EN
REFRIGERATION
RUA SERIES
RUA5208X, RUA6408X, RUA8408X
Absorption refrigerator
Installation Manual
EN
RUA5208X, RUA6408X, RUA 8408X Explanation of symbols
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
NOTE
I
You can find details on the operation in the operation manual.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
6 Installing the refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
7 Connecting the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1 Explanation of symbols
!
!
A
I
WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
NOTE
Supplementary information for operating the product.
3
EN
Safety instructions RUA5208X, RUA6408X, RUA 8408X
2 Safety instructions
The manufacturer accepts no liability for damage in the following cases:
•
Faulty assembly or connection
•
Damage to the product resulting from mechanical influences and incorrect
connection voltage
•
Alterations to the product without express permission from the manufacturer
•
Use for purposes other than those described in the operating manual
WARNING!
•
!
Never open the absorber unit. It is under high pressure and can cause
injury if it is opened.
•
Ensure clean and residue-free handling if silicone sealant or similar is
used. There is a risk of fire if silicone filaments come into contact with
hot parts or naked flames.
•
Do not operate the refrigerator if it is visibly damaged.
•
If the AC power cable for this refrigerator is damaged, it must be
replaced by the manufacturer, customer service or a similarly qualified
person in order to prevent safety hazards.
•
Never use a naked flame to check the refrigerator for leaks.
•
This refrigerator may only be repaired by qualified personnel. Inadequate repairs may cause serious hazards.
•
Only use universal LPG gas.
•
Only operate the refrigerator at the pressure shown on the type
plate. Only use pressure controllers with a fixed setting which comply
with national regulations.
•
Dismantle all refrigerator doors for the disposal of the old refrigerator
and leave the shelves in the refrigerator to prevent accidental enclosure and suffocation.
!
4
CAUTION!
•
Danger of crushing! Do not put your fingers into the hinge.
•
Before starting the device, ensure that the power supply line and the
plug are dry.
EN
RUA5208X, RUA6408X, RUA 8408X Scope of delivery
NOTICE!
•
A
Only hold the refrigerator at the body of the refrigerator during transport. Never hold the refrigerator at the absorber unit, the cooling fins,
the gas pipes, the door or the control panel.
•
Make sure that the refrigerator circuit is not damaged during transportation. The refrigerant in the refrigerator circuit is highly flammable.
In the event of any damage to the refrigerator circuit (smell of ammonia):
– Switch off the refrigerator if applicable.
– Avoid naked flames and sparks.
– Air the room well.
•
Do not install the refrigerator near naked flames or other heat sources
(heaters, direct sunlight, gas ovens etc.).
•
Danger of overheating!
Always ensure sufficient ventilation so that the heat generated during
operation can dissipate. Make sure that the refrigerator is sufficiently
far away from walls and other objects so that the air can circulate.
•
Check that the voltage specification on the type plate is the same as
that of the power supply.
•
Do not open the refrigerant circuit under any circumstances.
•
Only use the AC connection cable supplied to connect the refrigerator to the AC mains.
•
Only use cables with a suitable size.
•
Never pull the plug out of the socket by the connection cable.
•
The refrigerator may not be exposed to rain.
3Scope of delivery
Quantity Description
1 Refrigerator
1Drain hose
1 Bottom trim piece
1 Sealing strip (fitted underneath during installation)
1 Installation and Operating Manual
5
EN
Accessories RUA5208X, RUA6408X, RUA 8408X
4Accessories
Available as accessories (not included in the scope of delivery):
Description
LS300 ventilation grille
Dometic gas flue kit 3776
RUA5208X only: Door reversing kit
All the accessories are available from specialist dealers. If you have any questions,
please contact the dealer or your service partner directly.
5 Intended use
The refrigerators are designed for installation in caravans or motorhomes. They are
only suitable for cooling and storing foodstuffs. The refrigerators are not intended for
the proper storage of medicine.
The refrigerators are designed to be operated on a DC power supply, AC mains
power supply or universal LPG gas.
