HDMI
port 13 Network port
14 Video VGA output 15 HDMI port
16 USB port
17 eSATA port
18 Video CVBS output RS232 port
2.2.5 2U series (960H series)
The rear panel is shown as in Figure 2-11.
Figure 2-11
Please refer to the following sheet for detailed information.
32
Page 43
1 GND port 2 Power input port 3 Power button 4 Fan 5 DB25 port (5-16 channel audio input) 6 1-4channel audio input 7 Loop video output 8 Video input 9 Video CVBS output 10 Matrix video output 11 Audio output 12 Bidirectional talk input port
13 Bidirectional talk output port
14 Alarm input/Alarm output/RS485 port 15 Video VGA output
16 HDMI port
17 RS-232
18 eSATA port
19 USB port 20 Network port
When connect the Ethernet port, please use crossover cable to connect the PC and use the
straight cable to connect to the switcher or router.
2.3 Connection Sample
2.3.1 1U series
Please refer to Figure 2-12 for connection sample.
The following figure is based on the 8-channel series product.
33
Page 44
2.3.2 1.5U series
Please refer to Figure 2-13 for connection sample.
Figure 2-12
34
Page 45
Figure 2-13
Note: There are slight differences for simple 1.5U connection.
2.3.3 2U series
Please refer to Figure 2-14 for connection sample.
35
Page 46
Figure 2-14
36
Page 47
2.3.4 2U series (HD-SDI series)
Please refer to the following figure for detailed information. See Figure 2-15.
Figure 2-15
2.3.4 2U series (960H series)
Please refer to the following figure for detailed information. See Figure 2-16.
37
Page 48
Figure 2-16
2.4 Remote Control
The remote control interface is shown as in Figure 2-17.
Please note remote control is not our standard accessory and it is not included in the accessory
bag.
38
Page 49
Figure 2-17
Please refer to the following sheet for detailed information.
Serial Number Name Function 1 Power button Click it to boot up or shut down
the device.
2 Address Click it to input device number,
so that you can control it.
3 Forward Various forward speeds and
normal speed playback.
4 Slow play Multiple slow play speeds or
normal playback.
5
6 7 Play/Pause
8
Next record In playback mode, playback the
next video.
Previous record In playback mode, playback the
previous video. In pause mode, click this button to realize normal playback. In normal playback click this button to pause playback. In real-time monitor mode, click this button to enter video search menu.
Reverse/pause
Reverse playback pause mode, click this button to realize normal playback. In reverse playback click this button to pause playback.
39
Page 50
9
10 Record Start or stop record manually
11 Direction keys Switch current activated control,
12 Confirm /menu key go to default button
13 Multiple-window switch Switch between multiple-window
14 Auxiliary key
15 0-9 number key
Cancel Go back to previous menu or
cancel current operation (close upper interface or control)
In record interface, working with the direction buttons to select the record channel. Click this button for at least 1.5 seconds, system can go to the Manual Record interface.
go to left or right. In playback mode, it is to control the playback process bar. Aux function(such as switch the PTZ menu)
go to the menu
and one-window. In 1-ch monitor mode: pop up assistant functionPTZ control and Video color. Switch the PTZ control menu in PTZ control interface. In motion detection interface, working with direction keys to complete setup. Input password, channel or switch channel. Shift is the button to switch the input method.
2.5 Mouse Control
Left click mouse
System pops up password input dialogue box if you have not logged in. In real-time monitor mode, you can go to the main menu. When you have selected one menu item, left click mouse to view menu content. Implement the control operation.
Modify checkbox or motion detection status. Click combo box to pop up drop down list
40
Page 51
In input box, you can select input methods. Left click the corresponding button on the panel you can input numeral/English character (small/capitalized). Here stands for backspace button. _ stands for space button.
In English input mode: _stands for input a backspace icon and stands for deleting the previous character.
Double left click mouse
Right click mouse
In numeral input mode: _ stands for clear and stands for deleting the previous numeral.
When input special sign, you can click corresponding numeral in the front panel to input. For example, click numeral 1 you can input“/” , or you can click the numeral in the on-screen keyboard directly.
Implement special control operation such as double click one item in the file list to playback the video. In multiple-window mode, double left click one channel to view in full-window. Double left click current video again to go back to previous multiple-window mode. In real-time monitor mode, pops up shortcut menu: one-window, four-window, nine-window and sixteen-window, Pan/Tilt/Zoom, color setting, search, record, alarm input, alarm output, main menu. Among which, Pan/Tilt/Zoom and color setting applies for current selected channel. If you are in multiple-window mode, system automatically switches to the corresponding channel.
Press middle button
Move mouse
Exit current menu without saving the modification. In numeral input box: Increase or decrease numeral value. Switch the items in the check box. Page up or page down Select current control or move control
Select motion detection zone Drag mouse
Select privacy mask zone.
41
Page 52
2.6 Virtual Keyboard & Front Panel
2.6.1 Virtual Keyboard
The system supports two input methods: numeral input and English character (small and
capitalized) input.
Move the cursor to the text column, the text is shown as blue, input button pops up on the right.
Click that button to switch between numeral input and English input (capitalized and small), Use
> or < to shift between small character and capitalized character.
2.6.2 Front Panel
Move the cursor to the text column. Click Fn key and use direction keys to select number you
wanted. Please click enter button to input.
42
Page 53
pp
(
y
3 Installation and Connections
Note: All the installation and operations here should conform to your local electric safety rules.
3.1 Check Unpacked DVR
When you receive the DVR from the forwarding agent, please check whether there is any visible
damage. The protective materials used for the package of the DVR can protect most accidental
clashes during transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list on the warranty card (Remote control is
optional). Finally you can remove the protective film of the DVR.
Note
Remote control is not a standard accessory and it is not included in the accessory bag.
3.2 About Front Panel and Real Panel
The model label in the front panel is very important; please check according to your purchase
order.
The label in the rear panel is very important too. Usually we need you to represent the serial
number when we provide the service after sales.
3.3 HDD Installation
You can refer to the Appendix for recommended HDD brand.
Please follow the instructions below to install hard disk.
3.3.1 1U series
This series DVR has two SATA HDDs. Please use HDD of 7200rpm or higher.
1. Loosen the screws of the
u
er cover and side panel.
2. Fix four screws in the HDD
Turn just three rounds).
3. Place the HDD in accordance with the four holes in the bottom.
4. Turn the device upside down
and then turn the screws in
firml
.
5. Fix the HDD firmly.
6. Connect the HDD cable and
power cable.
43
Page 54
pp
pp
7. Put the cover in accordance
with the clip and then place the
upper cover back.
8. Secure the screws in the
rear panel and the side panel.
3.3.2 1.5U series
This series DVR has four SATA HDDs. Please use HDD of 7200rpm or higher.
1. Loosen the screws of the
u
er cover.
2. Line up the HDD to the four
holes of the HDD bracket.
3. Use four screws to fix HDD.
4. Unfasten the HDD power
cable.
5. Use the special data cable to
connect the HDD and the SATA port
6. Insert the HDD power cable.
Close the chassis and fix the
screws to secure firmly.
3.3.3 2U series (HD-SDI series, 960H )
This series DVR max supports 8 SATA HDDs. Please use HDD of 7200rpm or higher.
