Dodge Grand Caravan 2014 User Manual

Download

Page 1

> 2014 GRAND CARAVAN // USER GUIDE

Page 2

> IMPORTANT

This User Guide is intended to familiarize you with the important features of your vehicle.

The DVD enclosed contains your Owner’s Manual, Navigation/Uconnect Booklets, Tire Warranty and Roadside Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you

Manuals, Warranty

If you are the ﬁrst registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Uconnect® Manuals or Warranty Booklet by calling 1-800-423-6343 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer.

The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road. Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous and could lead to a serious collision. Texting while driving is also dangerous and should never be done while the vehicle is moving. If you ﬁnd yourself unable to devote your full attention to vehicle operation, pull off the road to a safe location and stop your vehicle. Some States or Provinces prohibit the use of cellular telephones or texting while driving. It is always the driver’s responsibility to comply with all local laws.

Page 3

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC . . . 2

CONTROLS AT A GLANCE

DRIVER COCKPIT ................4

INSTRUMENT CLUSTER .............6

GETTING STARTED

KEYFOB .....................8

REMOTE START .................9

VEHICLE SECURITY ALARM ..........10

SEATBELT ...................10

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) —

AIRBAGS ....................11

CHILD RESTRAINTS ..............12

FRONT SEATS .................16

REARSEATS ..................19

HEATEDSEATS ................24

HEATED STEERING WHEEL ..........25

TILT/TELESCOPING STEERING COLUMN . . . 26

ADJUSTABLE PEDALS .............27

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS . . . 28 TURN SIGNAL/WIPER/WASHER/HIGH

BEAM LEVER ..................29

HEADLIGHT SWITCH AND HALO LIGHT

SWITCH .....................31

SPEED CONTROL ................32

ELECTRONIC RANGE SELECTION (ERS) . . . 34

FUEL ECONOMY (ECON) MODE ........34

MANUAL CLIMATE CONTROLS ........35

THREE ZONE MANUAL CLIMATE CONTROLS . . 36 THREE ZONE AUTOMATIC TEMPERATURE

CONTROLS (ATC) ................37

PARKSENSE® REAR PARK ASSIST ......39

PARKVIEW® REAR BACK-UP CAMERA ....39

BLIND SPOT MONITORING WITH REAR

CROSS PATH ..................39

POWER SLIDING SIDE DOORS .........40

POWER LIFTGATE ................41

POWER SUNROOF ...............41

WIND BUFFETING ...............43

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM ......44

Uconnect® 130 .................46

Uconnect® 130 WITH SiriusXM

SATELLITE RADIO ...............48

Uconnect® 430/430N .............51

Uconnect® 730N ................60

SiriusXM SATELLITE RADIO/TRAVEL LINK . . 71

STEERING WHEEL AUDIO CONTROLS ....75

iPod®/USB/MP3 CONTROL ..........75

Uconnect® PHONE ...............76

Uconnect® VOICE COMMAND .........79

Bluetooth® STREAMING AUDIO ........82

VIDEO ENTERTAINMENT SYSTEM (VES™) . . 82 ELECTRONIC VEHICLE INFORMATION

CENTER (EVIC) .................84

PROGRAMMABLE FEATURES .........85

UNIVERSAL GARAGE DOOR OPENER

(HomeLink®) ..................86

POWER INVERTER ...............89

POWER OUTLETS ...............90

UTILITY

IN-FLOORSTORAGE—STOW'NGO® .....92

ROOF LUGGAGE RACK .............92

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) . . . 93 RECREATIONAL TOWING

