Please read this instruction manual carefully before first use, and store it in
a safe place. If you pass on the product to another person, hand over this
instruction manual along with it.
Safety instruction: Failure to observe this instruction will cause fatal or
serious injury.
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
!
NOTICE!
A
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
I
2Safety instructions
2.1General safety
WARNING!
•
Do not operate the product if it is visibly damaged.
!
•
If the power cable for this product is damaged, it must be replaced by
the manufacturer, customer service or a similarly qualified person in
order to prevent safety hazards.
•
This product may only be repaired by qualified personnel. Inadequate
repairs may cause serious hazards.
•
This product can be used by children aged 8 years or over, as well as
by persons with diminished physical, sensory or mental capacities or a
lack of experience and knowledge, providing they are supervised or
have been taught how to use the product safely and are aware of the
resulting risks.
11
EN
Safety instructionsTL, FO
•
Cleaning and user maintenance must not carried out by unsupervised
children.
•
Children should not play with the product.
•
Children must be supervised to ensure that they do not play with the
product.
•
Always keep and use the product out of the reach of children under
8 years of age.
•
Do not store any explosive substances, such as spray cans with
propellants, in the product.
CAUTION!
•
!
Disconnect the product from the mains
–Before cleaning and maintenance
–After use
•
Food may only be stored in its original packaging or in suitable
containers.
A
NOTICE!
•
Only connect the product as follows:
–with the DC connection cable to the vehicle battery
–or plug the AC connection cable into the AC socket
•
Check that the voltage specification on the type plate is the same as
that of the power supply.
•
Never pull the AC connection cable out of the AC socket by the cable.
•
The product is not suitable for storing substances which are caustic or
contain solvents.
•
Do not clean the product with a high-pressure cleaner. Exposure to
water can damage the product.
•
If the refrigerated container is connected to the battery: Disconnect
the refrigerated container and other power consuming devices from
the battery before connecting the quick charging device.
•
If the refrigerated container is connected to the battery: Disconnect
the cooler or switch it off when you turn off the engine. Otherwise the
battery may discharge.
12
EN
TL, FOIntended use
2.2Operating the product safely
DANGER!
Do not touch exposed cables with your bare hands. This applies espe-
D
!
A
cially when operating the product from the AC mains.
CAUTION!
Before starting the device, ensure that the power supply line and the plug
are dry.
NOTICE!
•
Do not use electrical devices inside the product unless they are recommended by the manufacturer for that purpose.
•
Do not place the product near naked flames or other heat sources
(heaters, direct sunlight, gas ovens etc.).
•
Danger of overheating!
Always ensure sufficient ventilation so that the heat generated during
operation can dissipate. Make sure that the product is sufficiently far
away from walls and other objects so that the air can circulate.
•
Ensure that the ventilation openings are not covered.
•
Protect the product and the cable against heat and moisture.
3Intended use
The TL200, TL450, TL600 refrigerated containers are ideal for refrigerating and
freezing food items at a constant temperature of +4 °C or –18 °C.
The FO200, FO450, FO600, FO800, FO1000 refrigerated containers are ideal for
refrigerating food items at a constant temperature of +4 °C.
The refrigerated containers are designed for operating with direct current (standard:
12 Vg; on request: 12/24 Vg) and alternating current versions.
The refrigerated container has a lock on the lid (not FO800, FO 1000) and a fastening
strap.
CAUTION! Health hazard!
!
Please check if the cooling capacity of the device is suitable for storing
the food you wish to cool or freeze.
13
EN
Scope of deliveryTL, FO
4Scope of delivery
DescriptionQuantity
Refrigerator container1
AC connection cable1
DC connection cable1
Key for temperature selection2
4.1Models (fig. 1, page 3, fig. 2, page 4)
ModelTemperature settingRef. no.
TL200+4 °C, –18 °C9103540405
TL450+4 °C, –18 °C9103540406
TL600+4 °C, –18 °C9103540407
FO200+4 °C9103540408
FO450+4 °C9103540409
FO600+4 °C9103540410
FO800+4 °C9600002642
FO1000+4 °C9600002641
5Accessories
Available as accessories (not included in the scope of delivery; not for FO800,
FO1000):
DescriptionQuantityRef. no.
Attachable rollers for 800 kg load49103540412
DT24 lead gel battery–9103540411
14
EN
TL, FOTechnical description
6Technical description
The refrigerated container can cool and freeze goods at a constant temperature of
+4 °C and –18 °C (TL200, TL450, TL600) or cool at +4 °C (FO200, FO450,
FO600, FO800, FO1000). A maintenance-free refrigerant circuit with compressor
provides the cooling.