1. Loosen the screws of the
u
er cover.
2. Remove the HDD upper
bracket
3. Now you can see the bottom bracket
44
Page 55
4. Line up the HDD to the
four holes of the HDD
bracket.
7. Unfasten the HDD power
cable.
Important:
If the HDD amount is less than four, you do not need to install the HDD bracket.
When there is a bracket, please make sure the installation direction of HDDs is the same.
5. Use screws to fix HDD.
8. Insert the HDD power
cable.
6. Install the upper bracket and then
Use screws to fix HDD in the
bracket.
9. Use the special data cable to
connect the HDD and the SATA
port. Close the chassis and fix
the screws to secure firmly.
3.4 Rack Installation
Please note this installation mode is for 1.5U/2U series product.
Please follow the steps listed below.
z Use twelve screws to fix the unit z Please make sure the indoor temperature is below 35 (95°f).
z Please make sure there is 15cm (6 inches) space around the device to guarantee sound
ventilation.
z Please install from the bottom to the top.
z If there are more accessories connected in the rack, please take precaution measures in
case the rack power is overload.
3.5 Connecting Power Supply
Please check input voltage and device power button match or not.
We recommend you use UPS to guarantee steady operation, DVR life span, and other peripheral
equipments operation such as cameras.
3.6 Connecting Video Input and Output Devices
45
Page 56
3.6.1 Connecting Video Input
The video input interface is BNC. The input video format includes: PAL/NTSC BNC1.0VB
B75Ω.
HD-S series: BNC(0.8V
;
75
P-P
The video signal should comply with your national standards.
The input video signal shall have high SNR, low distortion; low interference, natural color and
suitable lightness.
Guarantee the stability and reliability of the camera signal:
The camera shall be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
The camera and the DVR should have the same grounding to ensure the normal operation of the
camera.
Guarantee stability and reliability of the transmission line
BTTTB
Please use high quality, sound shielded BNC. Please select suitable BNC model according to the
transmission distance.
If the distance is too long, you should use twisted pair cable, and you can add video
compensation devices or use optical fiber to ensure video quality.
You should keep the video signal away from the strong electromagnetic interference, especially
the high tension current.
Keep connection lugs in well contact
BTTTB
The signal line and shielded wire should be fixed firmly and in well connection. Avoid dry joint,
lap welding and oxidation.
BTTTB
P- P ,
3.6.2 Connecting Video Output
Video output includes a BNC(PAL/NTSC1.0V
System supports BNC, VGA and HDMI output at the same time.
When you are using pc-type monitor to replace the monitor, please pay attention to the following
points:
z To defer aging, do not allow the pc monitor to run for a long time.
z Regular demagnetization will keep device maintain proper status.
z Keep it away from strong electromagnetic interference devices.
Using TV as video output device is not a reliable substitution method. You also need to reduce
the working hour and control the interference from power supply and other devices. The low
quality TV may result in device damage.
75output ,a VGA output and HDMI output.
P-P
3.7 Connecting Audio Input & Output, Bidirectional Audio
3.7.1 Audio Input
These series products audio input port adopt BNC port.
Due to high impedance of audio input, please use active sound pick-up.
Audio transmission is similar to video transmission. Try to avoid interference, dry joint, loose
contact and it shall be away from high tension current.
3.7.2 Audio Output
The audio output signal parameter is usually over 200mv 1K (BNC). It can directly connect to
low impedance earphone, active sound box or amplifier-drive audio output device.
46
Page 57
If the sound box and the pick-up cannot be separated spatially, it is easy to arouse squeaking. In
this case you can adopt the following measures:
z Use better sound pick-up with better directing property.
z Reduce the volume of the sound box.
z Using more sound-absorbing materials in decoration can reduce voice echo and improve
acoustics environment.
z Adjust the layout to reduce happening of the squeaking.
3.8 Alarm Input and Output Connection
Please refer to the following sheet for alarm input and output connection.
There are two alarm input types for you to select: normal open (NO) and normal close (NC).
1. Alarm input
a. Please make sure alarm input mode is grounding alarm input.
b. Grounding signal is needed for alarm input.
c. Alarm input needs the low level voltage signal.
d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)
e. When you are connecting two DVRs or you are connecting one DVR and one other device,
please use a relay to separate them,
2. Alarm output
The alarm output port should not be connected to high power load directly (It shall be less than
1A) to avoid high current which may result in relay damage. Please use the co contactor to
realize the connection between the alarm output port and the load.
3. How to connect PTZ decoder
a. Ensure the decoder has the same grounding with DVR, otherwise you may not control the PTZ.
Shielded twisted wire is recommended and the shielded layer is used to connect to the grounding.
b. Avoid high voltage. Ensure proper wiring and some thunder protection measures. c. For too long signal wires, 120 should be parallel connected between A, B lines on the far end
to reduce reflection and guarantee the signal quality.
d. “485 A, B” of DVR cannot parallel connect with “485 port” of other device.
e. The voltage between of A,B lines of the decoder should be less than 5v.
4. Please make sure the front-end device has soundly earthed.
Improper grounding may result in chip damage.
3.8.1 Alarm Input and Output Details
You can refer to the following sheet X for alarm input and output information.
Important
Please refer to the specifications for the alarm input and output channel amount. Do not
merely count the alarm input and out channel amount according to the ports on the rear
panel.
3.8.1.1 1U Series
The 4/8-channel series product interface is shown as below. See Figure 3-1.
47
Page 58
AB cable
connection
Figure 3-1
Please refer to the following sheet and Figure 3-1 for detailed information.
In the second line, from the left to the right,: 1,2,3,4,
5678. In the first line, from
the left to the right: 1-NO C2-NO C 3-NO C
485 A/B 485 communication port. They are used to control devices such as
The 16-channel interface is shown as in Figure 3-2.
ALARM 1 to ALARM 8. The alarm becomes active in low voltage.
There are three groups of normal open activation output (on/off button)
Earth cable.
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
AB cable
connection
Figure 3-2
Please refer to the following sheet and Figure 3-2 for detailed information.
In the second line, from the left to the right,: 1,2,3,4,
5678.and the first line from the left to the right : 9,10, 11121314 1516 In the first line, from the left to the right: 3-NO Cand the second line from the left to the right 1­NO C2-NO C.
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
There are three groups of normal open activation output (on/off button)
Earth cable.
48
Page 59
485 A/B 485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
3.8.1.2 1.5U Series (Simple 1.5U)
The 1.5U series product interface is shown as in Figure 3-3.
Figure 3-3
You can refer to the following sheet and Figure 3-3 for alarm input and output information.
In the first line, from the left to the right,: 12345
678910 11121314 1516 In the second line,
from the left to the right: NO1 C1
NO2 C2 NO3 C3 NO4 C4,
NO5 C5 NC5 CTRL 12V Control power output. You need to close the device power to cancel
+12V It is external power input. Need the peripheral equipment to provide
485 A/B 485 communication port. They are used to control devices such as
3.8.1.3 2U Series
The 2U series product interface is shown as in
Figure
3-4.
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
The first four are four groups of normal open activation output (on/off button) NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
the alarm.
+12V power (below 1A).
Earth cable.
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
AB cable
connection
You can refer to the following sheet and
Figure 3-4
AB cable
connection
49
Page 60
Figure 3-4 for alarm input and output information.
