Dometic Cabana Lightweight RV Dome Awning, 747GRN11.000, 747GRN09.000, 747GRN13.000, 747GRN07.000 Installation And Operation Instructions Manual
Page 1
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
RECORD THIS UNIT INFORMATION FOR
FUTURE REFERENCE:
Model Number ____________________
Serial Number ____________________
Date Purchased ____________________
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
This manual must be read and
understood before installation,
adjustment, service, or maintenance is performed. This unit must
be installed by a qualied service
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
technician. Modification of this
product can be extremely hazardous and could result in personal
injury or property damage.
INSTALLATION &
OPERATION INSTRUCTIONS
Lire et comprendre ce manuel avant
de procéder à l'installation, à des réglages, de l'entretien ou des réparations. L'installation de cet appareil doit
être effectuée par un réparateur quali-
é. Toute modication de cet appareil
peut être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.
Model
747XXX07.000
747XXX09.000
747XXX11.000
747XXX13.000
REVISION A
Form No. 3312822.004 09/16
©2016 Dometic Corporation
LaGrange, IN 46761 U.S.A.
Important: These Instructions
must stay with unit.
Owner read carefully.
Page 2
SAFETY INSTRUCTIONS
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
This manual has safety information and instructions to help users eliminate or reduce the risk
of accidents and injuries.
RECOGNIZE SAFETY INFORMATION
This is the safety-alert symbol. When you see this
symbol in this manual, be alert to the potential
for personal injury.
Follow recommended precautions and safe operating instructions.
UNDERSTAND SIGNAL WORDS
(DIM "A")
(93")
(120")
Model Awning
Size
747GRN07.000 7' 81" 625
747GRN09.000 9' 105" 710
747GRN11.000 11' 129" 796
747GRN13.000 13' 153" 881
Dim A
(Width)
(96")
Approx.
Cubic FT
(105")
A signal word , WARNING OR CAUTION is used
with the safety-alert symbol. They give the level
of risk for potential injury.
indicates a potentially hazard-
ous situation which, if not avoided, could result
in death or serious injury.
indicates a potentially hazard-
ous situation which, if not avoided, may result in
minor or moderate injury.
used without the safety alert
symbol indicates, a potentially hazardous situation which, if not avoided, may result in property
damage.
Read and follow all safety information and instructions.
General Information
APPLICATION:
The Cabana Lightweight RV Dome Awning™ is designed to t most pop-up campers, allowing users
to nearly double their current living space. In order to nd the best size Dome Awning to use with
your particular pop-up camper, measure the size of
the awning rail on your camper. Choose one of the
four Cabana Lightweight RV Dome Awning™ sizes to
match the length of your awning rail: 7’, 9’, 11’ or 13’.
If your awning rail does not match any of these 4 sizes exactly, choose the next shortest size available.
For example, if your awning rail is 12’, an 11’ Dome
Awning would provide the best t on your camper.
Product features and specications as described
or illustrated are subject to change without notice.
Installation methods not described in this manual must
have written approval from Dometic Corporation.
Important: Read the entire Installation and Operating
Instructions carefully before starting the installation.
2
Page 3
CONTENTS:
Bag Awning/Room
(1) Flex Pole (collapsible)
(16) Snap Fast Fasteners
(3) Roof Poles (adjustable)
(25) Tent Stakes
(2) Hold Down Webbing Straps
Mesh Vehicle Skirt
Mesh Wheel Well Skirt
Roof Poles
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
3. Unzip bag & undo ties to roll fabric assembly out.
Unrolled fabric assembly
Flex Poles
Tent Stakes
Snap Fast Fasteners
TOOLS REQUIRED:
Power Drill/Screwdriver
Silicone spray/Lubricant
A. Slide Bag Into Standard Awning Rail
1. Spray inside of awning rail with silicone spray
or lubricant to ease sliding bag through
awning rail. Make sure Dometic logo faces away
from camper.
2. If the awning is to be left mounted during travel,
secure each end by installing a #6 X 1/2" (included) drill point screw in each end.
B. Assemble Poles and Dome Awning: Flex
Collapsible Pole (1) & Telescoping Aluminum Poles (3)
1. Assemble collapsible ex pole. Prepare Dome
Awning for ex pole by unzipping front panel from
the bottom up. Stop approximately at the buck-
les. Insert ex pole into sewn-in pocket located
on front of Dome Awning. Push ex pole through
entire front pocket.
Note: Do not try to pull ex pole through. Pulling will only
disassemble sections of the ex pole.
6X1/2"
Screw
Awning Rail
Edge Of
Awning Rail
3
Page 4
When ex pole is pushed through entire front
pocket, secure 1 pole end into brass grommet in
webbing.