Depending on the model, the refrigerated container can operate on a AC or DC
power supply.
The refrigerated container has a battery monitor which protects the vehicle battery
from excessive discharging:
•
Switch-on voltage = 12.3 V
•
Switch-off voltage = 11.7 V
6.1Connections and controls
No. in fig. 3, page 4Description
1DC power supply
2AC power supply
3On/off switch
No. in fig. 7, page 6Description
1Key switch for temperature selection
7Installing and connecting the
refrigerated container
➤ Observe the minimum clearances for the place of installation (fig. 4, page 5).
➤ Place the refrigerated container on a stable and even floor.
7.1Operating with AC power supply
➤ Plug the AC connection cable into the AC power supply connection (fig. 3 2,
page 4).
➤ Connect the refrigerated container to the AC power supply.
15
EN
Installing and connecting the refrigerated containerTL, FO
7.2Operating with DC power supply
NOTICE! Risk of damage to the device!
A
For safety reasons, the refrigerated container is equipped with an electronic system
to prevent the polarity being reversed. This protects it against reversed polarity when
connecting to a battery and against short circuiting.
A
Disconnect the refrigerated container and other electric consumers
from the battery before you connect the battery to a quick charging
device.
Overvoltage can damage the electronics of the device.
NOTICE! Risk of damage to the device!
To avoid voltage drops and loss of performance, keep the cable as short
as possible and avoid joins.
Therefore avoid additional switches, plugs or power strips.
➤ Determine the required cross section of the cable in relation to the cable length
according to fig. 5, page 5.
Key for fig. 5, page 5
Coordinate axisMeaningUnit
lCable lengthm
∅Cable cross sectionmm²
NOTICE! Risk of damage to the device!
Make sure that the polarity is correct.
A
➤ Before starting up the device for the first time, check whether the operating
voltage and the battery voltage match (see type plate).
➤ Make sure that the cable at the positive battery terminal (fig. 6 1, page 6) is pro-
tected with a 25 A fuse (fig. 6 3, page 6).
➤ Plug the DC connection cable into the DC socket of the refrigerated container
(fig. 3 1, page 4).
16
EN
TL, FOOperating the refrigerated container
➤ Connect the red cable (fig. 6 rd, page 6) to the positive terminal of the battery
(fig. 6 1, page 6).
➤ Connect the black cable (fig. 6 blk, page 6) to the negative terminal of the
battery (fig. 6 2, page 6).
Notes on the battery monitor
The product is equipped with a battery monitor that protects your vehicle battery
against excessive discharging when the device is connected to the on-board supply.
If the refrigerated container is operated when the vehicle ignition is switched off, it
switches off automatically as soon as the supply voltage falls below a settable level.
The refrigerated container will switch back on once the battery has been recharged
to the restart voltage level.
NOTICE! Risk of damage!
A
When switched off by the battery monitor, the battery will no longer be
fully charged. Avoid starting repeatedly or operating electric consumers
without longer charging phases. Make sure that the battery is
recharged.
8Operating the refrigerated container
CAUTION! Health hazard!
!
I
8.1Storing food items
I
Food may only be stored in its original packaging or in suitable
containers.
NOTE
•
The key in the key switch for temperature selection can be removed
in any position. The container continues to refrigerate.
•
Before starting your refrigerated container for the first time, you
should clean it inside and outside with a damp cloth for hygienic
reasons (see also chapter “Cleaning and maintenance” on page 19).
NOTE
At a temperature setting of –18 °C: Only put goods in the refriger-
ated container which are already frozen at –20 °C. The refrigerated container is not suitable for freezing.
17
EN
Operating the refrigerated containerTL, FO
8.2Energy saving tips
•
Choose a well ventilated position which is protected from direct sunlight.
•
Allow warm food to cool down first before placing it in the product to freeze.
•
Do not open the refrigerated container more often than necessary.
•
Do not leave the refrigerated container open for longer than necessary.
•
Defrost the refrigerated container once a layer of ice forms.
8.3Selecting the temperature (for TL200, TL450, TL600
only)
➤ Turn the key switch to the required position (fig. 7, page 6).
➤ Remove the key and store in a safe place.
8.4Switching on the refrigerated container
NOTICE! Risk of damage!
•
A
➤ Set the on/off switch (fig. 3 3, page 4) to the “I” position.
➤ Insert the key into the key switch.
➤ Turn the key to the required temperature.
✓ The compressor switches on and the refrigerated container starts to cool.