In the first line, from the left to the right,: 12345
678910 11121314 1516 In the first line after
the number 1-16, from the left to the right: NO1 C1
NO2 C2 NO3 C3 NO4 C4,
NO5 C5 NC5 CTRL 12V Control power output. You need to close the device power to cancel
+12V It is external power input. Need the peripheral equipment to provide
485 A/B 485 communication port. They are used to control devices such as
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
The first four are four groups of normal open activation output (on/off button) NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
the alarm.
+12V power (below 1A).
Earth cable.
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
2U Series (HD-SDI series)
In the first line, from the left to the right,: 1234
In the first line after the number 1-4, from the left to the right: NO1 C1
NO2 C2 NO3 C3 NO4 C4,
NO5 C5 NC5
T+, T-, R+, R-
485 A/B 485 communication port. They are used to control devices such as
ALARM 1 to ALARM 4. The alarm becomes active in low voltage.
The first four are four groups of normal open activation output (on/off button) NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
Earth cable.
RS485 port
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
2U Series (960H series)
50
Page 61
In the first line, from the left to the right,: 1234,, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 In the first line after the number 1-4, from the left to the right: NO1 C1
NO2 C2 NO3 C3 NO4 C4,
NO5 C5 NC5
CTRL 12V Control power output. You need to close the device power to cancel
+12V It is external power input. Need the peripheral equipment to provide
T+, T-, R+, R- RS485 port
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
The first four are four groups of normal open activation output (on/off button) NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
the alarm.
+12V power (below 1A). Earth cable.
485 A/B 485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120T between A/B cables if there are too many PTZ decoders.
3.8.2 Alarm Input Port
Please refer to the following sheet for more information.
z Normal open or Normal close type.
z Please parallel connect COM end and GND end of the alarm detector (Provide external
power to the alarm detector).
z Please parallel connect the Ground of the DVR and the ground of the alarm detector.
z Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)
z Use the same ground with that of DVR if you use external power to the alarm device.
Figure 3-5
51
Page 62
3.8.3 Alarm Output Port
z Provide power to peripheral alarm device.
z To avoid overloading, please read the following relay parameters sheet carefully.
z RS485 A/B cable is for the A/B cable of the PTZ decoder.
Relay Specification
Model:
Material of the touch
Rating Resistance Load
Insulation
Surge voltage
Length of open time
Length of close time
Longevity
Temperature
JRC-27F
Silver
Rated switch capacity 30VDC 2A, 125VAC 1A
Maximum switch power 125VA 160W
Maximum switch voltage 250VAC, 220VDC
Maximum switch currency 1A Between touches with same
polarity
Between touches with different polarity
Between touch and winding 1000VAC 1minute Between touches with same
polarity 3ms max
3ms max
Mechanical 50×106 times (3Hz)
Electrical 200×103 times (0.5Hz)
-40 ~+70
1000VAC 1minute
1000VAC 1minute
1500V (10×160us)
3.9 RS232
You can connect the DVR with POS or Keyboard through RS232.
With POS system, the DVR can communicate through RS232 and network. For the POS system, the
DVR can integrate the text content and even search the record through the info.
The series DVR also support NKB operation. You can operate the DVR from the keyboard controls
instead of using the control pad on the front panel of the unit.
To connect a NKB keyboard to the DVR:
1. Assemble the KBD keyboard according to the instructions in its accompanying installation manual.
2. Connect the KBD keyboard into one of the RS232 ports on the DVR or through network.
3.10 RS485
When the DVR receives a camera control command, it transmits that command up the coaxial cable
to the PTZ device. RS485 is a single-direction protocol; the PTZ device can’t return any data to the
unit. To enable the operation, connect the PTZ device to the RS485 (A,B) input on the DVR. See
X289H289H289HFigure 3-8X.
Since RS485 is disabled by default for each camera, you must enable the PTZ settings first. This
series DVRs support multiple protocols such as Pelco-D, Pelco-P.
To connect PTZ devices to the DVR:
52
Page 63
1. Connect RS485 A,B on the DVR rear panel.
2. Connect the other end of the cable to the proper pins in the connector on the camera.
3. Please follow the instructions to configure a camera to enable each PTZ device on the DVR.
3.11 Other Interfaces
There are still other interfaces on the DVR, such as USB ports. You can refer to the Figure 3-6 for
more information.
1U series
53
Page 64
1.5U Series
2U Series
Figure 3-6
54
Page 65
4 Overview of Navigation and Controls
Note:
All the operations listed below are based on the 2U series product.
Before operation, please make sure:
z You have properly installed HDD and all the cable connections.
z The provided input power and the device power are matched.
z The external power shall be DC 12V.
z Always use the stable current, if necessary UPS is a best alternative measure.
4.1 Login, Logout & Main Menu
4.1.1 Login
After system booted up, system pops up the startup wizard.
Click the Cancel button; you can go to the system login interface.
Click the Next Step button; you can go to the startup wizard interface. Here you can set the
system basic information. See Figure 4-1.
Figure 4-1
The system login interface is shown as in Figure 4-2.
System consists of four accounts:
z Username: admin. Password: admin. (administrator, local and network)
z Username: 888888. Password: 888888. (administrator, local only)
z Username: 666666. Passwords: 666666(Lower authority user who can only monitor, playback,
backup and etc.)
z Username: default. Password: default(hidden user)
You can use USB mouse, front panel, remote control or keyboard to input. About input method:
Click
Note:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and five times login failure
will result in account lock!
to switch between numeral, English character (small/capitalized) and denotation.
55
Page 66
Figure 4-2
4.1.2 Main Menu
After you logged in, the system main menu is shown as below. See Figure 4-3.
There are total six icons: search, information, setting, backup, advanced and shutdown.
You can move the cursor to highlight the icon, and then double click mouse to enter the sub-
menu.
Figure 4-3
4.1.3 Logout
There are two ways for you to log out.
One is from menu option:
In the main menu, click shutdown button, you can see an interface is shown as below. See
Figure 4-4.
Figure 4-4
There are several options for you. See Figure 4-5.
Figure 4-5
56
Page 67
The other ways is to press power button on the front panel for at least 3 seconds, system will
stop all operations. Then you can click the power button in the rear panel to turn off the DVR.
4.1.4 Auto Resume after Power Failure
The system can automatically backup video and resume previous working status after power
failure.
4.1.5 Replace Button Battery
Please make sure to use the same battery model if possible.
We recommend replace battery regularly (such as one-year) to guarantee system time
accuracy.
Note:
Before replacement, please save the system setup, otherwise, you may lose the data
completely!
4.2 Manual Record
4.2.1 Live Viewing
After you logged in, the system is in live viewing mode. You can see system date, time and
channel name. If you want to change system date and time, you can refer to general settings
(Main Menu->Setting->General). If you want to modify the channel name, please refer to the
display settings (Main Menu->Setting->Display)
1
2
Preview Zoom Function
Move your mouse to the left top corner of the preview interface; you can see the preview
zoom button. See Figure 4-6. Left click the icon; you can see a hook icon. Now you have
enabled the preview zoom function. You can drag the mouse to zoom in the image.
