DSC DSC-ID65DSS User Manual

High Resolution Vandal Proof Dome Camera
3-Axis Vertical / Horizontal / Rotation
DSC-ID65DSS
Feature:
1/3” COLOR CCD High Resolution Color 540TVL D/N 600TVL Starlight 0.001Lux Super (SDNR) Digital Noise Reduction Digital Slow Shutter (DSS) 2.8~11mm Varifocal Auto Iris Lens IR Cut On Screen Display (OSD) set-up Menu Vandal Proof IP66 Housing 3-Axis Bracket
Specification:
Camera types 1/3" SONY CCD Sensor Signal System NTSC / PAL Effective Picture Elements NTSC: 771(H) x 492(V); PAL: 753(H) x 582(V) Resolution Color: 540TV Lines D/N: 600TV Lines Mini Illumination Legacy Mode:0.01 Lux / F1.2 Starlight Mode: 0.0014 Lux / F1.2 Scanning System Internal / Line-Lock S/N Ratio more than 50dB / 58dB (TYP) (Gamma, Aperture, AGC OFF) Auto Iris A.E.S / DC-IRIS OSD Display On Screen Display for all Control Mirror Function Select by OSD or SW Horizontal / Vertical / Rotation Rotation 3 Axis White Balance Push / Indoor / Outdoor / User / ATW Gain Control Select by OSD Auto / Manu (Auto 30dB Max.) Back Light Compensation On / Off Gamma Characteristic 0.45 / 1.0 Lens Furnished 2.8 ~11 mm Vari-focal Auto Iris Lens IR Cut Yes DNR Dynamic 2 / 3D DNR
Electronic Shutter
Day & Night Auto (Level adjustable), Color, B/W Video Output 1.0 Vp-p Composite Video / 75Ω Power Supply AC 24V / DC 12V ± 10% 250mA Dimension Ø145 x 106(H) mm Weight 2 lbs (907 g) without Bracket Operating temperature 14°F ~ 122°F ( -10°C ~ 50°C) Humidity 10% ~ 85% RH Storage temperature -22°F ~ 140°F ( -30°C ~ 60°C)
*** All Specifications are subject to change without notice.
A.E.S. 1/50 ~ 1/120,000 sec. FIX. 1/100,1/120,1/180,1/350,1/500,1/750,1/1000,1/2000,1/4000,1/10000 sec.
Dual Power: DC 12V /AC 24v
** Designed in U.S.A
3 8-001-0735-01(A1)
OSD MENUAL
There are connected to 4 direction switch [UP],[DOWN],[ENT],[PRI],push the [ENT] switch up to 1~2 second, a pretty menu will be pop-up on your screen. You may now push [UP] or [DOWN] switch to browse around menu.
1. SETUP MENU
You may now push "UP" or "DOWN" bottom to browse around two page menu.
2. IRIS
This is used to control the iris & shutter speed of the lens. It included 3 items “PEAK”, “ALC”, “AES”.
PEAK」:PEAK is used to control the reaction of auto iris, which is based on the average light of
picture signal or the light rate of the peak.
ALC」:ALC is used to select AUTO or FIX. Adjust IRIS level
AES」:AES is used to select electronic shutter be AUTO or FIX function, at AUTO mode can be
adjust AES level,at FIX mode can be selector shutter speed at below, [OFF],[1/100sec],[1/120sec],[1/180sec],[1/350sec],[1/500sec],[1/750sec]
[1/1000sec],[1/2000sec],[1/4000sec],[1/10000sec].
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
4 8-001-0735-01(A1)
3. AGC . SENS
This is used to select「AGC」and「SENS」function.
AGC」:To adjust auto gain control can be select [AUTO] or [FIX] 9 steps adjustable, 6dB,9dB,
12dB,15dB,18dB,21dB,24dB,27dB,30dB 。 SENS」:For low light application can be select [AUTO] or [OFF],9 steps adjustable at AUTO Mode to set max accumulate field number NTSC MODE 2,4,6,8,10,12,16,32,60。 PAL MODE 2,4,6,8,10,12,16,32,50。
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
4. BACKLIGHT
This is used to control “BLC” (Back Light Compensation),
BLC」:ON / OFF selector. Selector[ON]has sub-items[AREA].
AREA」: 48 BLC zones can be set separatly. According to the mask area (BLC zone) signal
to decide the iris level and shutter speed.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
5 8-001-0735-01(A1)
5. XDR
This is used to select XDR (extend dynamic range) function. The simulation of wide dynamic is capable of improving the illumination of dark area and restraining strong light of bright area.