Only put food items in the refrigerated container which may be kept
at the selected temperature.
•
Ensure that your refrigerated container is well ventilated so that any
heat created can dissipate. Otherwise proper functioning cannot be
ensured. The air vents may not be covered up.
8.5Mounting the rollers (accessory)
Not for FO800, FO1000
You can fit block rollers or casters instead of the stands:
➤ Remove the four stands and screw on the four block rollers or casters into the
same position (fig. 8, page 7).
18
EN
TL, FOCleaning and maintenance
8.6Using the lock for the lid
Not for FO800, FO1000
➤ Close the sliding doors on both sides.
➤ Slide the catch into the inlet provided so that it clicks into position (fig. 9 1,
➤ Remove the layer of ice at a thickness of 2 mm using a plastic scraper.
➤ Defrost the refrigerated container.
➤ Remove the thawed water.
NOTE
I
TL200, TL450, TL600: The refrigerated container has an opening on
the back that you can connect a drain hose to for draining the condensate.
FO800, FO1000: The refrigerated container has a drain hose on the
back for draining condensate.
9Cleaning and maintenance
NOTICE! Risk of damage!
A
➤ Occasionally clean the refrigerated container interior and exterior with a damp
cloth.
➤ Remove the base plates occasionally and clean these with a damp cloth.
➤ Make sure that the air vents on the refrigerated container are free of any dust and
dirt, so that heat can be released and the refrigerated container is not damaged.
Do not use abrasive cleaning agents or hard objects during cleaning as
these can damage the refrigerated container.
19
EN
TroubleshootingTL, FO
10Troubleshooting
FaultPossible causeSuggested remedy
The refrigerated container
does not work.
The refrigerated container
does not freeze properly
(for TL200, TL450, TL600
only).
The refrigerated container
does not cool sufficiently.
The refrigerated container is
not correctly connected.
The temperature key is not
set to the required temperature.
The goods placed in the
refrigerated container are
too warm.
The air vents are dusty or
dirty.
The ventilation around the
refrigerated container is not
sufficient.
The set temperature is
+4 °C.
The goods placed in the
refrigerated container are
too warm.
Check the voltage supply.
Turn the temperature key to the
required temperature.
Only put goods in the refrigerated container which are cold
at –20 °C.
Remove the dust and dirt from
the air inlet and outlet vents.
Ensure a sufficient circulation of
air around the air vents.
Adjust the temperature to
–18 °C.
Only put goods in the refrigerated container which are
already cold.
The air vents are dusty or
dirty.
The ventilation around the
refrigerated container is not
sufficient.
Remove the dust and dirt from
the air inlet and outlet vents.
Ensure a sufficient circulation of
air around the air vents.
20
EN
TL, FOTechnical data
11Technical data
TL200TL450TL600
Ref. no.:910354040591035404069103540407
Adjustable temperature:
Climatic class:ST
Connection voltage: 12 Vg
Coolant:R134aR404aR404a
Coolant quantity:150 g245 g280 g
CO2 equivalent:0.588 t0.961 t1.098 t
Global warming
potential (GWP):
Net capacity:209 l435 l590 l
Dimensions: see fig. 0, page 8
+4 °C, –18 °C
24 Vg (on request)
230 Vw
1430
21
EN
Technical dataTL, FO
FO200FO450FO600
Ref. no.:910354040891035404099103540410
Adjustable tempera-
+4 °C
ture:
Climatic class:ST
Connection voltage: 12 Vg
24 Vg (on request)
230 Vw
Coolant:R134aR134aR134a
Coolant quantity:150 g245 g280 g
equivalent:0.215 t0.350 t0.400 t
CO
2
Global warming
1430
potential (GWP):
Net capacity:209 l435 l590 l
Dimensions: see fig. 0, page 8
FO800FO1000
Ref. no.:96000026429600002641
Adjustable tempera-
+4 °C
ture:
Climatic class:ST
Connection voltage: 12 Vg
24 Vg (on request)
230 Vw
Coolant:R404a
Coolant quantity:155 g
equivalent:0.608 t
CO
2
Global warming
3922
potential (GWP):
Net capacity:825 l963 l
Dimensions: see fig. a, page 9
22
EN
TL, FOTechnical data
Contains fluorinated greenhouse gases
Hermetically sealed equipment
For the current EU declaration of conformity for your device please refer to the
respective product page on dometic.com or contact the manufacturer directly (see
back page).
23
DE
TL, FO
Bitte lesen Sie diese Anleitung vor der Inbetriebnahme sorgfältig durch
und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des
Produktes an den Nutzer weiter.