(BEHIND MOTORHOME, ETC.) .........93

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE ............95

INSTRUMENT CLUSTER WARNING LIGHTS . . 95

IF YOUR ENGINE OVERHEATS .........99

TIREFIT KIT ..................100

JACKING AND TIRE CHANGING .......107

JUMP-STARTING ...............119

SHIFT LEVER OVERRIDE ...........121

TOWING A DISABLED VEHICLE ........121

FREEING A STUCK VEHICLE .........122

EVENT DATA RECORDER (EDR) ........123

MAINTAINING YOUR VEHICLE

OPENING THE HOOD .............124

ADDING FUEL .................125

ENGINE COMPARTMENT ...........126

FLUIDS AND CAPACITIES ...........127

MAINTENANCE SCHEDULE .........128

MAINTENANCE RECORD ...........131

FUSES .....................133

TIRE PRESSURES ...............136

WHEEL AND WHEEL TRIM CARE .......137

EXTERIOR BULBS ...............137

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC CUSTOMER

CENTER ....................138

CHRYSLER CANADA INC. CUSTOMER

CENTER ....................138

PUBLICATIONS ORDERING ..........138

ASSISTANCE FOR THE HEARING

IMPAIRED ...................138

REPORTING SAFETY DEFECTS IN THE

UNITEDSTATES ................139

MOPAR® ACCESSORIES

AUTHENTIC ACCESSORIES BY MOPAR® . . 140

FAQ’s

FREQUENTLY ASKED QUESTIONS ......141

INDEX

....................143

Page 4

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place. Always drive carefully.

Your new vehicle has many features for the comfort and convenience of you and your passengers. Some of these should not be used when driving because they take your eyes from the road or your attention from driving. Never text while driving or take your eyes more than momentarily off the road.

This guide illustrates and describes the operation of features andequipment that are either standard or optional on this vehicle. This guide may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this guide that are not available on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

This User Guide has been prepared to help you quickly become acquainted with the important features of your vehicle. It contains most things you will need to operate and maintain the vehicle, including emergency information.

The DVD includes a computer application containing detailed owner's information which can be viewed ona personal computer or MAC computer.Themultimedia DVD also includes videos which can be played on any standard DVD player (including the Uconnect® Touchscreen Radios). Additional DVD operational information is located on the back of the DVD sleeve.

For complete owner information, refer to your Owner's Manual on the DVD in the owner’s kit provided at the time of new vehicle purchase. For your convenience, the information

contained on the DVD may also be printed and saved for future reference.

Chrysler Group LLC is committed to protecting our environment and natural resources. By converting from paper to electronic deliveryfor the majority of the user informationfor your vehicle, together we greatly reduce the demand for tree-based products and lessen the stress on our environment.

Page 5

INTRODUCTION/WELCOME

VEHICLES SOLD IN CANADA

With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution.

WARNING!

• Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.

• Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control.

• Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle.

• Never use the ‘PARK’ position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.

• Do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

• Refer to your Owner's Manual on the DVD for further details.

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

The use of aftermarket devices including cell phones, MP3 players, GPS systems, or chargers may affect the performance of on-board wireless features including Keyless Enter-N-Go™ and Remote Start range. If you are experiencing difficulties with any of your wireless features, try disconnecting your aftermarket devices to see if the situation improves. If your symptoms persist, please see an authorized dealer.

CHRYSLER, DODGE, JEEP, RAM TRUCK, SRT, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC.

Page 6

CONTROLS AT A GLANCE

DRIVER COCKPIT

1. Headlight Switch pg. 31

2. Electronic Vehicle Information Center (EVIC) Controls pg. 84

3. Turn Signal/Wiper/Washer/High Beams Lever (behind steering wheel) pg. 29

4. Instrument Cluster pg. 6

5. Electronic Vehicle Information Center (EVIC) Display

6. Speed Control pg. 32

7. Ignition

8. Shift Lever

9. Audio System (Touchscreen Radio Shown) pg. 44

10. Automatic Climate Controls pg. 37

Page 7

CONTROLS AT A GLANCE

11. Glove Compartment

12. Switch Panel

• ParkSense® pg. 39

• ECO On pg. 34

• Electronic Stability Control (ESC) OFF pg. 97

13. DVD Player

14. Tilt/Telescoping Steering Column pg. 26

15. Hood Release pg. 124

16. Emergency Brake Pedal

17. Power Door Locks

18. Power Windows

19. Power Mirrors

Page 8

CONTROLS AT A GLANCE

INSTRUMENT CLUSTER

Warning Lights

- Low Fuel Warning Light

- Charging System Light

- Oil Pressure Warning Light**

- Anti-Lock Brake (ABS) Light**

- Air Bag Warning Light**

- Electronic Throttle Control (ETC) Light

- Tire Pressure Monitoring System (TPMS) Light

- Engine Temperature Warning Light

- Seat Belt Reminder Light

BRAKE

(See page 95 for more information.)