Brass Grommet
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
2. Form arch with ex pole & insert other end
of ex pole into brass grommet on webbing.
Erect arch and with someone’s help, hold in place
while telescoping aluminum roof poles are installed inside Dome Awning.
3. Open lock on Clenchlock Lever System of telescoping aluminum roof poles.
Brass Grommet
Buckle webbing strap on opposite side.
OPEN LOCK POSITION
4. Insert ball end into ball end socket built into rear
ap of bag assembly against camper wall as
shown.
4
Page 5
5. Hook opposite end of telescoping pole onto front
ex pole thru opening in fabric assembly. This operation is easier to do from outside of Dome Awning or with help from outside of Dome Awning.
6. Extend telescoping pole to stretch roof fabric out and lock Clenchlock Lever in place.
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
C. Seal Dome Awning & Install Skirts
1. Straighten out fabric and fold bottom aps towards
outside.
2. Once Dome Awning is in place, install snap fast
fasteners where side wall aps meet camper.
This provides a seal between tent room and
camper.
LOCKED POSITION
Repeat above step with remaining 2 telescoping
poles.
3. Roll aps w/Velcro around camper extender
arms.
4. Install Wheel Well Skirt over wheel well
by marking grommet points at desired
height and drilling pilot holes then installing
snap fast fasteners.
5. Mark grommet points and drill pilot holes to
install snap fast fasteners for Vehicle Skirt.
Measure and install Vehicle Skirt across entire
vehicle. Cut excess skirt if necessary.
5
Page 6
D. Operating Tips
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
1. Side door can be rolled up & tied for convenient
entry & exit or it can be zipped shut for privacy
and help prevent ying insects from entering.
2. Privacy panels on Dome Awning can be rolled up &
tied in place with sewn-in ties to allow for air circulation
and visibility.
3. Dome Awning can also be used as breezeway by
unzipping & rolling up both sides.
Tie Down Strap Buckle
4. To use Dome Awning as a porch, unzip & roll up
both sides and remove entire front panel.
To remove front panel, unzip panels from the top
center down.
5. Optional hold down straps are included with the
Cabana Lightweight RV Dome Awning™ in case
additional stability is required in windy conditions.
Buckle one end to mating buckle attached to top
of side panel on Dome Awning. Secure opposite
end of strap to ground with tent stake.
Elastic cord loops at the hem of Dome Awning
provide extra stability when staked to ground with
included tent stakes.
Elastic Cord Loops
E. Cabana Lightweight RV Dome Awning™
Storage
Note: If Dome Awning is put away when condi-
tions are wet, it should be set up and allowed to dry
dry as soon as possible to prevent mold and mildew.
1. Remove tent stakes, if any were installed, from
hem and from hold down straps.
2. Unroll privacy panels and door and zip front panel, if it was previously removed. Leave front panel
unzipped from bottom to buckle location.
6
Page 7
3. Remove Vehicle Skirt and Wheel Well Skirt from
camper. Skirts can be folded and stored in the
Dome Awning bag. Fasteners may be left on the
camper for next time you use your Dome Awning.
4. Lower camper extender arms, if possible, as low
as possible to allow for better reach to Dome
Awning poles and bag or use a step stool.
5. Remove telescoping poles one at a time by unlocking Clenchlock lever then unhooking from front
ex pole then pulling opposite end of pole from
ball end base on bag. Set poles aside as they will
be stored in the bag with the rest of the Dome
Awning and Skirts.
6. Remove ex pole from pocket on Dome Awning
front by rst unbuckling webbing strap on bottom
front.
Pull ends of ex pole out of brass grommet on webbing
strap, one side at a time. Now you are ready to push
ex pole through pocket. DO NOT TRY
TO PULL FLEX POLE THROUGH
POCKET. Collapse ex pole and
set aside with telescoping poles for storage in
Dome Awning bag.
7. Now that you have the Dome Awning fabric assembly hanging without poles, fold in side panels
of fabric towards the center of the fabric assembly so as to try to make a square. “Square” fabric
assembly should not extend beyond the width of
the bag itself.
Cabana Lightweight RV Dome Awning™ Installation and Operation Instructions
8. Place all poles at the end of the fabric assembly
farthest away from the camper and begin rolling up
towards camper as tightly and neatly as possible.
This process is best done with two persons.
9. Once the entire Dome Awning assembly is rolled
up, fasten with ties sewn inside bag (3).
10. Zip Dome Awning bag closed. Insert Skirts
and bagged tent stakes into bag as well.
TO REDUCE THE RISK OF DEATH, PERSONAL IN-
JURY, FIRE OR DAMAGE:
1. Do not use grills, hibachis, camp stove or gas
burning lamps inside the Cabana Lightweight RV
Dome Awning™.