Preview
zoom button
Recording status
Motion detection
3
4
Video loss
Camera lock
Figure 4-6
4.2.2 Manual record Note:
You need to have proper rights to implement the following operations. Please make sure the
HDD has been properly installed.
4.2.2.1 Manual record menu
57
Page 68
There are two ways for you to go to manual record menu.
z Right click mouse or in the main menu, Advanced->Manual Record.
z In live viewing mode, click record button in the front panel or record button in the remote
control.
Manual record menu is shown as in Figure 4-7.
4.2.2.2 Basic operation
There are three statuses: schedule/manual/stop. Please highlight icon“○” to select
corresponding channel.
z Manual: The highest priority. After manual setup, all selected channels will begin ordinary
recording.
z Schedule: Channel records as you have set in recording setup (Main Menu->Setting-
>Schedule)
z Stop: All channels stop recording.
Figure 4-7
4.2.2.3 Enable/disable record
Please check current channel status: “” means it is not in recording status, “” means it is in
recording status.
You can use mouse or direction key to highlight channel number. See Figure 4-8.
Figure 4-8
4.2.2.4 Enable all channel recording
Highlight below All, you can enable all channel recording.
z All channel schedule record
Please highlight “ALL” after “Schedule”. See Figure 4-9.
When system is in schedule recording, all channels will record as you have previously set
(Main menu->Setting->Schedule).
The corresponding indication light in front panel will turn on.
58
Page 69
Figure 4-9
z All channel manual record
Please highlight “ALL” after “Manual.” See Figure 4-10.
When system is in manual recording, all scheduled set up you have set in will be null ((Main
menu->Setting->Schedule)).
You can see indication light in front panel turns on, system begins manual record now.
Figure 4-10
4.2.2.5 Stop all channel recording
Please highlight “ALL” after “Stop”. See Figure 4-11.
System stops all channel recording no matter what mode you have set in the menu (Main
menu->Setting->Schedule)
Figure 4-11
4.3 Search & Playback
Click search button in the main menu, search interface is shown as below. See Figure 4-12.
Usually there are three file types:
z R: Regular recording file.
z A: External alarm recording file.
z M: Motion detection recording file
59
Page 70
2
1
11
7 8
12 9
Figure 4-12
3
4
56 10
Please refer to the following sheet for more information.
SN Name Function
1
2
3 Calendar
4
Display window
Search type
Playback mode and channel selection pane.
zHere is to display the searched picture or file. zSupport 1/4/9/16-window playback.
zHere you can select to search the picture or the recorded
file. zWhen there is displayed picture on the left pane, you can set the corresponding setup
zThe blue highlighted date means there is picture or file. Otherwise, there is no
picture or file.
zIn any play mode, click the date you want to see, you can see the corresponding
record file trace in the time bar.
zPlayback mode1/4/9/16. (It may vary due to different series.) In 1-window playback mode: you can select 1-16 channels. In 4-window playback mode: you can select 4 channels according to your
requirement.
In 9-window playback mode, you can switch between 1-9 and 10-16 channels. In 16-window playback mode, you can switch between1-16 and 17-32
channels. zThe time bar will change once you modify the playback mode or the channel option.
60
Page 71
zDouble click it, you can view the picture/record file list of current day. zThe file list is to display the first channel of the record file. zThe system can display max 128 files in one time. Use the S/T or the mouse to
view the file. Select one item, and then double click the mouse or click the ENTER button to playback.
zYou can input the period in the following interface to begin accurate search. zFile typeR—regular record A—external alarm recordM—Motion detect
record.
5
File list switch button
6
7
Card number search
Playback control pane.
The card number search interface is shown as below.
Play/Pause There are three ways for you to begin playback.
/
Stop
W
W/ X
Note: The actual play speed has relationship with the software version.
z The play button z Double click the valid period of the time bar. z Double click the item in the file list.
In slow play mode, click it to switch between play/pause.
Backward play In normal play mode, left click the button, the file begins backward play. Click it again to pause current play. In backward play mode, click ►/ to restore normal play. In playback mode, click it to play the next or the previous section. You can click continuously when you are watching the files from the same channel. In normal play mode, when you pause current play, you can click W and X to begin frame by frame playback. In frame by frame playback mode, click ►/ to restore normal playback.
Slow play In playback mode, click it to realize various slow play modes such as slow play 1, slow play 2, and etc.
Fast forward In playback mode, click to realize various fast play modes such as fast play 1,fast play 2 and etc.
Smart search
The volume of the playback
Click the snapshot button in the full-screen mode, the system can snapshot 1 picture per second.
zIt is to display the record type and its period in current search criteria.
zIn 4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
zUse the mouse to click one point of the color zone in the time bar, system begins
8 Time bar
9 Time bar ●The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger the
playback. zThe time bar is beginning with 0 o'clock when you are setting the configuration. The time bar zooms in the period of the current playback time when you are playing the file.
zThe green color stands for the regular record file. The red color stands for the
external alarm record file. The yellow stands for the motion detect record file.
61
Page 72
unit zoom rate. You can accurately set the time in the time bar to playback the record.
zThe time bar is beginning with 0 o'clock when you are setting the configuration. The time bar zooms in the period of the current playback time when you are
playing the file. Select the file(s) you want to backup from the file list. System max supports files from four channels. Then click the backup button, now you can see the backup
10 Backup
11 Clip
12
13
Record type
Smart search
menu. Click the start button to begin the backup operation. Check the file again you can cancel current selection. System max supports to display 32 files from one channel. zIt is to edit the file.
Please play the file you want to edit and then click this button when you want to edit. You can see the corresponding slide bar in the time bar of the corresponding channel. You can adjust the slide bar or input the accurate time to set the file end time. Click this button again and then save current contents in a new file. .
In any play mode, the time bar will change once you modify the search type.
z When system is playing, you can select a zone in the window to begin motion
detect. Click the motion detect button to begin play.
z Current button is null once the motion detect play has begun. z The system will take the whole play zone as the motion detect region by
default.
z The motion detect play stopped once you switch the play file. z Operations such as set time bar, click the play button, or any file list operation
will stop current motion detect play.
Other Functions
Other channel
14
15 Digital zoom
Note:
All the operations here (such as playback speed, channel, time and progress) have
relationship with hardware version. Some series DVRs do not support some functions or
playback speeds.
synchronization switch to play when playback
When playing the file, click the number button, system can switch to the same period of the corresponding channel to play. When the system is in full-screen playback mode, left click the mouse in the screen. Drag your mouse in the screen to select a section and then left click mouse to realize digital zoom. You can right click mouse to exit.
4.4 Schedule
After system booted up, it is in default 24-hour regular mode. You can set record type and
time in schedule interface.
4.4.1 Schedule Menu
In the main menu, from setting to schedule, you can go to schedule menu. See Figure 4-13.
z Channel: Please select the channel number first. You can select “all if you want to set for
the whole channels.
z Week day: There are eight options: ranges from Saturday to Sunday and all.
z Pre-record: System can pre-record the video before the event occurs into the file. The value
ranges from 1 to 30 seconds depending on the bit stream.
z Redundancy: System supports redundancy backup function. It allows you backup recorded
file in two disks. You can highlight Redundancy button to activate this function. Please note,
before enable this function, please set at least one HDD as redundant. (Main menu-
>Advanced->HDD Management) Please refer to chapter 4.4.1.2 for detailed information.