Sicherheitshinweis: Nichtbeachtung führt zu Tod oder schwerer
Verletzung.
WARNUNG!
Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer
Verletzung führen.
VORSICHT!
Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.
!
ACHTUNG!
A
Nichtbeachtung kann zu Materialschäden führen und die Funktion des
Produktes beeinträchtigen.
HINWEIS
Ergänzende Informationen zur Bedienung des Produktes.
I
2Sicherheitshinweise
2.1Allgemeine Sicherheit
WARNUNG!
•
!
Wenn das Produkt sichtbare Beschädigungen aufweist, dürfen Sie es
nicht in Betrieb nehmen.
•
Wenn das Anschlusskabel dieses Produktes beschädigt wird, muss es
durch den Hersteller, seinen Kundendienst oder eine ähnlich qualifizierte Person ersetzt werden, um Gefährdungen zu vermeiden.
•
Reparaturen an diesem Produkt dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche
Gefahren entstehen.
25
DE
SicherheitshinweiseTL, FO
•
Dieses Produkt kann von Kindern ab 8 Jahren und darüber sowie von
Personen mit verringerten physischen, sensorischen oder mentalen
Fähigkeiten oder Mangel an Erfahrung und Wissen benutzt werden,
wenn sie beaufsichtigt oder bezüglich des sicheren Gebrauchs des
Produktes unterwiesen wurden und die daraus resultierenden Gefahren verstehen.
•
Reinigung und Benutzer-Wartung dürfen nicht von Kindern ohne
Beaufsichtigung durchgeführt werden.
•
Kinder dürfen nicht mit dem Produkt spielen.
•
Kinder sollten beaufsichtigt werden, um sicherzustellen, dass sie nicht
mit dem Produkt spielen.
•
Verwahren und benutzen Sie das Produkt außerhalb der Reichweite
von Kindern unter 8 Jahren.
•
Lagern Sie keine explosionsfähigen Stoffe wie z. B. Sprühdosen mit
brennbarem Treibgas im Produkt.
!
A
VORSICHT!
•
Trennen Sie das Produkt vom Netz
–vor jeder Reinigung und Pflege
–nach jedem Gebrauch
•
Lebensmittel dürfen nur in Originalverpackungen oder geeigneten
Behältern eingelagert werden.
ACHTUNG!
•
Schließen Sie das Produkt nur wie folgt an:
–mit dem Gleichstrom-Anschlusskabel an die Fahrzeugbatterie
–oder mit dem Wechselstrom-Anschlusskabel an die Wechsel-
stromsteckdose.
•
Vergleichen Sie die Spannungsangabe auf dem Typenschild mit der
vorhandenen Energieversorgung.
•
Ziehen Sie den Stecker nie am Wechselstrom-Anschlusskabel aus der
Wechselstromsteckdose.
•
Das Produkt ist nicht geeignet für die Lagerung ätzender oder
lösungsmittelhaltiger Stoffe.
•
Reinigen Sie das Produkt nicht mit einem Hochdruckreiniger.
Eindringendes Wasser kann das Produkt beschädigen.
•
Wenn das Kühlgerät an der Batterie angeschlossen ist: Klemmen Sie
Ihr Kühlgerät und andere Verbraucher von der Batterie ab, bevor Sie
ein Schnellladegerät anschließen.
26
DE
TL, FOSicherheitshinweise
•
Wenn das Kühlgerät an der Batterie angeschlossen ist: Trennen Sie die
Verbindung oder schalten Sie das Kühlgerät aus, wenn Sie den Motor
ausschalten. Sonst kann die Batterie entladen werden.
2.2Sicherheit beim Betrieb des Produktes
GEFAHR!
Fassen Sie nie mit bloßen Händen an blanke Leitungen. Dies gilt vor allem
D
!
A
beim Betrieb am Wechselstromnetz.
VORSICHT!
Achten Sie vor der Inbetriebnahme darauf, dass Zuleitung und Stecker
trocken sind.
ACHTUNG!
•
Benutzen Sie keine Elektrogeräte innerhalb des Produktes, außer
wenn diese Elektrogeräte vom Hersteller dafür empfohlen werden.
•
Stellen Sie das Produkt nicht in der Nähe von offenen Flammen oder
anderen Wärmequellen (Heizung, starke Sonneneinstrahlung,
Gasöfen usw.) ab.
•
Überhitzungsgefahr!
Achten Sie stets darauf, dass beim Betrieb entstehende Wärme ausreichend abgeführt werden kann. Sorgen Sie dafür, dass das Produkt
in ausreichendem Abstand zu Wänden oder Gegenständen steht,
sodass die Luft zirkulieren kann.