- Brake Warning Light**

- Malfunction Indicator Light (MIL)**

- Electronic Stability Control (ESC) Activation/Malfunction Indicator Light*

Page 9

CONTROLS AT A GLANCE

Indicators

- Turn Signal Indicators

- High Beam Indicator

- Front Fog Light Indicator

- Vehicle Security Indicator*

- Electronic Stability Control (ESC) Off Indicator*

- Electronic Speed Control ON Indicator

- Electronic Speed Control Set Indicator

Odometer Messages

door - Door Ajar noFUSE* - Fuse Fault gATE* - Liftgate Ajar CHAngE OIL* - Change Engine Oil gASCAP - Fuel Cap Fault LoCOOL - Low Coolant LoW tirE* - Low Tire Pressure

* If equipped ** Bulb Check with Key On

Page 10

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors And Liftgate

Lock The Doors And Liftgate

• Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal.

Unlock The Doors And Liftgate

• Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

All doors can be programmed to unlock on the first push of the UNLOCK button. Referto “Programmable Features” in the “Electronics” section of this guide.

Panic Alarm

• Press the PANIC button once to turn the panic alarm on.

• Wait approximately three seconds and press the button a second time to turn the panic alarm off.

1 — Left Power Sliding Door 2 — Liftgate 3—Lock 4 — Unlock 5 — Remote Start 6 — Right Power Sliding Door 7 — Emergency Key

Key Fob

Power Liftgate

• Press the LIFTGATE button twice within five seconds to power open/close the Power Liftgate. If the button is pressed twice again while the liftgate is being power closed, the liftgate will reverse to the full open position.

Power Sliding Doors

• Press the LEFT or RIGHT Power Sliding Door button twice within five seconds to power open/close the Power Sliding Door. If the button is pressed twice again while the door is being power closed, the door will reverse to the full open position.

Page 11

GETTING STARTED

Emergency Key

• Should the battery in the vehicle or the Key Fob transmitter go dead, there is an emergency key located in the Key Fob that can be used for locking and unlocking the doors. To remove the emergency key, slide the button at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.

WARNING!

• Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for anumber of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could start the vehicle, operate power windows, other controls, or move the vehicle.

• Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause them to be severely injured or killed.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

REMOTE START

• Press the REMOTE STARTbutton the REMOTE START button a third time shuts the engine off.

• To drive the vehicle, press the UNLOCK button, insert the Key Fob in the ignition and turn to the ON/RUN position.

• With remote start,the engine will onlyrun for 15 minutes (timeout) unless the ignitionKey Fob is placed in the ON/RUN position.

• The vehicle must be started with the Key Fob after two consecutive timeouts.

on the Key Fob twice within five seconds. Pressing

WARNING!

• Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause you or others to be severely injured or killed when inhaled.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause you and others to be severely injured or killed.

Page 12

GETTING STARTED

VEHICLE SECURITY ALARM

To Arm:

• Lock the door using either the power door lock switch (one door must be open) or the LOCK button on the Remote Keyless Entry (RKE) transmitter (doors can be open or closed), and close all doors.

NOTE:

The Vehicle Security Alarm will not arm if you lock the doors with the manual door lock plungers.

The Vehicle Security Light in the instrument cluster will flash for 16 seconds. This shows that the Vehicle Security Alarm is arming. During this period, if a door isopened, the ignition is cycled to ON/RUN, or the power door locks are unlocked in any manner, the Vehicle Security Alarm will automatically disarm.

