XR4116
INSTALLATION/OWNER'S MANUAL
AM/FM Receiver
XR4116 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
• Remove 2 transit screws located on top of the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting
sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
KEYS
INSTALLATION
MOUNTING KIT
MOUNTING
SLEEVE
HEAD
UNIT
OR DASHBOARD
TYPICAL FRONT-LOAD
DIN MOUNTING METHOD
2
XR4116 INSTALLATION
Wiring Diagram
Antenna
Connector
10 AMP
AGC Fuse
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse could
damage the radio.
The unit uses one
10 amp AGC fuse located
in-line.
3
XR4116 OPERATION
Control Locations
1
18
1 10
2 11
3 12
4 13
2 3 4
13 12 11 10 9 8 71617
1415
Power
Volume Knob
Audio / Menu
USB Port
Preset 3 / Intro
Preset 2 / Random
Preset 1 / Repeat
Display
5
6
5 14
Reset
Auxiliary Input
6 15
Preset 6 / Folder Up
7 16
Preset 5 / Folder Down
8 17
Preset 4 / Play / Pause
9 18
Tune Up
Tune Down
Band / Go Back
Mode
Mute
4
XR4116 OPERATION
General Operation
Power On/Off
Mode
Display
Reset
Set the Clock
Press or any other button to turn the unit on. Press
again to turn the unit off.
Press MODE to select between AM/FM, USB or auxiliary
input modes. Modes of operation are indicated in the
display. USB mode will not appear unless a USB device
is connected.
The radio frequency (tuner mode) or MP3 title/track
information (USB mode) will be shown by default. Press
DISP to display the clock. The default display will return
after five seconds.
When in USB mode, the display will alternate between
track number/elapsed time and available MP3
information, including file name, song title, artist name,
album name and folder name.
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located in the top right
corner.
Press DISP to display the clock, then press and hold
DISP until the hours will flash. Rotate the volume knob
to adjust the hours. Press the volume knob, and the
minutes will flash. Rotate the volume knob to adjust the
minutes.
Auxiliary Input
Volume
Preset EQ Curves
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc.
Adjust volume using the volume knob (00-40).
Press EQ to select between the following preset
equalization curves: FLAT, POP, JAZZ, ROCK and OFF.
Note: Ability to manually adjust Bass and Treble settings
is disabled when a preset equalization curve is selected.
Setting equalization curves to OFF enables manual Bass
and Treble adjustments.
5
XR4116 OPERATION
STEREO
General Operation
Audio / Menu
Bass
Treble
Balance
Fader
Loudness
EQ
Distance Tuning
Press the volume knob to select between Bass, Treble,
Balance, Fader, Loudness, Distance and Stereo.
BASS
TREBLE
BALANCE
FADER LOUDNESS
EQ DISTANCE
Press the volume knob until BAS appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
Press the volume knob until TRE appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
Press the volume knob until BAL appears.
Rotate the volume knob left/right to adjust.
10L (left) to 10R (right). "L=R" represents equal balance.
Press the volume knob until FAD appears.
Rotate the volume knob left/right to adjust.
10R (rear) to 10F (front) "F=R" represents equal balance.
Press the volume knob until LOUD ON or LOUD OFF appears,
then rotate the volume knob to select desired option.
Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes.
Press EQ, then turn the volume knob to cycle through the
equalization curves: FLAT (default), POP, JAZZ, CLASSIC,
BEAT, ROCK and USER. Any manual adjustment to the Bass
or Treble settings are automatically saved as USER.
From tuner mode only, press the volume knob until DX
or LOCAL appears, then rotate the volume knob to select
desired option. Selecting LOCAL programs the unit to stop at
only strong stations when seek tuning.
Stereo / Mono
From tuner mode only, press the volume knob until STEREO
or MONO appears, then rotate the volume knob to select
desired option. Selecting MONO can improve listening in
areas with a weak FM signal.
Audible Beep
Press and hold the volume knob until BEEP ON or BEEP
OFF appears, then rotate the volume knob to select desired
option. Activating this feature programs the unit to beep each
time certain buttons are pressed.
Area Selection
From tuner mode only, press and hold the volume knob
until BEEP ON or BEEP OFF appears. Press the volume knob
again to display AREA USA or AREA EURO, then rotate the
volume knob to select option appropriate for your location.
12/24-Hour Clock
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10.00). In European frequency spacing
mode, the clock will display 24-hour time (22.00).
6
AM/FM Tuner Operation
XR4116 OPERATION
Seek Tuning
Manual Tuning
Band
Storing and Recalling
Station Presets
USB Operation
Connecting a USB Device
(sold separately)
Playing Music
Track Select
Fast Forward and
Reverse
Pause
Displaying Information
Press TUNE
next strong station.
Press and hold TUNE
appears, then press TUNE
to change radio frequency up or down one step at a time.