•
Achten Sie darauf, dass die Lüftungsöffnungen nicht abgedeckt
werden.
•
Schützen Sie das Produkt und die Kabel vor Hitze und Nässe.
27
DE
Bestimmungsgemäßer GebrauchTL, FO
3Bestimmungsgemäßer Gebrauch
Die Kühlcontainer TL200, TL450, TL600 eignen sich zum Kühlen und Tiefkühlen von
Lebensmitteln bei einer konstanten Temperatur von +4 °C oder –18 °C.
Die Kühlcontainer FO200, FO450, FO600, FO800, FO1000 eignen sich zum
Kühlen von Lebensmitteln bei einer konstanten Temperatur von +4 °C.
Die Kühlcontainer sind für den Betrieb an Gleichstrom (Standard: 12 Vg; auf
Anfrage: 12/24 Vg) und Wechselstrom ausgelegt.
Der Kühlcontainer verfügt über eine Deckelsicherung (nicht FO800, FO1000) und
einen Spanngurthalter.
VORSICHT! Gesundheitsgefahr!
!
Prüfen Sie bitte, ob die Kühlleistung des Gerätes den Anforderungen
der Lebensmittel entspricht, die Sie kühlen oder tiefkühlen wollen.
4Lieferumfang
BezeichnungMenge
Kühlcontainer1
Wechselstrom-Anschlusskabel1
Gleichstrom-Anschlusskabel1
Schlüssel für Temperaturwahl2
28
DE
TL, FOZubehör
4.1Modelle (Abb. 1, Seite 3, Abb. 2, Seite 4)
ModellTemperatureinstellungArt.-Nr.
TL200+4 °C, –18 °C9103540405
TL450+4 °C, –18 °C9103540406
TL600+4 °C, –18 °C9103540407
FO200+4 °C9103540408
FO450+4 °C9103540409
FO600+4 °C9103540410
FO800+4 °C9600002642
FO1000+4 °C9600002641
5Zubehör
Als Zubehör erhältlich (nicht im Lieferumfang enthalten; nicht für FO800, FO1000):
BezeichnungMengeArt.-Nr.
Anbaurollen für 800 kg Last49103540412
Blei-Gel-Batterie DT24–9103540411
6Technische Beschreibung
Der Kühlcontainer kann Waren bei einer konstanten Temperatur von +4 °C und
–18 °C (TL200, TL450, TL600) kühlen und tiefgekühlt halten oder bei +4 °C
(FO200, FO450, FO600, FO800, FO1000) kühlen. Die Kühlung erfolgt durch
einen wartungsfreien Kühlkreislauf mit Kompressor.
Der Kühlcontainer kann je nach Modell am Wechselstromnetz oder am Gleichstromnetz betrieben werden.
Der Kühlcontainer verfügt über einen Batteriewächter, der die Fahrzeugbatterie vor
zu tiefer Entladung schützt:
•
Einschaltspannung = 12,3 V
•
Ausschaltspannung = 11,7 V
29
DE
Kühlcontainer aufstellen und anschließenTL, FO
6.1Anschlüsse und Bedienelemente
Pos. in Abb. 3, Seite 4Bezeichnung
1Gleichstromanschluss
2Wechselstromanschluss
3Ein-/Ausschalter
Pos. in Abb. 7, Seite 6Bezeichnung
1Schlüsselschalter zur Temperaturwahl
7Kühlcontainer aufstellen und
anschließen
➤ Beachten Sie die Mindestabstände für den Aufstellort (Abb. 4, Seite 5).
➤ Stellen Sie den Kühlcontainer auf einen stabilen und ebenen Boden.
7.1Betrieb mit Wechselstrom
➤ Stecken Sie das Wechselstrom-Anschlusskabel in den Wechselstromanschluss
(Abb. 3 2, Seite 4).
➤ Schließen Sie den Kühlcontainer an das Wechselstromnetz an.
7.2Betrieb mit Gleichstrom
ACHTUNG! Gefahr von Geräteschäden!
A
Zur Sicherheit ist der Kühlcontainer mit einem elektronischen Verpolungsschutz ausgestattet, der den Kühlcontainer gegen Verpolung beim Batterieanschluss und
gegen Kurzschluss schützt.
Klemmen Sie den Kühlcontainer und andere Verbraucher von der
Batterie ab, bevor Sie die Batterie mit einem Schnellladegerät aufladen.
Überspannungen können die Elektronik der Geräte beschädigen.
30
Loading...
+ 210 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.