Dometic Oasis 976XX48.000 Series, Oasis 976XX56.000 Series, Oasis 976XX56.100 Series, Oasis 976 SERIES, Oasis 976XX48.100 Series Operating Instructions Manual
Page 1
RECORD THIS INFORMATION FOR FUTURE
REFERENCE:
Model Number
Serial Number
Date Purchased
Retailer / Qualied Installer
OASIS MANUAL
976 SERIES
RV DOOR
AWNING SYSTEM
976(XX)48.000(#)
976(XX)48.100(#)
976(XX)56.000(#)
976(XX)56.100(#)
INSTRUCTIONS
INSTALLATION & OPERATING
REVISION B
Form No. 3310434.034 09/16
(French 3310439.033_B)
©2016 Dometic Corporation
LaGrange, IN 46761
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
Read these instructions carefully. These
instructions MUST stay with this product.
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
Page 2
INTRODUCTION
The Oasis manual series door awning (hereinafter referred to as “door awning,” “awning,” or “product”) is designed and
intended for use on RVs with straight sides. It is designed for use over RV entry doors.
This awning can be installed by one person with brief help from additional personnel. Use these instructions to install the
awning, to ensure correct function of product, and to operate your awning safely and correctly. Keep these instructions with
your awning for future reference.
Dometic Corporation reserves the right to modify appearances and specications without notice.
TABLE OF CONTENTS
INTRODUCTION .................................................................................................................................................................... 2
DOCUMENT SYMBOLS ........................................................................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS ................................................................................................................................3
A. Recognize Safety Information ...................................................................................................................................3
B. Understand Signal Words ..........................................................................................................................................3
C. Supplemental Directives ............................................................................................................................................3
D. General Safety Messages .........................................................................................................................................3
GENERAL INFORMATION .....................................................................................................................................................4
A. Included Hardware ....................................................................................................................................................4
SPECIFICATIONS .................................................................................................................................................................. 4
A. Door Clearance .........................................................................................................................................................4
B. Awning Dimensions ...................................................................................................................................................4
INSTALLATION ......................................................................................................................................................................4
A. Determine Awning Location ....................................................................................................................................... 4
B. Install Awning Rail And Secure Awning .....................................................................................................................4
C. Secure Awning For Travel .........................................................................................................................................5
OPERATION ........................................................................................................................................................................... 6
A. Open Awning .............................................................................................................................................................6
B. Close Awning ............................................................................................................................................................. 6
C. Prepare Awning For Travel ........................................................................................................................................6
GENERAL CARE AND USE ...................................................................................................................................................7
A. Precautions ................................................................................................................................................................ 7
B. Hardware Maintenance .............................................................................................................................................7
C. Fabric Maintenance ...................................................................................................................................................7
D. When To Get More Help ............................................................................................................................................7
DOCUMENT SYMBOLS
Indicates additional information that is NOT related
to physical injury.
Indicates step-by-step instructions.
2
Page 3
IMPORTANT SAFETY INSTRUCTIONS
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.
A. Recognize Safety Information
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
B. Understand Signal Words
A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.
indicates a hazardous situation that,
if NOT avoided, could result in death or serious injury.
indicates a hazardous situation that,
if NOT avoided, could result in minor or moderate
injury.
is used to address practices NOT
related to physical injury.
C. Supplemental Directives
Read and follow all safety information and
instructions to avoid possible injury or death.
Read and understand these instructions before [installing / using / servicing / performing
maintenance on] this product.
Incorrect [installation / operation / servicing /
maintaining] of this product can lead to serious injury. Follow all instructions.
The installation MUST comply with all applicable local and national codes, including
the latest edition of the following standards:
U.S.A.
● ANSI/NFPA 1192, Recreational Vehicles
Code
CANADA
● CSA Z240 RV Series, Recreational
Vehicles
D. General Safety Messages
Failure to obey the following warnings could result in death or serious injury:
● This product MUST be [installed / serviced] by a
qualied service technician.
● Do NOT modify this product in any way. Modica-
tion can be extremely hazardous.
● Frequently examine product for imbalance (un-
even t / sagging / loose parts); and signs of wear
or damage to wiring (if applicable) and other critical parts. Do NOT use product if adjustments or
repairs are necessary.
Critical parts may include awning fabric,
cables, arm assemblies, etc.
● Disconnect product from power supply (if ap-
plicable), and do NOT operate product when
maintenance (such as window cleaning) is being
carried out in the vicinity.
● Do NOT allow anyone (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge to use this
product, unless they have been given supervision
or instruction (concerning use of this product) by
a person responsible for their safety.
● Do NOT allow children to play with product or with
xed controls (if applicable).
● Keep remote controls (if applicable) away from
children.
● IMPACT OR CRUSH HAZARD. NEVER leave an
open awning unattended. Keep awning stowed
(closed) when snow, heavy rain, wind, and severe
weather conditions are expected. Failure to obey
this warning could result in death or serious injury.