Press and hold to advance quickly.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
To play MP3 files from most USB mass storage devices, line
up the USB connector and insert the USB device into the
unit's USB port.
When a USB device is first connected, “LOAD” will appear in
the display and playback will begin momentarily. Depending
on the number of files and folders, it may take several
seconds for the device to begin playing. If no valid MP3 files
are detected, “NO FILE” will be displayed and the last mode
will be resumed.
Press TRACK
track. Press TRACK
current track. Pressing TRACK
beginning of the previous track.
Press and hold TRACK
control to fast forward or reverse a track.
Press
Press
ID3 tag and file/folder information will be automatically
changed during playback. Press DISP to view the clock.
Default display will resume after five seconds.
/ II to temporarily stop USB playback.
l
/ II again to resume playback.
l
or TUNE
nn
nn
to skip to the beginning of the next
ll
nn
ll
momentarily to seek to the
ll
or TUNE
or TUNE
nn
to return to the beginning of the
nn
or TRACK
until "MANUAL"
ll
again skips to the
momentarily
ll
on the remote
nn
7
XR4116 OPERATION
USB Operation
Repeat
Random
Intro
Character Support
Media Compatibility
Press RPT to choose between:
• Current Song - Continuously repeats selected track.
• Current Folder - Continuously repeats all files in folder.
Press RDM to choose between:
• Off - Cancels RDM function.
• All Songs - Plays all tracks in random order.
• Current Folder - Plays all tracks in folder in random
order.
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• Off - Cancels the INT function.
• All Songs - Plays first 10 seconds of each track.
• Current Folder - Plays first 10 seconds of each track in
folder.
Maximum character display information
• Track name – 64 character maximum
• Directory name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
• *Album name – 64 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3 file.
The following types of files are compatible:
• MP3 data
The following types of files are not compatible:
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
8
MP3 playback sequence is based on order the files are
copied to the USB device and begins in the root folder. Any
empty folders or folders that do not include MP3 files are
skipped. Depending on your software, the playback order
may vary.
XR4116 OPERATION
USB Operation
Playback Capacity
USB Device Compatibility
Additional MP3
Information
Sampling Frequency
Rates
Transfer Bit rates
MP3 Tag Display
• Maximum number of files: 1024
• Maximum number of folders: 512
• Maximum number of folder levels (sub folders): 8
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note: Devices that exceed the maximum number of files or
folders may not function properly.
Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility. USB devices must be 32GB or
smaller in capacity to be compatible.
Only MP3 files with filename extension (.mp3) can be played.
Do not attempt to play non-MP3 files with the MP3
extension.
8kHz ~ 48kHz
8kbps ~ 320kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
9
XR4116 OPERATION
Troubleshooting
Problem Cause Action
Yellow wire not connected or incorrect
Unit will not turn on
(no power)
Unit has power
(but no sound)
Unit blows fuses
NO FILE appears
on display
NO SUPPORT appears
on display
voltage Red wire not connected or
incorrect voltage
Black wire not connected Check connection to ground
Fuse blown Replace fuse
Speaker wires not connected Check connections at speakers
One or more speaker wires touching
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Speaker wires touching chassis ground Check for pinched wire
Incorrect fuse rating Use fuse with correct rating
No playable MP3 files found on the
device
An invalid ID3 tag version is present
Insulate all bare speaker wires
Version 1.0 to 2.0 ID3 tags are
Check connections for proper
voltage (11~16VDC)
from each other and chassis
ground
Check for pinched wire
Check the device for valid
MP3 files
supported.
10
XR4116 OPERATION
Limited One Year Warranty
This warranty gives you specific legal
rights. You may also have other rights
which vary from state to state.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
Who is covered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered:
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
license conditions and copyright notices for
the software can be found via www.dualav.
com.
What to do?
1. Before you call for service, check the
2. If you require service during the
3. Please describe your problem in
4. For more information and for the
Exclusion of Certain Damages: This
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
or imputed. No person or representative
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
authorized service center.
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
location of the nearest authorized
service center please contact us by one
of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
11
XR4116 OPERATION
Specifications
FM Tuner
AM Tuner
General
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 10dBf
50dB quieting sensitivity: 25dbu
Stereo separation @ 1kHz: >30dB
Frequency response: 30Hz-13kHz
Tuning range: 530kHz-1710kHz
Usable sensitivity: <42dBu
Frequency response: 30Hz-2.2kHz
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts RMS
Dimensions: 7" x 7" x 2" (178 x 178 x 50 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 7 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 70dBA (reference: 1 watt into 4 ohms)
12
XR4116 OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
13
Dual Electronics Corp.
Toll Free: 1-866-382-5476
9AM-5PM EST, Monday-Friday
©2015 Dual Electronics Corp. All rights reserved.
Other trademarks and trade names are those of their respective owners.
www.dualav.com
NSA1015-V01
Loading...