6 Installing the refrigerator
6.1 Preparing the installation
When installing the refrigerator, note the following:
•
Ensure that the floor is solid and level.
•
Ensure that the refrigerator is level.
•
The refrigerator must be installed so that it is easily accessible for service work,
easy to de-install and install and can be easily removed from the vehicle.
6
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
1
W
H
B
D
A
C
RUA 5208X
W
H
B
D
A
C
RUA 6408X
RUA 8408X
2
7
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
RUA 5208X
RUA 6408X, RUA 8408X
5
6
3b
3a
4
1
2
5
6
3b
3a
4
1
2
7
7
3
•
The refrigerator must be installed in a recess so that it stands secure when the
vehicle is in motion. Note the following dimensions (fig. 1 and fig. 2):
RUA5208X RUA6408X RUA8408X
Refrigerator Overall dimension in mm
Height (A) 1191 1447 1657
Width (B) 550 550 550
Depth (C)
(excludes control knob 5mm)
Recess Dimension in mm
Height (H) 1181 – 1186 1437 – 1442 1647 –1652
Width (W) 530 – 535 530 – 535 530 – 535
Depth (D) min. 621 min. 621 min. 621
677 677 677
Installation with two side vents
8
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
Pos. in fig. 3,
page 8
1 Insulation wool on top and sides of cabinet
2 Recommended maximum clearance 25 mm
3 LS 300 ventilation grille
4 Minimum height is equal to the height of the cabinet
5 Dometic gas flue kit 3776
6 Air deflection plate
7 Floor vent, min. 40 mm (only required if lower air inlet vent is not flush to
•
The outer wall must be fitted with one air inlet ventilation grille (fig. 3 3a,
Description
the floor)
page 8) and one outlet ventilation grille (fig. 3 3b, page 8) so that the heat
generated can be easily released to the outside:
– Lower air inlet vent LS300 must be installed flush to the vehicle floor.
– Upper air outlet vent LS300 must be installed with the bottom of the vent no
lower than equal to the top of the refrigerator cabinet, the bottom of the top
vent can be higher than the cabinet.
•
Fit an air deflection plate (fig. 3 6, page 8) above the condenser so that the heat
does not accumulate in the vehicle.
•
Put insulation wool (fig. 3 1, page 8) on top and sides of the cabinet.
•
If the lower ventilation grille of the air inlet vent cannot be installed flush to the
floor, an additional vent (fig. 3 7, page 8 and fig. b, page 16) must be provided in the floor for releasing any possible gas leakage.
•
The distance between the refrigerator and the rear wall must be at least 10 mm.
9
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
10 – 25
>25
>25
RUA 5208X
4
10 – 25
>25
>25
RUA 6408X, RUA 8408X
5
10
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
RUA 5208X
RUA 6408X, RUA 8408X
5
3
4
1
6
2
5
3
4
1
6
2
7 7
6
•
The recommended maximum distance between the refrigerator and the rear wall
is 25 mm. A distance of more than 25 mm between the refrigerator and rear wall
leads to poor performance and increases the power consumption of the
refrigerator. Reduce the space behind the refrigerator to maximum 25 mm to
create adequate air inlet and outlet ventilation corridor (fig. 4 and fig. 5). Use
a ventilation plate, for example, to do this.
Installation with one lower side vent and one roof vent
11
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
7
Pos. in fig. 6,
page 11
1 Insulation wool on top and sides of cabinet
2 Recommended maximum clearance 25 mm
3 LS 300 ventilation grille
4 Minimum height is equal to the height of the cabinet plus 150 mm
5 Dometic gas flue kit 3776
6 Roof vent
7 Floor vent, min. 40 mm (only required if lower air inlet vent is not flush to
•
If the minimum distance between the air inlet and outlet vents cannot be met, a
Description
the floor)
roof vent must be installed instead of the air outlet vent.
