Dometic 9500 200 003 Series, 9500 Series Installation Instructions Manual

RECORD THIS INFORMATION FOR FUTURE
REFERENCE:

Model Number
Serial Number
Date Purchased

Retailer / Qualied Installer

TYPE

9500

INSTALLATION

INSTRUCTIONS

MANUAL

CASE / CASSETTE AWNING

MODEL

200(LL)(CC).003(#)

REVISION D

Form No. 3314492.000 09/16
(French 3314493.000_D)
©2016 Dometic Corporation
LaGrange, IN 46761

Read these instructions carefully. These
instructions MUST stay with this product.

USA

SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514

CANADA

Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA

SERVICE CENTER &
DEALER LOCATIONS
Please Visit:

www.eDometic.com

INTRODUCTION

This case awning (hereinafter referred to as “awning,” or “product”) is designed and intended for use on RVs with straight
sides. It is especially well suited for RVs with an over cab extension where there is not sufcient surface for a bottom mount­ing bracket. This product can be installed by one person with brief help from additional personnel. Use these instructions to
ensure correct installation and function of product.

Dometic Corporation reserves the right to modify appearances and specications without notice.

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................................... 2

DOCUMENT SYMBOLS ........................................................................................................................................................2

IMPORTANT SAFETY INSTRUCTIONS ................................................................................................................................3

A. Recognize Safety Information ...................................................................................................................................3

B. Understand Signal Words ..........................................................................................................................................3

C. Supplemental Directives ............................................................................................................................................3

D. General Safety Messages .........................................................................................................................................3

GENERAL INFORMATION .....................................................................................................................................................3

A. Required Tools ...........................................................................................................................................................3

B. Required Hardware ...................................................................................................................................................3

C. Additional Hardware Quantity ....................................................................................................................................3

SPECIFICATIONS .................................................................................................................................................................. 4

A. Door Clearance .........................................................................................................................................................4

B. Awning Dimensions ...................................................................................................................................................4

INSTALLATION ......................................................................................................................................................................5

A. Determine Awning Location ....................................................................................................................................... 5

B. Install Mounting Bracket ............................................................................................................................................6

C. Install Awning .............................................................................................................................................................7

ADJUSTMENTS (OPTIONAL) ...............................................................................................................................................8

A. Adjust Fabric Slope (If Desired) .................................................................................................................................8

B. Adjust Lateral Arm Assemblies (If Required) .............................................................................................................8

C. Adjust Lead Rail Alignment (If Required) .................................................................................................................10

VERIFY INSTALLATION.......................................................................................................................................................10

A. Test Operation .........................................................................................................................................................10

B. Secure Awning For Travel .......................................................................................................................................10

C. Keep Literature ........................................................................................................................................................10

DOCUMENT SYMBOLS

Indicates additional information that is NOT related
to physical injury.

Indicates step-by-step instructions.

2

IMPORTANT SAFETY INSTRUCTIONS

This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.

A. Recognize Safety Information

This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.

B. Understand Signal Words

A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.

 indicates a hazardous situation that,
if NOT avoided, could result in death or serious in­jury.

 indicates a hazardous situation that,
if NOT avoided, could result in minor or moderate
injury.

 is used to address practices NOT
related to physical injury.

C. Supplemental Directives

Read and follow all safety information and
instructions to avoid possible injury or death.

Read and understand these instructions be­fore [installing / using / servicing / performing
maintenance on] this product.

Incorrect [installation / operation / servicing /
maintaining] of this product can lead to seri­ous injury. Follow all instructions.

The installation MUST comply with all ap­plicable local and national codes, including
the latest edition of the following standards:

U.S.A.

● ANSI/NFPA70, National Electrical Code
(NEC)

● ANSI/NFPA 1192, Recreational Vehicles
Code

CANADA

● CSA C22.1, Parts l & ll, Canadian Electri-
cal Code

● CSA Z240 RV Series, Recreational
Vehicles

D. General Safety Messages

 Failure to obey the following warn­ings could result in death or serious injury:

● This product MUST be [installed / serviced] by a

qualied service technician.

● Do NOT modify this product in any way. Modica-
tion can be extremely hazardous.

GENERAL INFORMATION

A. Required Tools

● Electric Drill (optional)

● Torque Wrench

● Phillips Screwdriver / Bit

● 3 mm Hex Key / Driver / Bit

● 6 mm Hex Key / Driver / Bit

● 6 mm Hex Key Socket

● 10 mm Socket

B. Required Hardware

8′ - 13′ Models:

(1) Mounting Bracket
(12) M6 X 50 mm L Carriage Bolt
(12) M6 Split Lock Washer
(12) M6 Flat Washer
(12) M6 Locknut With Nylon Insert
(6) #8-18 X .38 Self Drilling Flat Head Screw

C. Additional Hardware Quantity

15′ - 16′ Models ONLY:

(4) M6 X 50 mm L Carriage Bolt
(4) M6 Split Lock Washer
(4) M6 Flat Washer
(4) M6 Locknut With Nylon Insert
(2) #8-18 X .38 Self Drilling Flat Head Screw

3