62
Page 73
z Snapshot: You can enable this function to snapshoot image when alarm occurs.
z Record types: There are four types: regular, motion detection (MD), Alarm, MD & alarm.
Please highlight icon to select the corresponding function. After completing all the setups
please click save button, system goes back to the previous menu.
At the bottom of the menu, there are color bars for your reference. Green color stands for
regular recording, yellow color stands for motion detection and red color stands for alarm
recording. The white means the MD and alarm record is valid. Once you have set to record
when the MD and alarm occurs, system will not record neither motion detect occurs nor the
alarm occurs.
Figure 4-13
4.4.1.1 Quick Setup
This function allows you to copy one channel setup to another. After setting in channel 1, you can
click paste button and turn to channel 2 and then click copy button. You can finish setting for one
channel and then click save button or you can finish all setup and then click save button to
memorize all the settings.
4.4.1.2 Redundancy
Redundancy function allows you to memorize record file in several disks. When there is file
damage occurred in one disk, there is a spare one in the other disk. You can use this
function to maintain data reliability and safety.
In the main menu, from Setting to Schedule, you can highlight redundancy button to enable
this function. See Figure 4-13.
In the main menu, from Advanced to HDD management, you can set one or more disk(s) as
redundant. You can select from the dropdown list. See Figure 4-14. System auto overwrites
old files once hard disk is full.
Please note only read/write disk or read-only disk can backup file and support file search
function, so you need to set at least one read-write disk otherwise you can not record video.
Note
About redundancy setup:
z If current channel is not recording, current setup gets activated when the channel begin
recording the next time.
z If current channel is recording now, current setup will get activated right away, the current file
will be packet and form a file, then system begins recording as you have just set.
63
Page 74
After all the setups please click save button, system goes back to the previous menu.
Figure 4-14
Playback or search in the redundant disk.
There are two ways for you to playback or search in the redundant disk.
z Set redundant disk(s) as read-only disk or read-write disk (Main menu->Advanced->HDD
management). See Figure 4-14.System needs to reboot to get setup activated. Now you can
search or playback file in redundant disk.
z Dismantle the disk and play it in another PC.
4.4.2 Snapshot
4.4.2.1 Schedule Snapshot
In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency.
Note: for 960H series, “960H” is added to “image size” In General interface please input upload interval.
In Schedule interface, please enable snapshot function.
Please refer to the following figure for detailed information. See Figure 4-15
64
Page 75
Figure 4-15
4.4.2.2 Activation Snapshot
Please follow the steps listed below to enable the activation snapshot function. After you
enabled this function, system can snapshot when the corresponding alarm occurred.
z In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency.
z In General interface please input upload interval.
z In Detect interface please enable snapshot function for specified channels. Or in alarm
interface please enable snapshot function for specified channels.
Please refer to the following figure for detailed information. See Figure 4-16.
4.4.2.3 Priority
Figure 4-16
65
Page 76
Please note the activation snapshot has the higher priority than schedule snapshot. If you
have enabled these two types at the same time, system can activate the activation snapshot
when alarm occurs, and otherwise system just operates the schedule snapshot.
4.4.3 Image FTP
In Network interface, you can set FTP server information. Please enable FTP function and
then click save button. See Figure 4-17.
Please boot up corresponding FTP server.
Please enable schedule snapshot (Chapter 4.4.2.1) or activation snapshot (Chapter 4.4.2.2)
first, now system can upload the image file to the FTP server.
Please input the
corresponding information
here, if you just upload the
image FTP.
Figure 4-17
4.4.4 Snapshot Disk (For special series only)
Set one disk as snapshot (Main menu->Advanced->HDD management) and then click execute
button. See Figure 4-18. System needs to reboot to get current setup activated.
Figure 4-18
All scheduled snapshot files or activated snapshot files will be memorized in the snapshot
disk.
You can search the corresponding images via Web. See Figure 4-19.
66
Page 77
Select search
engine here
You can see result here. Double click
file name, you can view the image
content.
Select a file and then
click here to view
image content.
There are max 100 files in one
page. Click here to view more.
Figure 4-19
4.5 Detect
4.5.1 Go to Detect Menu
In the main menu, from Setting to Detect, you can see motion detect interface. See Figure
4-20.There is three detection types: motion detection, video loss, camera masking.
4.5.2 Motion Detect
Detection menu is shown as below. See Figure 4-20
z Event type: from the dropdown list you can select motion detection type.
z Channel: select the channel to activate recording function once alarm occurred. Please make
sure you have set MD record in encode interface(Main Menu->Setting->Schedule) and
schedule record in manual record interface(Main Menu->Advanced->Manual Record)
z Latch: when motion detection complete, system auto delays detecting for a specified time.
The value ranges from 10-300(Unit: second)
z Region: Click select button, the interface is shown as in Figure 4-21. Here you can set
motion detection zone. There are 396(PAL)/330(NTSC) small zones. The green zone is
current cursor position. Grey zone is the motion detection zone. Black zone is the disarmed
zone. You can click Fn button to switch between the arm mode and disarm mode. In arm
mode, you can click the direction buttons to move the green rectangle to set the motion
detection zone. After you completed the setup, please click ENTER button to exit current
setup. Do remember click save button to save current setup. If you click ESC button to exit
the region setup interface system will not save your zone setup.
z Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
67
Page 78
z Show message: System can pop up a message to alarm you in the local host screen if you
enabled this function.
z Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z Send email: System can send out email to alert you when alarm occurs.
z PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset,
tour &pattern when there is an alarm. Click “select” button, you can see an interface is
shown as in
X305H305H305HFigure 4-22X.
z Period: Click set button, you can see an interface is shown as in Figure 4-23. Here you can
set for business day and non-business day. In Figure 4-23 click set button, you can see an
interface is shown as in Figure 4-24. Here you can set your own setup for business day and
non-business day.
z Anti-dither: Here you can set anti-dither time.
z Alarm output: when alarm occurred, system enables peripheral alarm devices.
z Tour: Here you can enable tour function when alarm occurs. System one-window tour.
Please go to chapter 5.3.9 Display for tour interval setup.
z Snapshot: You can enable this function to snapshoot image when alarm occurs.
Please highlight icon to select the corresponding function. After all the setups please click
save button, system goes back to the previous menu.
Note:
In motion detection mode, you can not use copy/paste to set channel setup since the video in
each channel may not be the same.
In Figure 4-21, you can left click mouse and then drag it to set a region for motion detection.
Click Fn to switch between arm/withdraw motion detection. After setting, click enter button to exit.
Figure 4-20
68
Page 79
Figure 4-21
Figure 4-22
Figure 4-23
4.5.3 Video Loss
Figure 4-24
69
Page 80
In Figure 4-20, select video loss from the type list. You can see the interface is shown as in
Figure 4-25.This function allows you to be informed when video loss phenomenon occurred.
You can enable alarm output channel and then enable show message function.
Tips:
You can enable preset activation operation when video loss occurs.
Please refer to chapter 4.5.2 motion detection for detailed information.
Figure 4-25
4.5.4 Camera Masking
When someone viciously masks the lens, or the output video is in one-color due to the
environments light change, the system can alert you to guarantee video continuity. Camera
masking interface is shown as in Figure 4-26.