– The roof vent should be installed directly above the back of the refrigerator as
far as this is possible. Use an air duct if you need to install the roof vent
(fig. 6 6) offset, otherwise heat will accumulate there.
≥ 300
1
2
– If a roof air conditioner is installed, the distance between the roof vent
(fig. 7 1) and the air outlet of the roof air conditioner (fig. 7 2) must be at
least 300 mm.
•
The refrigerator must not be installed at the side of the air inlet and outlet vents as
this leads to poor performance and increases the power consumption of the
refrigerator.
•
The air inlet and outlet vents must not be covered by vehicle parts (such as an
open door or by installing accessories such as bicycle racks) while operating.
•
A separate flue duct must be installed under the air outlet vent, see chapter
“Installing the flue duct” on page 19.
12
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
1.
2.
8
•
Install the refrigerator so that it is protected from excessive heat, as this leads to
poor performance and increases the power consumption of the refrigerator.
•
The electrical installation must comply with national and local regulations.
•
The gas installation must comply with national and local regulations.
– AS/NZS 5601.2 – Gas installations – LP Gas installations in caravans and boats
– AS/NZS 5601.1 – Gas Installations – General Installations
•
The refrigerator must be installed in a draught-proof location, see chapter “Installing the refrigerator in a sealed location separate to the living space” on page 13.
6.2 Installing the refrigerator in a sealed location
separate to the living space
Gas-powered refrigerators in caravans or motorhomes must be installed in a sealed
location. This means that the combustion air can not be extracted from the interior
and exhaust fumes are prevented from directly entering the living space.
A suitable seal must be provided and fitted between the rear wall of the refrigerator
cabinet and the interior of the vehicle. The purpose is to provide a seal between the
interior of the vehicle and the cooling unit and ventilation area behind the
refrigerator.
WARNING! Fire hazard!
!
Do not use flammable materials such as silicone sealants, foam or similar
for the draught-proof installation.
The manufacturer has applied a sealing strip to the rear surface of the front frame.
13
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
1.
2.
9
0
1
➤ Apply the sealing strip to all four sides of the bottom surface of the refrigerator
(step 1. in fig. 8 and fig. 9).
➤ Push the refrigerator into position (step 2. in fig. 8 and fig. 9). This then seals
the space behind the refrigerator to the interior of the vehicle.
OPTIONAL:
➤ If the refrigerator stands on a platform, install the bottom trim piece in order to
seal the space between the refrigerator and the platform.
– A sealing strip (fig. 0 1) is applied to the lower surface of the bottom trim
piece.
14
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
a
1
2
– Push the bottom trim piece with the four plugs (fig. a 1) into the holes on the
front frame of the refrigerator.
– Snap the three catches (fig. a 2) into the holes under the bottom frame of
the refrigerator.
6.3 Making air inlet and outlet vents
NOTE
I
At high ambient temperatures, the refrigerator can only provide its maximum cooling capacity if the optimum ventilation has been provided.
➤ Make a cut out in the wall to fit the LS300 for the upper and lower vent system,
see chapter “Preparing the installation” on page 6.
➤ If the lower ventilation grille can not be installed flush to the floor, make an air inlet
vent in the floor (fig. b, page 16) behind the refrigerator near the gas burner.
15
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
≥ 40 mm
b
➤ Shield the end of the opening with a deflector to prevent sludge or dirt from
getting inside while driving (fig. b).
If you have to use a roof vent instead of an upper wall vent:
➤ Cut out a section in the roof. Refer to the roof vent instruction manual for the
required dimensions. When doing so, observe the information, see chapter “Preparing the installation” on page 6.
6.4 Installing the drain water hose
➤ To avoid damage on the drain water hose, position the hole for the drain water
hose in a way, that the hose does not touch the boiler casing.
➤ Drill a hole through the floor at the rear of the refrigerator.
➤ Install the drain water hose through the drilled hole. Ensure, that the drain water
hose is long enough in order to drain the water outside of the vehicle.
