DSC GS2065, TL265GS, Alexor GS2065, Alexor TL265GS Technical Training Manual

Overview:

The GS2065 provides primary or backup GSM/GPRS communication for the PC9155 2-way wireless security
suite

Specifications:

Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx15mm)
Weight : 68 g
Input Voltage : 10 to 13.8 V (from the PC-Link header)
Current Draw : 100 mA at 12V (400 mA during the GSM transmission)
Operating Environment : 40 to 104 F (5 to 40 C)

Features:

Back up and primary GSM/GPRS alarm communication
Panel remote uploading/downloading support via GSM/GPRS
Supervision heartbeats via GSM/GPRS
128-bit AES encryption over GSM/GPRS
Full event reporting
SIA format
PC-Link connection
SIM card included
Signal strength and trouble display
Activating and initializing through Connect 24
Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz

Compatible Receivers:

Sur-Gard System I Receiver:
version 1.10 and higher

Sur-Gard System II Receiver:
version 2.00 and higher

Sur-Gard SG-DRL3-IP: version 2.20
and higher (for Sur-Gard System III
Receiver)

Overview:

The TL265GS is an Internet and GSM/GPRS Dual-Path alarm communicator for the PC9155 2-way
wireless security suite

Specifications:

Dimensions : 3.937"x5.875"x0.75" (100mmx150mmx18mm)
Weight : 78 g
Input Voltage : 10 to 13.8 V (from the PC-Link header)
Current Draw : 100 mA at 12V (400 mA during the GSM transmission)
Operating Environment : 40 to 104 F (5 to 40 C)

Features:

Fully redundant Internet and GSM/GPRS dual-path alarm communication
Integrated call routing
Panel remote uploading/downloading support via GSM/GPRS and Internet
Supervision heartbeats via GSM/GPRS and Internet
128-bit AES encryption via GSM/GPRS and Internet
Full event reporting
SIA format
PC-Link connection
SIM card included
Signal strength and trouble display
Activating and initializing through Connect 24
Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz

Compatible Receivers:

Sur-Gard System I Receiver: version

1.10 and higher
Sur-Gard System II Receiver: version

2.00 and higher
Sur-Gard SG-DRL3-IP: version 2.20

and higher (for Sur-Gard System III
Receiver)

BEFORE YOU BEGIN

Have the following ready before installation:

Control panel backup battery
Battery connection harness
Batteries for WT5500 2-way wireless keypad
Screwdriver

Prior to installing a GS2065 and TL265GS, contact your monitoring station to determine if it is a master reseller or
visit www.connect24.com and become an authorized dealer. In both instances, you will acquire a Profile Number,
Installer ID Number and an Installer Password.

PLEASE NOTE: You need to activate the SIM card and initialize the communicator 24 HOURS BEFORE

INSTALLATION (Steps 1).

Summary of Installation Steps

Step 1 – Initialize an account via Connect 24 Website (www.connect24.com)

Step 2 – Install and wire the communicator to the control panel (on-site)

Step 3 – Load the programming and test for best signal strength location

Step 4 – Program communication options on the control panel via keypad

Step 5 – Test communicator

Step 1 – Initialize an account via Connect 24 Website (www.connect24.com)

Login to Connect 24 website by using Installer ID and Password and initialize an account

Select Profile Number
Select Product Module
Enter SIM card number
Enter DNIS number (if necessary)
Enter Account Code
Select Supervisory Type (if necessary)
Enable DHCP (if necessary)
Enter IP Address (TL260GS/TL265GS only)
Enter Subnet Mask Address (TL260GS/TL265GS only)
Enter Gateway Address (TL260GS/TL265GS only)
Select Rate Plan
Confirm information and submit activation application

Step 1 – 1

Select Profile Number

Select Profile

Step 1 – 2

Select Product Module

Select Module Number