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
Please refer to chapter 4.5.2 motion detection for detailed information.
Note:
In Detect interface, copy/paste function is only valid for the same type, which means you can
not copy a channel setup in video loss mode to camera masking mode.
Figure 4-26
70
Page 81
4.6 Alarm Setup and Alarm Activation
Before operation, please make sure you have properly connected alarm devices such as
buzzer.
4.6.1 Go to alarm setup interface
In the main menu, from Setting to Alarm, you can see alarm setup interface. See Figure 4-27.
4.6.2 Alarm setup
Alarm interface is shown as below. See Figure 4-27.
z Alarm in: Here is for you to select channel number.
z Event type: There are two types. One is local input and the other is network input.
z Type: normal open or normal close.
z PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset,
tour& pattern when there is an alarm. Click “select” button, you can see an interface is
shown as in Figure 4-28.
z Period: Click set button, you can see an interface is shown as in Figure 4-29. Here you can
set for business day and non-business day. In Figure 4-29, click set button, you can see an
interface is shown as in Figure 4-30. Here you can set your own setup for business day and
non-business day.
z Anti-dither: Here you can set anti-dither time.
z Show message: System can pop up a message to alarm you in the local host screen if you
enabled this function.
z Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z Send email: System can send out email to alert you when alarm occurs.
z Record channel: you can select proper channel to record alarm video (Multiple choices). At
the same time you need to set alarm record in schedule interface (Main Menu->Setting-
>Schedule) and select schedule record in manual record interface (Main Menu->Advance-
>Manual Record).
z Latch: Here is for you to set proper delay duration. Value ranges from 10 to 300 seconds.
System automatically delays specified seconds in turning off alarm and activated output after
external alarm cancelled.
z Tour: Here you can enable tour function when alarm occurs. System supports one-window
tour. Please go to chapter 5.3.9 Display for tour interval setup.
z Buzzer: Highlight the icon to enable this function. The buzzer beeps when alarm occurs.
For snapshot operation, please refer to chapter 4.4.2.
Please highlight icon
please click save button, system goes back to the previous menu.
to select the corresponding function. After setting all the setups
71
Page 82
Figure 4-27
Figure 4-28
Figure 4-29
Figure 4-30
72
Page 83
4.7 Backup
DVR support USB device backup and network download. Here we introduce USB backup.
You can refer to Chapter 7 Web Client Operation for network download backup operation.
4.7.1 Detect Device
Click backup button, you can see an interface is shown as in Figure 4-31. Here is for you to
view devices information.
You can view backup device name and its total space and free space. The device includes
USB burner, flash disk, SD card, and portable HDD.
Figure 4-31
4.7.1 Backup
Select backup device and then set channel, file start time and end time.
Click add button, system begins search. All matched files are listed below. System
automatically calculates the capacity needed and remained. See Figure 4-32. system only backup files with a before channel name. You can use Fn or cancel button to delete after file serial number.
Click backup button, you can backup selected files. There is a process bar for you reference.
When the system completes backup, you can see a dialogue box prompting successful
backup.
Figure 4-32
73
Page 84
Click backup button, system begins burning. At the same time, the backup button becomes
stop button. You can view the remaining time and process bar at the left bottom.
z File format: Click the file format; you can see there are two options: DAV/ASF.
z Picture backup: Please set the corresponding time, channel and then select the type as
PIC from the dropdown list. See Figure 4-33. Please click the Add button and then select
the pictures. Click the Start button; you can copy the specified pictures to the selected
portable devices.
Figure 4-33
z One key backup: It includes three steps: the search, select all, start the backup. You can
skip the above three steps and then copy all the searched files directly.
The file name format usually is: SN_CH+channel number+time Y+M+D+H+M+S. In the file
name, the YDM format is the same as you set in general interface. (Main Menu ->Setting -
>General).File extension name is .dav.
Tips:
During backup process, you can click ESC to exit current interface for other operation. The
system will not terminate backup process.
Note:
When you click stop button during the burning process, the stop function becomes activated
immediately. For example, if there are ten files, when you click stop system just backup five
files, system only save the previous 5 files in the device (But you can view ten file names).
4.8 PTZ Control and Color Setup
Note: All the operations here are based on PELCOD protocol. For other protocols, there
might be a little difference.
4.8.1 Cable Connection
Please follow the procedures below to go on cable connection
z Connect the dome RS485 port to DVR 485 port.
z Connect dome video output cable to DVR video input port.
z Connect power adapter to the dome.
4.8.2 PTZ Setup
Note: The camera video should be in the current screen. Before setup, please check the
following connections are right:
z PTZ and decoder connection is right. Decoder address setup is right.
z Decoder A (B) line connects with DVR A (B) line.
Boot up the DVR, input user name and password.
In the main menu, click setting, and then click Pan/Tilt Control button. The interface is shown
as in Figure 4-34. Here you can set the following items:
74
Page 85
z Channel: select the current camera channel.
z Protocol: select corresponding PTZ protocol(such as PELCOD)
z Address: default address is 1.
z Baud rate: select corresponding baud rate. Default value is 9600.
z Data bits: select corresponding data bits. Default value is 8.
z Stop bits: select corresponding stop bits. Default value is 1.
z Parity: there are three options: odd/even/none. Default setup is none.
Figure 4-34
After completing all the setting please click save button.
In one window display mode, right click mouse (click “Fn” Button in the front panel or click
“Fn” key in the remote control). The interface is shown as in Figure 4-35.
Figure 4-35
Click Pan/Tilt/Zoom, the interface is shown as below. See Figure 4-36.
Here you can set the following items:
z Step: value ranges fro 1 to 8.
z Zoom
z Focus
z Iris
Please click icon
and to adjust zoom, focus and iris.
75
Page 86
Figure 4-36
In Figure 4-36, please click direction arrows (See Figure 4-37) to adjust PTZ position. There are
total 8 direction arrows.
Figure 4-37
4.8.3 3D Intelligent Positioning Key
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. SeeFigure
4-38.
X Please make sure your protocol supports this function and you need to use mouse to
control.
Click this key, system goes back to the single screen mode. Drag the mouse in the screen to
adjust section size. The dragged zone supports 4X to 16X speeds. It can realize PTZ
automatically. The smaller zone you dragged, the higher the speed.
Figure 4-38
Here is a sheet for you reference.
Name Function
key Zoom Focus Iris
function Shortcut
key Near Near close
_
W
Function key
function Shortcut
Key Far Far Open
f
4.9 Preset/ Patrol/Pattern/Scan
In Figure 4-36, please click the “set” button. The interface is shown as below. See Figure 4-39.
Here you can set the following items:
z Preset
z Tour
z Pattern
z Border
76
Page 87
Figure 4-39
In X328H328H328H Figure 4-36, click page switch button, the interface is shown as in Figure 4-40.
Here you can activate the following functions:
z Preset
z Tour
z Pattern
z Auto scan
z Auto pan
z Flip
z Reset
z Page switch
Figure 4-40
Note:
z Preset, tour and pattern all need the value to be the control parameter. You can define it as
you require.
z You need to refer to your speed dome user’s manual for Aux definition. In some cases, it
can be used for special process.
z The following setups are usually operated in the
X332H332H332HFigure 4-36, Figure 4-39 and Figure 4-40.