➤ Ensure that the drain water hose is not kinked.
➤ Seal the area around the drain water hose.
16
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
3
2
1
c
d
e
6.5 Installing the ventilation grille
No. in fig. c Description
1Slider
2 Ventilation grille
3 Installation frame
➤ Ensure the installation frame is water resistant (fig. d).
➤ Insert the installation frame and screw it down tightly (fig. e). Use all the fixing
holes for this.
17
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
f
g
h
3.
➤ Fit the ventilation grille (step 1. and step 2. in fig. f).
➤ Insert the slider and lock the ventilation grille with it (step 3. in fig. f).
2.
1.
6.6 Install the roof vent
1
2
No. in fig. g Description
1 Hood
2 Installation frame
➤ Ensure the installation frame is water resistant (fig. h).
18
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
i
j
➤ Insert the installation frame and screw it down tightly (fig. i 1). Use all the fixing
holes for this.
➤ Insert the hood and screw it down tightly (fig. i 2).
6.7 Installing the flue duct
10
9
1
2
3
4
5
6
7
8
6
19
EN
Installing the refrigerator RUA 5208X, RUA6408X, RUA 8408X
1.
2.
k
min.
15 mm
1.
2.
3.
l
NOTE
•
I
Install the flue duct as follows:
Install the Dometic gas flue kit 3776. Contact the customer service
(see back page).
•
It is not recommended to install additional flue stacks, as this leads to
poor performance and increases the power consumption of the
refrigerator.
•
Mount the flue duct under the upper ventilation grille (fig. j 1).
➤ Make a rectangular opening in the outer wall of the vehicle (fig. k ).
– The opening must be as wide as the flue pipe (fig. j 3, page 19).
– The opening must be high enough that the flue pipe fits through at a 45°
angle.
➤ Insert the coil (fig. j 7, page 19) in the flue pipe (fig. j 8, page 19) of the
refrigerator.
➤ Place the T-piece (fig. j 4, page 19) on the adaptor (fig. j 5, page 19) and the
flue pipe (fig. j 8, page 19) of the refrigerator.
➤ Direct the T-piece at an angle of 45° towards the rear wall.
➤ Attach the T-piece, adaptor and flue pipe with a screw (fig. j 6, page 19).
20
EN
RUA5208X, RUA6408X, RUA 8408X Installing the refrigerator
m
➤ Install the mounting plate (fig. l).
➤ Fill the opening with fire-resistant material (e.g. stone wool (fig. l).
NOTE
I
➤ Slide the flue pipe at least 15 mm on the T-piece (fig. l).
➤ Attach the cover for the flue stack outside on the vehicle (fig. m).
In some installation situations, it is possible that the flue pipe would
extend too far out of the vehicle in its installed state. Shorten the flue
pipe to the correct length if necessary.
6.8 Securing the refrigerator
CAUTION!
!
I
➤ Push the refrigerator firmly into its final location with the front flange sitting hard
against the recess front.
Only screw through the bushes built into the refrigerator, otherwise
foamed components, including electrical wiring, can be damaged.
NOTE
Ensure that the screws are tight, even when under increased loads
(while driving).
21
EN
Connecting the refrigerator RUA5208X, RUA6408X, RUA 8408X
2
1
n
➤ Push the screws (fig. n 1) through the plastic bushes in the sides of the
refrigerator, and fasten into the recess walls.
➤ Fit the caps (fig. n 2) into the bushes.
7 Connecting the refrigerator
7.1 Connecting to the gas supply
NOTICE!
•
A
22
This refrigerator may only be connected to the gas supply by a specialist in accordance with the applicable guidelines and standards.
•
Only use cylinders of universal LPG gas fitted with an approved gas
pressure regulator. Compare the pressure information on the data
plate with the pressure information on the pressure regulator on the
gas cylinder.
•
Only operate the refrigerator at the pressure shown on the data
plate.
•
Only operate the refrigerator with the type of gas shown on the data
plate.