● IMPACT OR CRUSH HAZARD. Do NOT allow
water to pool, snow to accumulate, or heavy
debris on awning fabric. Do NOT hang or place
anything on awning. The awning will become unstable, and could bend or collapse. Failure to obey
this warning could result in death or serious injury.
● IMPACT OR CRUSH HAZARD. This product
should be installed in a controlled environment
(inside). Do NOT install product during windy
conditions, or when wind is expected. Otherwise,
product could move unpredictably, become unstable, and could [detach / bend / collapse].
● FIRE HAZARD. Keep sources of heat and re
(barbecue grills, portable heater, etc.) away from
awning. Failure to obey this warning could result
in death or serious injury.
PINCH HAZARD. Maintain a hori-
zontal distance of at least 16″ between fully open
awning and any permanent object. Failure to obey
this caution could result in injury.
Do NOT face awning toward permanent
objects that may interfere with awning operation.
3
Page 4
GENERAL INFORMATION
A. Included Hardware
(2) #10-16 X 5/8″ Self Drilling Screws
SPECIFICATIONS
A. Door Clearance
Maintain a minimum distance of 10 1/2″ between
awning rail and entry door. See (FIG. 1).
FIG. 1
Avoid
Interference
RV Door (Open)
Awning Rail
10 1/2″
(*) #6-20 X 1/2″ Square Drive Screw
*Quantity varies by length of awning rail.
B. Awning Dimensions
1. Awning overall dimensions. See (FIG. 2).
FIG. 2
A
B
C
INSTALLATION
A. Determine Awning Location
1. IMPACT OR CRUSH HAZARD.
Make sure mounting surface on RV is at, has
solid structural backing where fasteners penetrate surface, and will safely and securely support product. Otherwise, product may become
unstable and could [detach / bend / collapse].
Failure to obey this warning could result in death
or serious injury.
Find a solid structure in RV wall (centered over
door) for support of awning rail and back rail (all
mounting points).
2. Allow for sufcient clearance be-
tween awning fabric and entry door to accommodate awning pitch (slope).
Avoid location that interferes with entry door
swing when awning is completely extended. See
subsection, "A. Door Clearance" on page (4).
3. Maintain a minimum of 1/2″ clearance at top and
sides of awning case.
Additional clearance is recommended to
allow easier access for servicing.
Model A B C
976(XX)48.(X)00(#)
976(XX)56.(X)00(#)
50″ 6″ 4″
57″ 6″ 4″
B. Install Awning Rail And Secure Awning
1. Install awning rail on a at surface
(with solid structural backing), straight (without
curves), and parallel to RV oor to ensure correct function and appearance.
ALWAYS use sealant on (clean) parts and surfaces where fasteners enter RV’s [walls / roof /
oor]. Otherwise, water leakage could occur.
Apply sealant to the back edge of awning rail,
and to the #6-20 X 1/2″ screws (provided). Then
place and tighten screws through awning rail
and into solid structure of RV.
The awning rail is NOT provided with this
awning, but it may be ordered separately
from Dometic Corporation.
#6 X 1″ wood screws (installer supplied)
may be used if strength requirements are
met for the safe installation and operation
of this awning.
4
Page 5
INSTALLATION
2. Select the desired awning rail end (on RV) into
which the awning bracket will be inserted. Widen
that end of the rail with a at screwdriver, and le
off any sharp edges. See (FIG. 3).
FIG. 3
Before After
3. LIFTING HAZARD. Use proper
lifting technique and control when lifting product.
Failure to obey this caution could result in injury.
Carefully lift awning and align awning back rail’s
bracket to the prepared awning rail end. See
(FIG. 3) & (FIG. 4).
FIG. 4
Awning Rail
If bottom mounting holes are NOT already
present, drill (2) 9/64″ diameter holes
through back rail (approximately 1/2″
above bottom edge and 4″ from each end
of back rail).
Screws provided are self drilling/tapping,
so it is NOT necessary to drill through RV
wall.
FIG. 5
Approximate Location Of
Bottom Mounting Holes
4″ 4″
7. Secure awning with a #6 X 1/2″ TEK screw (installer supplied) on each end of awning rail (ap-
proximately 6″ from awning bracket edge). See
(FIG. 6).
1/2″
Bracket
(Awning
Back Rail)
Awning
Back Rail
4. Insert awning back rail’s bracket into awning rail
(a stepladder may be necessary), and carefully
move (slide) the awning until it is in desired position. See (FIG. 4).
Awning should be centered on awning rail.
To facilitate sliding along rail, awning may
be rotated up.
5. Fully open awning. See “Open Awning” in Operating Instructions.
6. Apply sealant to #10-16 X 5/8″ screws (provided). Then place and tighten screws through
back rail (bottom mounting holes) and into solid
structure of RV. See (FIG. 5).
FIG. 6
#6 X 1/2″
TEK Screw
Awning
Bracket
6″
C. Secure Awning For Travel
1. Operate awning according to Operating Instruc-
tions to verify all parts are functioning correctly.