NOTE:

Once armed, the Vehicle Security Alarm disables the unlock switch on the driver door trim panel and passenger door trim panel.

To Disarm The System:

• Push the Key Fob UNLOCK button or cycle the ignition to the ON/RUN position.

The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the Vehicle Security Alarm will give you a false alarm. If one of the previously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.

If the Vehicle Security Alarm is armed and the battery becomes disconnected the Vehicle Security Alarm will remain armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm.

SEAT BELT

Be sure everyone in your vehicle is in a seat and using a seat belt properly.

• Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.

• Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.

A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

Page 13

GETTING STARTED

A belt that is too loose will not protect you properly. In a sudden stop you could movetoo far forward, increasing the possibility of injury. Wear your seat belt snugly.

A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.Do not disassemble or modify thesystem. Seat belt assemblies mustbe replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).

The seat belts for both front seating positions are equipped with pretensioning devicesthat are designed to remove slack from the seat belt in the event of a collision.

A deployed pretensioner or a deployed air bag must be replaced immediately.

WARNING!

In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. Youcan strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

• This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver's Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger's Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words AIRBAG are embossed on theair bag covers.In addition, the vehicle is equipped with a Supplemental Driver Side Knee Air Bag mounted in the instrument panel below the steering column.

• The Advanced FrontAir Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision.

• This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position.

• This vehicle may be equippedwith a driver and/or front passenger seat belt buckleswitch that detects whether the driver or front passenger seat belt is fastened. The seat belt buckle switch may adjust the inflation rate of the Advanced Front Air Bags.

• This vehicle may beequipped with Supplemental Side AirBag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their covers are labeled: AIRBAG.

Page 14

GETTING STARTED

• If the Air Bag Warning Light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately.

• Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS).

NOTE: The Air Bag System is designed to be maintenance free.

WARNING!

• Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won't deploy at all. Always wear your seat belts even though you have air bags.

• Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

• Supplemental Side Air Bag Inflatable Curtains and SupplementalSeat-Mounted Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

• Being too close to the Supplemental Side Air Bag Inflatable Curtain and/or SeatMounted Side Air Bag during deployment could cause you to be severely injured or killed.

• Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

• After any collision, the vehicle should be taken to an authorized dealer immediately.

CHILD RESTRAINTS

Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.

NOTE:

• For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK (1–866–732–8243).

• Canadian residents, should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm

Page 15

GETTING STARTED

LATCH — Lower Anchors And Tethers For CHildren

• Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.

• The second row seating positions and the third row center position have lower anchors and top tether anchors.

• Youmay use the LATCHanchorage system until the combined weight of the childand the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg).

The lower anchorages are round bars that are found at the rear of the seat cushion

• where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.

In addition, there are tether strap anchors located behind each rear seatback, near

• to the floor.

• If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard position.

Page 16

GETTING STARTED

Installing The Child Restraints Using The Vehicle Seat Belts

• Except for the center position in the third row, all of the seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR). The third row center position is equipped with a cinching latch plate. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint. Any seat beltsystem will loosen with time, so check the beltoccasionally, and pull it tight if necessary.

• Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint.

Cargo Van Option Only

• The front passenger seating position is equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

• There is a tether strap anchor located on the front passenger seatback, near the floor.

To Install A Child Seat Using An ALR:

1. Pull enough of the seat belt webbing from the retractor to pass it throughthe belt path of the child restraint. Do not twist the belt webbing in the belt path.

2. Slide the latch plate into the buckle until you hear a “click.”

3. Pull on the webbing to make the lap portion tight against the child seat.

4. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all

the seat belt webbing outof the retractor.Then,allow the webbing to retractback into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode.

5. Try to pull the webbingout of the retractor.If it is locked,youshould not be able topull out

any webbing. If the retractor is not locked, repeat the last step.

6. Finally, pull up on any extra webbing to tighten the lap portion around the child restraint

while you push the child restraint rearward and downward into the vehicle seat.

Page 17

GETTING STARTED

7. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See below for directions to attach a tether anchor.