4.9.1Preset Setup
In Figure 4-36, use eight direction arrows to adjust camera to the proper position.
In Figure 4-39, click preset button and input preset number. The interface is shown as in Figure
4-41.
Now you can add this preset to one tour.
77
Page 88
Figure 4-41
4.9.2 Activate Preset
In Figure 4-40, please input preset number in the No. blank, and click preset button.
4.9.3 Patrol setup (Tour Setup)
In Figure 4-38, click patrol button. The interface is shown as in Figure 4-42.Input preset number
and add this preset to a patrol (tour). For each patrol (tour), you can input max 80 presets.
Figure 4-42
4.9.4 Activate Patrol (tour)
In X341H341H341H Figure 4-39, input patrol (tour) number in the No. blank and click patrol button
4.9.5 Pattern Setup
In Figure 4-39, click pattern button and then click “begin” button. The interface is shown as in
Figure 4-43. Then you can go to Figure 4-36 X to modify zoom, focus, and iris.
Go back to Figure 4-43 and click “end” button. You can memorize all these operations as pattern
1.
Figure 4-43
4.9.6 Activate Pattern Function
In X346H346H346H Figure 4-39, input mode value in the No. blank, and click pattern button.
78
Page 89
4.9.7 Auto Scan Setup
In X347H347H347H Figure 4-38, click border button. The interface is shown as in X348H348H348H Figure 4-43.
Please go to
Then please go to
X349H349H349H X349H349H349HFigure 4-35, use direction arrows to select camera left limit
X350H350H350H Figure 4-43X and click left limit button
Repeat the above procedures to set right limit.
Figure 4-44
4.9.8 Activate Auto Scan
In Figure 4-40, click “Auto Scan” button, the system begins auto scan. Correspondingly, the auto
scan button becomes Stop button. Click stop button to terminate scan operation.
4.10 Flip
In Figure 4-40, click page switch button, you can see an interface is shown as below. See Figure
4-45. Here you can set auxiliary function. The aux value has relation ship with the Aux button of
the decoder.
Click page switch button again, system goes back to Figure 4-36.
Figure 4-45
79
Page 90
5 Understanding of Menu Operations and Controls
5.1 Menu Tree
This series DVR menu tree is shown as below.
Backup
Information
HDD Info BPS Log Version Online Users
Setting General Encode
Schedule RS232
Menu Network
Alarm Detect Pan/ Tilt/Zoom Display
Default Search Advanced HDD Management
Alarm Output
Abnormity Manual Record Account Auto Maintain TV Adjust Video Matrix Title Overlay Config Backup
Shutdown
5.2 Main Menu
After you logged in, the system main menu is shown as below. See Figure 5-1.X There are total
six icons: search, Information, setting, backup, advanced and shutdown. Move the cursor to
highlight the icon, then double click mouse to enter the sub-menu.
80
Page 91
Figure 5-1
5.3 Setting
In main menu, highlight setting icon and double click mouse. System setting interface is shown
as below. See Figure 5-2.
Figure 5-2
5.3.1 General
General setting includes the following items. See X357H357H357HFigure 5-3X.
z System time: Here is for you to set system time
z Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or DD-MM-YYYY.
z Date separator: There are three denotations to separate date: dot, beeline and solidus.
z DST: Here you can set DST time and date. Please enable DST function and then click set
button. You can see an interface is shown as in Figure 5-4. Here you can set start time and
end time by setting corresponding week setup. In Figure 5-4, enable date button, you can
see an interface is shown as in Figure 5-5. Here you can set start time and end time by
setting corresponding date setup.
z Time format: There are two types: 24-hour mode or 12-hour mode.
z Language: System supports various languages: Chinese (simplified), Chinese (Traditional),
English, Italian, Japanese, French, Spanish (All languages listed here are optional. Slight
difference maybe found in various series.)
z HDD full: Here is for you to select working mode when hard disk is full. There are two options:
stop recording or rewrite. If current working HDD is overwritten or the current HDD is full
81
Page 92
while the next HDD is no empty, then system stops recording, If the current HDD is full and
then next HDD is not empty, then system overwrites the previous files.
z Pack duration: Here is for you to specify record duration. The value ranges from 60 to 120
minutes. Default value is 60 minutes.
z DVR No: When you are using one remote control (not included in the accessory bag) to
control several DVRs, you can give a name to each DVR for your management.
z Video standard: There are two formats: NTSC and PAL.
z Auto logout: Here is for you to set auto logout interval once login user remains inactive for a
specified time. Value ranges from 0 to 60 minutes.
z Startup wizard: Once you check the box here, system will go to the startup wizard directly
when the system restarts the next time. Otherwise, it will go to the login interface.
z Device ID: Please input a corresponding device name here.
Note:
Since system time is very important, do not modify time casually unless there is a must!
Before your time modification, please stop record operation first!
After completing all the setups please click save button, system goes back to the previous menu.
Figure 5-3
Figure 5-4
Figure 5-5
82
Page 93
5.3.2 Encode
Encode setting includes the following items. See Figure 5-6.
Please note some series do not support extra stream.
z Channel: Select the channel you want.
z Type: Please select from the dropdown list. There are three options: regular/motion
detect/alarm. You can set the various encode parameters for different record types.
z Compression: System supports H.264.
z Resolution: System supports various resolutions, you can select from the dropdown list. The
main stream supports D1/HD1/BCIF/CIF/QCIF and the extra stream supports CIF/QCIF.
Please note the option may vary due to different series.
Note:
a. for HD-SDI series, the main code-stream types are
1080P/720P/D1/HD/BCIF/CIF/QCIF; Extra code-stream resolution supports
1080P/720P/D1/HD/BCIF/CIF/QCIF.
b. for 960H series, the main code-stream types are 960H/D1/HD/BCIF/CIF/QCIF,; Extra
code-stream resolution supports 960H/D1/HD/BCIF/CIF/QCIF.
z Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in PAL mode.
z Bit rate type: System supports two types: CBR and VBR. In VBR mode, you can set video
quality.
z Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image
quality.
z Video/audio: You can enable or disable the video/audio.
z Overlay: Click overlay button, you can see an interface is shown in Figure 5-7.
Cover area (Privacy mask): Here is for you to set privacy mask section. You can drag you
mouse to set proper section size. In one channel video, system max supports 4 zones in one
channel.
Preview/monitor: privacy mask has two types. Preview and Monitor. Preview means the
privacy mask zone can not be viewed by user when system is in preview status. Monitor
means the privacy mask zone can not be view by the user when system is in monitor status.
Time display: You can select system displays time or not when you playback. Please click
set button and then drag the title to the corresponding position in the screen.
Channel display: You can select system displays channel number or not when you playback.
Please click set button and then drag the title to the corresponding position in the screen.
Please highlight icon
to select the corresponding function.
83
Page 94
Figure 5-6
Figure 5-7
5.3.3 Schedule
Please refer to chapter 4.4 schedule.