2. Fully close awning. See “Close Awning” in Operating Instructions.
3. Verify awning is secure for travel. See “Prepare
Awning For Travel” in Operating Instructions.
5
Awning Rail
Page 6
OPERATION
A. Open Awning
PINCH HAZARD. Maintain a hori-
zontal distance of at least 16″ between fully open
awning and any permanent object. Failure to obey
this caution could result in injury.
1. Place hook end of hand crank into gear’s eye.
Then rotate hand crank (counter-clockwise) until
awning is fully extended. See (FIG. 7).
Awning is fully extended when fabric starts
to sag. See (FIG. 8).
FIG. 7
Gear’s Eye
Hand Crank
2. Do NOT allow awning fabric to
rest on arm assemblies. Wind will cause awning
fabric to rub against arm assemblies which could
result in premature wear and abrasions.
When awning is fully extended (fabric is sagging), rotate hand crank back (clockwise) approximately 1/4 turn to obtain maximum tension.
See (FIG. 7) & (FIG. 9).
Fabric edges MUST be taut.
FIG. 9
Fabric Edge
Lateral Arm
Assembly
FIG. 8
Fabric Edge
Taut Fabric
B. Close Awning
1. Place hook end of hand crank into gear’s eye.
Then rotate crank (clockwise) until awning is
fully retracted. See (FIG. 7).
C. Prepare Awning For Travel
1. With awning fully closed, verify awning is secure
for travel.
Look for loose parts, and any sign of instability.
Sagging Fabric
6
Page 7
GENERAL CARE AND USE
A. Precautions
Failure to obey the following notices
could damage product or property:
● Do NOT use insecticides or other sprays near aw-
ning fabric. These could cause stains, and could
adversely affect fabric’s ability to repel water.
● Do NOT expose awning to adverse environmental
conditions, corrosive agents, or other harmful
conditions.
● Do NOT allow corner of entry door to contact aw-
ning fabric. Otherwise, premature wear or tearing
of awning fabric could occur.
● NEVER close awning (for storage) when wet. The
combination of moisture and dirt could result in
mildew, discoloration, and stains.
If it is necessary to roll up awning (temporarily) while it’s wet, make sure you roll
it out and let it dry (as soon as conditions
allow) before rolling it up again.
● Do NOT allow dirt, leaves, or other debris to ac-
cumulate on awning, which could cause abrasion
and stains. Mildew could grow on dirt and organic
debris causing permanent discoloration, stains,
and odors to awning fabric.
B. Hardware Maintenance
1. Do NOT use strong chemicals or
abrasives to clean parts, as their protective surfaces will be damaged.
Clean awning hardware (as needed) with a mild
surface cleaner (such as dish soap).
2. Do NOT use silicone sprays near
labels. Otherwise, the label’s adhesive bond to
product surfaces could weaken.
Apply silicone spray lubricant as needed to keep
the fabric roller tube assembly’s moving parts
operating smoothly.
3. Lubricate all sliding surfaces of arm assemblies
with silicone spray as needed.
C. Fabric Maintenance
1. To clean:
a. Mix 1/4 cup dish soap and 1/4 cup bleach to
5 gallons of fresh water to use as cleaning
solution.
b. Do NOT use abrasive or cor-
rosive cleaners, mildew removers, or hard
bristle brushes on awning fabric.
Liberally drench open awning fabric with
cleaning solution.
c. Close awning, let it soak for 5 minutes, then
open awning again.
d. Remove solution COM-
PLETELY from awning fabric. Bleach will
degrade awning fabric if NOT completely
rinsed off.
Thoroughly hose off top and bottom of fabric
with clean water.
Repeat as necessary to completely remove solution.
e. NEVER close awning (for
storage) when wet. The combination of
moisture and dirt could result in mildew, discoloration, and stains.
Allow awning to dry thoroughly before stowing (rolling up).
2. To repair a pinhole, or if a spot of coating akes
off from top layer of vinyl fabric:
a. Apply a very small dab of VLP (Vinyl Liquid
Patch) on tip of cotton swab.
VLP is available from Dometic Corporation. Reference part number
3314216.000 when ordering.
b. Gently roll cotton swab around pinhole. The
VLP will melt the coating (on fabric) and that
will quickly ll in pinhole and blend with all
colored vinyls.
c. NEVER close (roll up) awning
when vinyl liquid patch is wet. Otherwise,
damage to other parts of awning fabric (melting through layers) will occur.
Allow VLP to dry thoroughly before stowing
(rolling up) awning.
Vinyl fabric offers the advantage of durability and
water resistance.
Wrinkling is a normal characteristic of vinyl.
Wrinkling may be more noticeable when retracted, and after prolonged periods of stowage (rolled up). Leave awning open during
warm weather to minimize the wrinkling over
a period of time.
D. When To Get More Help
If malfunctions occur (that cannot be corrected by
reviewing these instructions), contact a qualied
service technician.
7
Loading...