2. Never operate generators, motorcycles, any internal combustion engines inside the Cabana
Lightweight RV Dome Awning™.
3. Close attention is necessary when used by or
near children. Do not allow children or adults
to lean against the sides or front of the Cabana
Lightweight RV Dome Awning™.
4. Do not suspend electrical lights from rafter poles
or allow them to come in contact with the fabric
Cabana Lightweight RV Dome Awning™.
5. Do not modify or change the installation of this
Cabana Lightweight RV Dome Awning™.
6. Use only as described in this manual.
7
Page 8
LIMITED ONE (1) YEAR WARRANTY
THE SELLER NAMED BELOW MAKES THE FOLLOWING WARRANTY WITH
RESPECT TO THE DOMETIC PRODUCT:
1. This Warranty is made only to the rst purchaser (hereinafter referred to as the “Original Purchaser”) who acquires the product for his own use
and is installed and operated within the continental United States and Canada.
2. This Warranty will be in effect for one (1) year from the date of purchase by the original purchaser. It is suggested that the original purchaser
retain a copy of the dated bill of sale as evidence of the date of purchase.
3. This Warranty covers only specied parts which shall be free from defects in material and workmanship under normal use. This warranty does
NOT cover conditions unrelated to the material and workmanship of the product. Such unrelated conditions include, but are not limited to: (a)
damage not reported within seven (7) days of ownership; (b) failure or damage caused by storms, rain, water pooling, or any acts of God; (c)
faulty installation and any damage resulting from such; (d) the need for normal maintenance and any damage resulting from the failure to
provide such maintenance; (e) failure to follow Sellers instructions for use of this product; (f) any accident to or misuse of any part of this product
and any alteration by anyone other than the Seller or its authorized representative; (g) damage or failure caused by installation of accessories
not manufactured and marketed by the Seller; and (h) normal wear and product abuse.
4. The specied parts covered by this warranty, where applicable, are as follows: (a) Roller tube against rust, corrosion and extrusion defects; (b)
5. In order to obtain the benets of this warranty, you should return the product which you nd defective to the Seller named below or to a Dometic
6. Any item returned in the manner described in paragraph 5 will be examined by the Seller or the Authorized Dometic Service Center. If it is found
Fabric free from quality defects (normal wear is not covered); (c) Screen assemblies free from quality defects (normal wear is not covered); (d)
Torsion assemblies, including motor-driven assemblies, against extrusion defects, electrical faults, or breakage; and (d) Hardware against extrusion defects.
Authorized Service Center during the period that this warranty is in effect. The original owner is responsible for all charges incurred in delivery
of the product to the Seller, or Dometic Authorized Service Center, and in pick up after the warranty service has been completed. To obtain the
location of the nearest Authorized Service Center, please call 1-800-544-4881. In Canada, call 1-519-720-9578.
that the returned item was defective in material and workmanship, the Seller or the Authorized Dometic Service Center will repair the product
per the terms of this one (1) year limited warranty without charge for material or labor during the rst year of ownership by the original purchaser.
CONFIRM THE SERVICE AGENCY IS AN AUTHORIZED DOMETIC SERVICE CENTER. DO NOT PAY THE SERVICE AGENCY FOR WARRANTY REPAIRS. SUCH PAYMENTS WILL NOT BE REIMBURSED.
7. Dometic Corporation will pay freight on replacement parts during the rst ninety (90) days of ownership by the original purchaser.
8. The Seller does not authorize any person or company to create any warranty obligations or liability on their behalf. This warranty is not extended
by the length of time which you are deprived of the use of the product. Repairs and replacement parts provided under the terms of this warranty
shall carry only the non-expired portion of this warranty.
9. In no event shall either Seller be liable for incidental or consequential damages. This includes any damage to another product or products resulting from such a defect. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may
not apply.
10. Any implied warranty, including the implied warranty of merchantability and tness for any purpose, is limited to the duration of this limited warranty. Some states do not allow limitations on how long an implied warranty can last, so the above limitation may not apply.
11. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
No action to enforce this warranty shall be commenced later than ninety (90) days after the expiration of the warranty period. Claims must be
submitted in writing to the Dometic Warranty Department for arbitration.
12 All products (except those specically built for commercial use) are warranted only when installed on vehicles built to R.V.I.A. and C.R.V.A., Z-240
Standards.
13. The Seller reserves the right to change the design of any product without notice and with no obligation to make corresponding changes in products
previously manufactured.
DOMETIC CORPORATION
Warranty Department
1120 North Main Street
Elkhart, Indiana 46514
Loading...