「OFF」 :XDR mode off 「LOW」:XDR range is low 「MID」 :XDR range is middle 「HIGH」:XDR range is high
6. WHITE BALANCE
This is used to control the color ON/OFF and white balance and the gain rate of RED & BLUE color.
COLOR
Selector MONOCHROM mode burst signal will be off, display is monochrome image, select OFF mode is display monochrome image but burst signal is on,select ON mode is normal color image,select AUTO mode at low light AGC up, display image will be auto change to monochrome image.
「WB」
White balance control,ATW is Auto trace white balance,can be adjust offset level.
Move arrow from ATW to AWB it will lock the current color temperature at the same time, can be adjust offset level .
GAIN
The gain rate of R-Y & B-Y can be adjusted separately.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
6 8-001-0735-01(A1)
7. GAMMA / ENHANCE
This is used to select the camera gamma correction.
GAMMA
Select TYPE-1gamma is 0.45, TYPE-2 gamma is 1.0
ENHANCE
Adjust enhance level.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
8. DAY / NIGHT
This is used to select the DAY / NIGHT operation mode. OFF」:Select this mode will be operation at the DAY mode AUTO: Select this mode when AGC is up to max but image luminance still insufficient, will be
increment digital gain +6dB display will be change to monochrome image. When image luminance is sufficient AGC reduce to +6dB,digital gain will be off image change to color.
When DAY/NIGHT mode change can be select delay time at the 1, 5, 10, 20, 30, 40, 50,
60,sec.
EXT: Select this mode DAY/NIGHT mode change is by external signal. After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
7 8-001-0735-01(A1)
9. DIGITAL ZOOM
This is used to select the DIGITAL ZOOM & DIGIT AL PAN / TITEL operation mode.
OFF」:Select this mode digital zoom is off. ON」:Select this mode digital zoom is four times, At the this mode can be move “ZOOM POSITION”,
use [UP] & [DOWN] key move curse to POSITION,push down [ENT] key after use [UP] & [DOWN] key select H/V direction,after use [UP] & [DOWN] key move the“ZOOM POSITION”.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
10. H/V REVERSE
This is used to select image「Horizontal Reverse」and「Vertical Reverse」function.
H-REVERSE
Horizontal Reverse (Mirror) ON/OFF
V-REVERSE
Vertical Reverse (Up-side down) ON/OFF
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
8 8-001-0735-01(A1)
11. MOTION DETECT
This is used to select the montion detcet function.
OFF」:Motion detect function is OFF.
「ON」:
Motion detect function is ON.
AREA」:At the this mode can be select motion detect area, use [UP] & [DOWN] key move gray
block to detcet position push[ENT] set the position repeat the operation still all detcet
position is mask by gray block, push [PRI] leave this setting.
TIME」:Select motion detects output time.
SENS」:Motion detect sensitive adjust.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
12. LANGUAGE
This is used to select the OSD manu language.
ENGLISH」: English mode
JAPANESE」: Japanese mode
Push [PRI] key to go back to the main menu page.
9 8-001-0735-01(A1)
13. MASK
This is used to select mask area size and position and mask area display ON or OFF.
「NO」:
Select 1~4 mask area number.
OFF」:Mask area display is off.
「ON」:
Mask area display is on, can be use [UP] & [DOWN] key set mask area size and position .
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
14. OSD
This is used to select on screen display ON / OFF select.
MONTION」:Montion action display ON / OFF select.
ZOOM MAG」Zoom times display ON / OFF select.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
10 8-001-0735-01(A1)
15. CROSS LINE /FREEZE
This is used to select display a cross line on screen ON or OFF.
LINE」:Cross line display ON/OFF select.
FREEZE」:Image freeze ON/OFF select.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
16. POSI / NEGA
This is used to select image positive and negative.
OFF」:Image Display is normal image.
「ON」:
Image Display is negative image.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
11 8-001-0735-01(A1)
17. TITLE
This is used to set up the ID figures & position on the screen. (Title setting)
「」:
Horizontal start position selector, use [UP] & [DOWN] key move cursor to select position, push [ENT] set the position after use [UP] & [DOWN] move cursor to select character, push[ENT] set the character to select position.
POSITION」:Select character display is OFF or display position UP or DOWN selector.
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
18. PRESET
This is used to select PRESET on/off and lin lock on/off & phase adjustment.
PRESET」:Select preset ON/OFF mode. ID」:RS-485 commection ID number select. (This function not yet release)
After setting, push [ENT] memory set state, After push [PRI] key to go back to the main menu page.
12 8-001-0735-01(A1)
Loading...