•
Please note the pressures which are permitted in your country. Only
use pressure controllers with a fixed setting which comply with the
national regulations.
EN
RUA5208X, RUA6408X, RUA 8408X Connecting the refrigerator
1
o
NOTE
I
It must be possible to shut off the refrigerator from the gas line separately by means
of a shut-off device. The shut-off device must be easily accessible.
➤ Connect the refrigerator securely to the gas supply (fig. o). Always use a back
up wrench when loosening and tightening connections.
➤ Have a leak test and a flame test performed by an authorised specialist after
professional installation. Ensure you are issued with a certificate of inspection.
The pressure of the gas supply must be 2.75 kPa. Check the pressure at
the test point before using the refrigerator (fig. o 1, page 23).
23
EN
Connecting the refrigerator RUA5208X, RUA6408X, RUA 8408X
p
7.2 Connecting the device to electrical power supply
NOTICE!
•
A
The electrical installation and repairs may only be performed by a
specialist in accordance with the applicable regulations and
standards.
•
The device can be connected to 12 V DC and 230 – 240 V AC
power supply.
•
The respective negative and positive cables of the DC connections
for heating and controls may not be joined with one another in a
caravan. This can cause electrical interference or damage to
electrical components.
•
DC connection to the heating element must be made to the vehicle
engine battery, connection only while engine is running (fig. p).
I
24
NOTE
•
The mains socket must be easily accessible so that you can unplug
the power cord if required, thereby disconnecting the refrigerator
from the power.
•
The plug of the AC connection cable must not be cut off.
•
The connection cables must be laid so that they do not come in
contact with hot parts of the unit/burner or with sharp edges.
•
Changes to the internal electrical installation or the connection of
other electrical components (e.g. extra third party fans) to the internal wiring of the refrigerator will void any claims from the guarantee
and product liability.
EN
RUA5208X, RUA6408X, RUA 8408X Connecting the refrigerator
1
2
5
4
3
67 8
12
11
9
10
13
14
17
21
20
22
24
19
18
23
26
27
25
16
(
HV-
AC IN
AC OUT
12VDC
PV+
LED-
LED+
DISPLAY
HRLYCIB
S232
NTC2
NTC1
GVAL
87
85
86
30
8
-
+
D+
10
10
+
-
q
➤ Connect the device as follows:
RUA5208X
25
EN
Connecting the refrigerator RUA5208X, RUA6408X, RUA 8408X
1
2
5
4
3
67 8
12
11
9
10
13
14
17
21
20
22
24
19
18
23
26
27
25
16
15
(
HV-
AC IN
AC OUT
12VDC
PV+
LED-
LED+
DISPLAY
HRLYCIB
S232
NTC2
NTC1
GVAL
87
85
86
30
8
-
+
D+
10
10
+
-
r
RUA6208X, RUA8408X
26
EN
RUA5208X, RUA6408X, RUA 8408X Connecting the refrigerator
Item Description
1 Connection cable for AC connection
2 Heater 240 V AC
3 Earth for CU
4 Protective Earth
5 Electrode
6Outer fan 1
7 Fan thermostat
8Outer fan 2
9 Ignition port
10 Power module
11 Control button
12 Display
13 Inner fan
14 LAC and defrost heater
15 Frame heater (RUA6208X, RUA8408X only)
16 Gas valve
17 Temperature sensor
18 Lamp
19 Door sensor
20 Gas inlet
21 12 V DC heater
22 Relay
23 12 V DC vehicle battery connection
24 Thermostat
25 D+ to alternator connection
26 12 V DC house battery connection
27 Thermofuse
27
EN
Connecting the refrigerator RUA5208X, RUA6408X, RUA 8408X
AC power
➤ Connect the refrigerator with the mains plug to an AC socket.
DC power
Please note the following cable sizes:
– 12 V DC vehicle battery connection: ≥ 10 mm
– 12 V DC house battery connection: ≥ 1mm
– Connection D+: ≥ 0.5 mm
2
2
2
– Total cable length: max. 8 m
➤ Protect the DC power supply for the 12 V DC heater with 30 A fuse.