8. Test that the child restraint is installed tightly by pulling back and forth on the child seat

at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

To Install A Child Seat Using A Cinching Latch Plate:

1. Place the child seat in the center of the seating position.

2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt

path of the child restraint. Do not twist the belt webbing in the belt path.

3. Slide the latch plate into the buckle until you hear a “click.”

4. Finally,pull up on any excesswebbingto tighten the lapportion around the child restraint

while you push the child restraint rearward and downward into the vehicle seat.

5. If the child restraint has a top tether strap and the seating position has a top tether

anchorage, connect the tether strap to the anchorage and tighten the tether strap. See below for directions to attach a tether anchor.

6. Test that the child restraint is installed tightly by pulling back and forth on the child seat

at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt):

When installing a forward-facing child restraint, always secure the top tether strap, up to the tether anchorweight limit, whether the child restraint is installed with the lower anchors or the vehicle seat belt.

1. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.

2. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint,

and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint.

Attach the tether strap hook of the child restraint to the top tether anchorage and remove

slack in the tether strap according to the child restraint manufacturer’s instructions.

Page 18

GETTING STARTED

WARNING!

• In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size.

• Rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger air bag. An air bag deployment could cause severe injury or death to infants in this position.

• Only use a rearward-facing child restraint in a vehicle with a rear seat.

• Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be severely injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.

• An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.

• If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.

FRONT SEATS

Power Seat

• The power seat switch controls forward/ back, up/down, and tilt adjustment.

• The recline switch, located on the outboard side of the seat, controls seatback adjustment.

Power Lumbar

• Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support.

Power Seat Switches

1 — Lower Seat Switch 2 — Recline Switch 3 — Power Lumbar Switch

Page 19

GETTING STARTED

Manual Seat Adjustment

Forward/Rearward

• Lift up on the adjusting bar located at the front of the seat near the floor and release it when the seat is at the desired position. Then, using body pressure, move forward and backward on the seat to be sure that the seat adjusters have latched.

Recliner

• Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position.

1 — Recliner Lever 2 — Forward/Rearward Adjusting Bar

Memory Seat

• The memory seat feature allows you to save two different driver seating positions, driver's outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. The memory seat buttons are located on the driver's door panel.

• To set a memory position:

1. Cycle the vehicles ignition to the ON position.

2. Adjust all memory profile settings.

3. Press and release the S (SET) button.

4. Press and release the 1 or 2 button within five seconds.

Seat Adjustment Locations

Memory Seat Button Location

Page 20

GETTING STARTED

NOTE:

Before programming your RKE transmitters you must select the select “RKE Linked to Memory” in the Electronic Vehicle Information Center (EVIC). Refer to “Programmable Features” in “Electronics” for further information.

• To program a Key Fob to the memory position:

1. Cycle the vehicles ignition to the OFF position.

2. Select the desired memory profile 1 or 2.

3. Press andrelease the S (SET)button on the memory switch, then withinfive seconds press and release the 1 or 2 button accordingly.

4. Press and release the LOCK button on the RKE transmitter within 10 seconds.

• To recall the saved positions, press 1 or 2 on the memory switch or press UNLOCK on the programmed RKE transmitter.

CAUTION!

Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls.Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.

WARNING!

• Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause youtolose control. The seat belt mightnot be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.

• Donot ride with the seatbackreclined so that the seatbeltis no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked.

Page 21

REAR SEATS

Second Row Seats — Stow 'n Go®

• On vehicles equipped with Stow 'n Go® seats, the seats will fold and tumble in one motion.

• Move the front seat fully forward.

• Recline the front seatback fully forward.

• Raise the armrests on the second row seat.

NOTE:

Seat will not stow in the storage bin unless the armrests are raised.

GETTING STARTED

Seatback Lever Location

Storage Bin Lock Location

Page 22

GETTING STARTED

• Slide the storage bin locking mechanism to the “LOCK” position and then pull up on the storage bin latch to open the cover.

• Pull upward on the seatback recliner lever located on the outboard side of the seat.

