®
Installation Instructions
Floating Mounting Bracket for Targa, Premier,
Premier/C and Luma 2 Projection Screens by Draper
Caution
① Read instructions through completely before proceeding.
② Follow instructions carefully. Installation con trary to instructions in val i dates
warranty.
③ Should be installed level and with bottom edges in alignment.
④ Hardware for assembling Floating Mounting Brackets and attaching to
screen case is provided; it is the responsibility of the installer to provide
the appropriate hardware for suspending or otherwise mounting the
brackets to the wall or ceiling.
Wall Mounting
① Mount two Sliding Wall Brackets to the mounting surface. Brackets should
be placed on studs. Installer must insure that fas ten ers used are of ad equate strength and suit able for the mounting sur face cho sen.
Please Note: Sliding Wall Brackets can be mounted so they can be
located at any point along the Case Attachment Brackets (within 24" of
each end of case). They must be mounted level, and with bottom edges
in alignment.
② Place front brackets on screen case, making sure the lower curled edge
engages the screen case (see Fig. 1).
Figure 1
③ Place screen case on clean, steady surface with the back of the screen
case facing up.
④ Remove the bottom screw from each endcap (see Fig. 2).
⑤ Attach Case Attachment Brackets to screen case by re-using endcap
screws. Also use provided 10-32 x ½" PPH Zinc Machine Screws, attaching
through the wall mounting holes on the endcaps (see Fig. 2).
Figure 3
Ceiling Mounting
① Attach two Sliding Wall Brackets to Ceiling Brackets using .250-20 x ¾"
Phillips Pan Head Machine Screws and .250-20 Nylon Inserted Hex Zinc
Locking Nut (provided—see exploded diagram on page 2).
② Mount two Ceiling Brackets to the mounting surface. Brackets should be
located at joists. Installer must insure that fas ten ers used are of adequate
strength and suit able for the mounting sur face cho sen.
Please Note: Sliding Brackets can be mounted so they can be located at
any point along the Case Attachment Brackets (within 24" of each end of
case). They must be mounted level, and with bottom edges in alignment.
③ Place front brackets on screen case, making sure the lower curled edge
engages the screen case (see Fig. 1).
④ Place screen case on clean, steady surface with the back of the screen
case facing up.
⑤ Remove the bottom screw from each endcap.
⑥ Attach Case Attachment Brackets to screen case by re-using endcap
screws. Also use provided 10-32 x ½" PPH Zinc Machine Screws, attaching
through the wall mounting holes on the endcaps (see Fig. 2).
Please Note: Make sure to hook bottom of Case Attachment Bracket
under the bottom of the screen case (see Fig. 1).
⑦ Attach Case Attachment Brackets to front brackets using 10-32 x ½" PPH
Zinc Machine Screws (provided).
⑧ Mount screen case to wall brackets by slightly angling the upper slots on
the Case Attachment Brackets into the upper channel on the Sliding Wall
Brackets, then rotating screen case into place (see Fig. 4).
⑨ Once the screen is placed in the desired position, secure screen case to
Sliding Wall Brackets using #10-32 x 1" Pan Head Screws (provided)
(see Fig. 4).
Please Note: For dimensional, exploded and assembled
Figure 2
Please Note: Make sure to hook bottom of Case Attachment Bracket
under the bottom of the screen case (see Fig. 1).
⑥ Attach Case Attachment Brackets to front brackets using 10-32 x ½" PPH
Zinc Machine Screws (provided—see exploded diagram on page 2).
⑦ Mount screen case to wall brackets by slightly angling the upper slots on
the Case attachment Brackets into the upper channel on the Sliding Wall
Brackets, then rotating screen case into place (see Fig. 3).
⑧ Once the screen is placed in the desired position, secure screen case to
Sliding Wall Brackets using #10-32 x 1" Pan Head Screws (provided) (see
Fig. 3).
drawings, please see page 2 of these instructions.
If you encounter any diffi culties installing your Floating Mounting Brackets, call
Copyright © 2012 Draper Inc. Form FloatingMountingBracket_Inst12-R2 Printed in U.S.A.
your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; fax (765) 987-7142.
Figure 4
Floating Mounting Bracket by Draper
9
4
1
2
1
Dimensions
1½"
Page 2 of 2
25½"
"
8
/
5
2
2¾"
REAR VIEW
Exploded Drawing
⑨
⑥
Parts List
ITEM QTY DESCRIPTION
1 2 Bracket, Front Case
2 1 Bracket, Right Case Attachment
3 1 Bracket, Left Case Attachment
4 6 Screw 10-32 x ½" PPH Zinc Machine
5 2 Screw, #10-32 x 1" Long Phil Pan Hd Zinc
6 2 Bracket, Ceiling Mounting
7 2 Bracket, Sliding Wall
8 4 Nut, .250-20 Nylon Inserted Hex Zinc Locking
9 4 Screw, .250-20 x ¾" Phillips Pan Head Machine
⑤
FRONT VIEW
⑧
⑦
2"
24¾"1½" ¾"
④
②
⑥
⑦
③
⑧
3½"
SIDE VIEW
"
8
/
7
1
①
④
⑨
Completed Assembly Drawing
⑤
www.draperinc.com
(765) 987-799
Loading...