➤ Protect the DC power supply for controls with 3 A fuse.
➤ Run cables to the heating element via a relay or suitable means controlled by an
ignition switch to prevent battery from completely discharging, if the engine is
switched off (fig. p, page 24).
➤ Connect vehicle battery cables to the respective plus and minus terminal
(fig. q 23, page 25).
➤ Connect house battery cables to the respective plus and minus terminal
(fig. q 26, page 25).
D+
In automatic mode, the refrigerator selects the most favourable mode available. The
refrigerator is only operated with DC power when the vehicle engine is running. The
electronics of the refrigerator uses the signal D+ from the vehicle alternator to detect
the running engine.
➤ Connect the D+ connection to the controls (fig. q 25, page 25) with the
respective terminal of the vehicle.
28
EN
RUA5208X, RUA6408X, RUA 8408X Connecting the refrigerator
+-+-
House Battery
Anderson Plug
Anderson cables must be the
recommended size.
Refrigerator DC connections
D+ Control Element DC
DC B E F
s
+-+-
Vehicle Anderson plug must
be controlled by ignition relay.
House Battery
Anderson Plug
Anderson cables must be the
recommended size.
Refrigerator DC connections
D+ Control Element DC
DC B E F
t
7.3 Alternative connection methods for DC power supply
Connection to suit motor home or caravan with the D+ wire connected to the vehicle
alternator or ignition switch.
No house battery recharging from the vehicle.
The D+ connection is taken to the vehicle alternator.
Anderson plug controlled by vehicle relay to the ignition switch. Power can only be
supplied if the engine is running.
No house battery recharging from the vehicle.
29
EN
Connecting the refrigerator RUA5208X, RUA6408X, RUA 8408X
+-+-
Fridge
Switch
Vehicle Anderson plug must
be controlled by ignition relay.
House Battery
Anderson Plug
Anderson cables must be the
recommended size.
Refrigerator DC connections
D+ Control Element DC
DC B E F
u
v
Using a fridge movement switch to add 12 Vg to the D+ connection wire, only
when the vehicle is moving.
No house battery recharging from the vehicle.
The D+ is turned on and off via an optional fridge movement switch.
Refrigerator DC connections
D+ Control Element DC
DC B E F
+-+-
Fridge
Switch
Vehicle Anderson plug must
be controlled by ignition relay.
House Battery
Anderson Plug
Anderson cables must be the
recommended size.
Using a fridge movement switch to add 12 Vg to the D+ connection wire, only when
the vehicle is moving. The Anderson plug connection must keep the house battery
fully charged.
House battery recharged by vehicle.
The D+ is turned on and off via an optional fridge movement switch.
30
EN
RUA5208X, RUA6408X, RUA 8408X Connecting the refrigerator
+-+-
Vehicle Anderson plug must
be controlled by ignition relay.
House Battery
Anderson Plug
Anderson cables must be the
recommended size.
Refrigerator DC connections
D+ Control Element DC
DC B E F
w
Anderson plug recharging the house battery via a power diode. The D+ wire can
only get a 12 V signal when the battery is being charged.
House battery recharged by vehicle.
The D+ is turned on and off by the vehicle starting and stopping.
31
YOUR LOCAL
SALES OFFICE
dometicĶ ,*ű0)"0Ŗ,= "s
YOUR LOCAL
DEALER
dometic.com/dealer
YOUR LOCAL
SUPPORT
dometic.com/contact
dometic.com
*+-)"1")&01*#*+"1& *+-,&"0ķ4%& % *+-/&0"1%"*+"1& /*2-ķ ,"#*2,!&,1%"-2)& 9)&,$0*#ĸ
DOMETIC GROUP AB"+3E/,0$1,ĉčŖĉďĉčČ*),4"!",
4450019507 4445102445 570-MAW40B03 06/2019
Loading...