• The non-adjustable head restraint and seatback will fold automatically during the seat tumble.

• The seat will automatically tumble into position for easy storage.

• Push the seat into the storage bin and close the storage bin cover.

To Unstow Second Row Seats

• Pull up on the storage bin latch to open the cover.

• Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors.

• Lift the seatback to the full upright position.

• Return the head restraint to its upright position, close the storage bin cover and slide the storage bin locking mechanism to the “UNLOCKED” position.

Headrest In Stowed Position

Seat In Tumble Position

Seat In Stored Position

Page 23

GETTING STARTED

Third Row Seats

Third Row Power Recliner

• The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort.

Third Row Power Seat Switch

NOTE:

Disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats.

• A one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank.

• Left and right third row seats can be folded individually or together. The third row power folding seats adjust to multiple positions.

• The switch is only functional when the liftgate is open and the vehicle is in PARK.

• To abort seatoperation while the seat is in motion, press a different seat position selector switch to stop the seat. Once the seat stops moving, then the desired position can be selected.

• The third row power seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion a short distance to move the seat away from the obstacle. Should this occur, remove the obstacle and press the button again for the desired position.

• Refer to your Owner's Manual on the DVD for manual third row seat folding instructions.

Third Row Power Seat Switch

Page 24

GETTING STARTED

Manually Folding Third Row Seats

• Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down.

• Lower the outboard head restraints by pulling on the release strap marked “1” located on the outboard side of the head restraint.

Pull release strap marked “2” located on

• the rear of the seat to lower the seatback.

• Pull release strap marked “3” to release the anchors.

Center Headrest In Lowered Position

Head Restraints In Lowered Position

Seatbacks In Folded Position

Page 25

GETTING STARTED

• Pull release strap marked “4” and tumble the seat rearward into the storage bin.

To Unfold Third Row Seats

• Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch.

• Pull release strap marked “2” to unlock the recliner.

• Pulling strap “4” releases the seatback to return to its full upright position.

• Raise the head restraint to its upright position.

CAUTION!

The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

• In a collision, seriousinjury could resultif the seat storage bin covers are notproperly latched.

• Do not drive the vehicle with the storage bin covers open.

• Keep the storage bin covers closed and latched while the vehicle is in motion.

• Do not use a storage bin latch as a tie down.

• In a collision, you or othersin the vehicle could be injured if the seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

Seats In Stowed Position

Page 26

GETTING STARTED

HEATED SEATS

Front Heated Seats

• The controls for front heated seats are located on the center instrument panel area.

• Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

• If the High-level setting is selected, the system will automatically switch to Lowlevel after approximately60 minutes. The Low-level setting will turn Off automatically after approximately 45 minutes.

Second Row Heated Seats

•

Second row heated seat switches are located in the sliding door handle trim panels.

• Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

Heated Seat Switch Location

Heated Switch Location

Page 27

GETTING STARTED

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

HEATED STEERING WHEEL

• The steering wheel contains a heating element that heats the steering wheel to one temperature setting.

• The heated steering wheel switch is located on the center instrument panel.

• Press the switch once to turn the heating element On. Press the switch a second time to turn the heating element Off.

• Once the heated steering wheel has been turned on, it will operate for approximately 30 to 80 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.

Heated Steering Wheel Switch Location

Page 28

GETTING STARTED

TILT/TELESCOPING STEERING COLUMN

• The tilt steering column tilt lever is located below the steering wheel.

• Push down on the tilt lever to unlock the steering column.

• With one hand firmly on the steering wheel, move the steering column upward or downward as desired.

• To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.

• Pull upward on the tilt lever to lock the column firmly in place.

Steering Column Lever

WARNING!

Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle. Failure to follow this warning may result in you and others being severely injured or killed.

Page 29

GETTING STARTED

ADJUSTABLE PEDALS

• Press the switch located on the left side of the steering column forward to move the brake and accelerator pedals away from the driver and press the switch rearward to move the pedals closer to the driver.

