Doughpro Proluxe SL1577K Service Manual

Operations Manual

rev8-71713

Model: SL1577K
Split Lid Grill

formerly DOUGHPRO. New Name. Same Quality. Superior Service.

proluxe.com

Operation Instructions

Please read carefully before attempting to use this appliance.

Step 1. Carefully unpack and clean grill plates with mild soap then sponge clean

with cold water.
Step. 2. Place in location where it will be used allowing for clearances per th e

dimensions indicated.
WARNING! Allow 2” minimum clearance between adjacent equipment and/or

wall areas.

Do not touch hot surfaces.
Step 3. Plug into proper 3 prong wall outlet. If other appliances are connected

to the same circuit make sure the total load does not exceed maximum
ampacity of the circuit. Electrical information is as follows:

120V/60Hz/1 phase/2200W/18.3 Amps
208V/60Hz/1 phase/2800W/13.5 Amps
220V/60Hz/1 phase/2200W/10.0 Amps

Step 4: Warm-up

on. The display flashes and shows left preset timer during warm-up. Pre­ heat temperature time will be 40-50 minutes. When the set point is
reached, the display stops flashing and beeps 3 times.

Step 4: Operation

Energize by turning on the power switch which will illuminate when turned

Simply place product on either side of the grill, close lid and press the

desired pre-set time cycle 10 or 20 seconds. After the time cycle is
finished press it again to reset the time cycle.

Cleaning Instructions

NOTE! Always turn off power and allow to cool down before attempting to clean.

Never submerge grill in water or other liquid nor use mineral spirits
or other flammable material to clean this appliance.

!Never use ice to cool down grill, warranty will be void!

Clean stainless steel and griddle surfaces with soap and water using a
soft, clean cloth periodically as required, but at least once daily. Never
use harsh abrasives. Use only non-abrasive scouring pads when required.

Clean Cycle

275°F is the factory default temp for the CLEAN cycle. To change the CLEAN cycle temp, simultaneously

hold down the TEMP and CLEAN buttons for 15 seconds. The current temp setting will display on the

right digital display only. Using the up or down arrows to adjust to the desired temp.

To start a clean cycle, push CLEAN button once so the CLEAN LED light is turned on. All preset LED’s are

turned off, and the temperature set point is changed to the clean set point of 275°F. This also initiates

the cool down to clean set point condition as well the display starts flashing until the clean set point is

reached.

To stop the clean cycle, simply press the CLEAN button once to deactivate the clean cycle. The CLEAN

LED is turned off, the preset LED’s are restored, the temperature set point is changed to the main set

point. Again, the warm-up condition is initiated and the display flashes until the cook set point is

reached.

*

* 275° is the factory default temp for the CLEAN cycle. To change the CLEAN cycle temp,

simultaneously hold down the TEMP and CLEAN buttons for 15 seconds. The current temp setting will

display on the right digital display only. Using the up or down arrows to adjust to the desired temp.

SL1577 Operating Instructions:

1. Press desired time to start the time cycle. After the cycle is finished, press it again to
reset the time cycle

HOW TO FIND TEMPERATURE

1. To find the temperature of the UPPER PLATENS:
Press the TEMPERATURE button and the ARROW UP button at the same time.

2. To find the temperature of the LOWER PLATENS:
Press the TEMPERATURE button and the ARROW DOWN button at the same time

Instruction’s for Adjusting the Temperature

PRESS and hold the TEMP and
ARROW up
buttons simultaneously for 15

seconds.

The current temperature setting
will display on the right
digital display only.

Using the ARROW buttons, you
may now adjust the temperature
to your
desired setting.

Once you have set your desired
temperature simply push
the TEMP button. The digital
displays will now read the
preset times.

Instruc

tion’s for Adjusting the Set-Time

Pres

s the TEMP button first and then the

desired timer button and continue to hold
both for 5 seconds.

The digital displays will now read their preset
times as shown here. Each side is capable of
having up to 4 different settings, making a total
of 8 set-times.

Now using the ARROW buttons you
can set your desired time.

Once you have set the desired time simply press the

TEMP button, the unit will display the new set-time.

*IMPORTANT NOTE: When adjusting the time settings, The RIGHT SIDE time buttons

control the left side, so the same time you set on the right will automatically be set to
the left side accordingly. If you desire an additional set of times you can adjust the left
side AFTER you have adjusted the right side without effecting the right side settings.