5.3.4 RS232
RS232 interface is shown as below. There are five items. See Figure 5-8.
z Function: There are various devices for you to select. Console is for you to use the COM or
mini-end software to upgrade or debug the program. The control keyboard is for you to
control the device via the special keyboard. Transparent COM (adapter) is to connect to the
PC to transfer data directly. Protocol COM is for card overlay function. Network keyboard is
for you to use the special keyboard to control the device. PTZ matrix is to connect to the
peripheral matrix control.
z Baud rate: You can select proper baud rate.
z Data bit: You can select proper data bit. The value ranges from 5 to 8.
z Stop bit: There are three values: 1/1.5/2.
z Parity: there are five choices: none/odd/even/space mark.
System default setup is:
z Function: Console
z Baud rate:115200
z Data bit:8
z Stop bit:1
z Parity: None
After completing all the setups please click save button, system goes back to the previous menu.
84
Page 95
Figure 5-8
5.3.5 Network
Here is for you to input network information.
z IP address: Here you can input IP address.
z Network Mode : Includes multiple access, fault tolerance, and load balancing
z Default Network Card: Please select eth0/eth1/bond0(optional) after enable multiple
access function
z Main Network Card: Please select eth0/eth1(optional).after enable multiple access
function.
Note: 960H series support the above three configurations and supports functions as multiple access, fault-tolerance and load balancing.
z DHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet
mask /Gateway. These values are from DHCP function. If you have not enabled DHCP
function, IP/Subnet mask/Gateway display as zero. You need to disable DHCP function to
view current IP information. Besides, when PPPoE is operating, you can not modify
IP/Subnet mask /Gateway.
z TCP port: Default value is 37777.
z UDP port: Default value is 37778.
z HTTP port: Default value is 80.
z RTSP port: Default value is 554.
z Max connection: system support maximal 20 users. 0 means there is no connection limit.
z Preferred DNS server: DNS server IP address.
z Alternate DNS server: DNS server alternate address.
z Transfer mode: Here you can select the priority between fluency/video qualities.
z LAN download: System can process the downloaded data first if you enable this function.
The download speed is 1.5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back to the previous menu.
85
Page 96
Figure 5-9
Figure 5-10
5.3.5.1 Advanced Setup
Advanced setup interface is shown as in Figure 5-11. Please draw a circle to enable
corresponding function and then double click current item to go to setup interface.
86
Page 97
Figure 5-11
5.3.5.2 IP Filter
IP filter interface is shown as in Figure 5-12. You can add IP in the following list. The list
supports max 64 IP addresses.
Please note after you enabled this function, only the IP listed below can access current DVR.
If you disable this function, all IP addresses can access current DVR.
Figure 5-12
5.3.5.3 NTP Setup
You need to install SNTP server (Such as Absolute Time Server) in your PC first. In Windows XP
OS, you can use command “net start w32time” to boot up NTP service.
NTP setup interface is shown as in Figure 5-13.
z Host IP: Input your PC address.
z Port: This series DVR supports TCP transmission only. Port default value is 123.
z Update interval: minimum value is 1. Max value is 65535. (Unit: minute)
z Time zone: select your corresponding time zone here.
Here is a sheet for your time zone setup.
City /Region Name Time Zone
London GMT+0 Berlin GMT+1 Cairo GMT+2 Moscow GMT+3 New Deli GMT+5 Bangkok GMT+7 Beijing (Hong Kong) GMT+8 Tokyo GMT+9 Sydney GMT+10 Hawaii GMT-10 Alaska GMT-9
Pacific Time(P.T) GMT-8 American Mountain Time(M.T) GMT-7 American Central Time(C.T) GMT-6
87
Page 98
American Eastern Time(E.T) GMT-5 Atlantic Time GMT-4 Brazil GMT-3 Middle Atlantic Time GMT-2
Figure 5-13
5.3.5.4 Multiple Cast Setup
Multiple-cast setup interface is shown as in Figure 5-14.
Figure 5-14
Here you can set a multiple cast group. Please refer to the following sheet for detailed
information.
z IP multiple cast group address
-224.0.0.0-239.255.255.255
-“D” address space
z The higher four-bit of the first byte=”1110”
z Reserved local multiple cast group address
-224.0.0.0-224.0.0.255
-TTL=1 When sending out telegraph
-For example
224.0.0.1 All systems in the sub-net
224.0.0.2 All routers in the sub-net
224.0.0.4 DVMRP router
224.0.0.5 OSPF router
224.0.0.13 PIMv2 router
z Administrative scoped addressees
-239.0.0.0-239.255.255.255
-Private address space
88
Page 99
z Like the single broadcast address of RFC1918
z Can not be used in Internet transmission
z Used for multiple cast broadcast in limited space.
Except the above mentioned addresses of special meaning, you can use other addresses. For
example:
Multiple cast IP: 235.8.8.36
Multiple cast PORT: 3666.
After you logged in the Web, the Web can automatically get multiple cast address and add it to
the multiple cast groups. You can enable real-time monitor function to view the view.
Please note multiple cast function applies to special series only.
5.3.5.5 PPPoE
PPPoE interface is shown as in Figure 5-15.
Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider).
Click save button, you need to restart to activate your configuration.
After rebooting, DVR will connect to internet automatically. The IP in the PPPoE is the DVR
dynamic value. You can access this IP to visit the unit.
Figure 5-15
5.3.5.6 DDNS Setup
DDNS setup interface is shown as in Figure 5-16.
You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In
other words, this PC is a DNS (domain name server).
In network DDNS, please select DDNS type and highlight enable item. Them please input your
PPPoE name you get from you IPS and server IP (PC with DDNS ) . Click save button and then
reboot system.
Click save button, system prompts for rebooting to get all setup activated.
After rebooting, open IE and input as below: http//(DDNS server IP)/(virtual directory name)/webtest.htm e.g.: http//10.6.2.85/DVR _DDNS/webtest.htm.)
Now you can open DDNSServer web search page.
89
Page 100
Figure 5-16
Please note NNDS type includes: CN99 DDNSNO-IP DDNSPrivate DDNSDyndns DDNS
and sysdns DDNS. All the DDNS can be valid at the same time, you can select as you
requirement.
Private DDNS function shall work with special DDNS server and special Professional
Surveillance Software (PSS).
5.3.5.7 UPNP
The UPNP protocol is to establish a mapping relationship between the LAN and the WAN.
Please input the router IP address in the LAN in Figure 5-10. Double click the UPNP item in
Figure 5-11, you can see the following interface. See Figure 5-17.
z UPNP on/off Turn on or off the UPNP function of the device.
z Status: When the UPNP is offline, it shows as “Unknown”. When the UPNP works it shows
“Success”
z Router LAN IP: It is the router IP in the LAN.
z WAN IP: It is the router IP in the WAN. z Port Mapping list The port mapping list here is the one to one relationship with the router’s
port mapping setting.
z Enable Switch
z List
Service nameDefined by user.
Protocol Protocol type
Internal portPort that has been mapped in the router.
External portPort that has been mapped locally.
z Default: UPNP default port setting is the HTTP, TCP and UDP of the DVR.
z Add to the list: Click it to add the mapping relationship.
z Delete: Click it to remove one mapping item.
Double click one item; you can change the corresponding mapping information. See Figure 5-18.
Important:
When you are setting the router external port, please use 1024~5000 port. Do not use well-
known port 1~255 and the system port 256~1023 to avoid conflict.
: :It shows that the function of port mapping is enabled in this port.
90
Loading...