NOTE:

The pedals cannot be adjusted when the vehicle is in REVERSE or when theElectronic Speed Control is set.

Adjustable Pedal Switch

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal's path.

WARNING!

Do not adjust the pedals while the vehicle is moving. You could lose control and have a collision. Always adjust the pedals while the vehicle is parked.

Page 30

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.

Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.

While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.

The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintaining Your Vehicle.”

NOTE:

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal partof the break-in and notinterpreted as an indication of an engine problem or malfunction.

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.

Page 31

OPERATING YOUR VEHICLE

TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER

Multifunction Lever

1 — Mist (Push To First Detent) 2 — Rear Wiper/Washer 3 — Push Lever For High Beams 4 — Front Wipers 5 — Front Washer (Push To Second Detent)

Turn Signal/Lane Change Assist

• Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off.

• Vehicles equipped with Blind Spot Monitoring will produce a visual alert and may be programmed to produce an audible alert when signaling a lane change; refer to your Owner’s Manual on the DVD for operation.

Front Wipers

Intermittent, Low And High Operation

• Rotate the end of the lever to the first detent positionfor one of fiveintermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.

Page 32

OPERATING YOUR VEHICLE

Rain Sensing Wipers

• This feature senses moisture on the vehicle’s windshield and automatically activates the wipers for the driver when the switch is in the intermittent positions. Refer to Programmable Features in Electronics for further details.

Mist

• Push the end of the lever inward to the first detent when a single wipe is desired.

NOTE:

The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be activated in order to spray the windshield with washer fluid.

Washer Operation

• Push the end of the lever inward to the second detent and hold for as long as spray is desired.

Rear Wiper

• Rotate the center portion of the lever forward to the first detent for rear wiper operation.

Rear Washer

• Rotate the center portion of the lever past the first detent to activate the rear washer.

High Beams

• Push the lever away from you to activate the high beams.

A high beam symbol will illuminate in the cluster to indicate the high beams are on.

NOTE:

For safe driving, turn off the high beams when oncoming traffic is present to prevent headlight glare and as a courtesy to other motorists.

Flash To Pass

• Pull the lever toward you to activate the high beams. The high beams will remain on until the lever is released.

Page 33

OPERATING YOUR VEHICLE

HEADLIGHT SWITCH AND HALO LIGHT SWITCH

Automatic Headlights/Parking Lights/Headlights

• Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent for parking lights for headlights

• With the parking lights or low beam headlights on, push the headlight switch once for fog lights.

• Rotate the headlight switch to AUTO for Automatic Headlights.

• When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.

Instrument Panel Dimmer

• Rotate the dimmer control to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened.

• Rotate the dimmer control up to increase the brightness of the instrument panel when the parking lights or headlights are on.

• Rotate the dimmer control up to the next detent position to fully brighten the odometer and radio when the parking lights or headlights are on.

• Rotate the dimmer control up to the last detent position to turn on the interior lighting.

and to the second detent

Headlight Switch/Halo Light Switch

1—Auto 2 — Push Fog Light 3 — Rotate Halo Light Dimmer Control 4 — Rotate Dimmer Control 5 — Rotate Headlight Switch

Overhead (Halo) Light

• To activate the Halo lights,rotate the Halo switch control upwardordownwardto increase or decrease the lighting.

Page 34

OPERATING YOUR VEHICLE

SPEED CONTROL

The Speed Control switches are located on the steering wheel.

Cruise ON/OFF

• Push the ON/OFF button to activate the Speed Control.

CRUISE cluster to indicate the Speed Control is on.

• Push the ON/OFF button a second time to turn the system off.

SET

• With the Speed Control on, push and release the SET – button to set a desired speed.

Accel/Decel

To Increase Speed

• When the Electronic Speed Control is set, you can increase speed by pushing the RES + button.

The speed increment shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

• Pressing the RES + button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph.

• If the button is continually pressed, the set speed will continue to increase until the button is released, then the new set speed will be established.

Metric Speed (km/h)

• Pressing the RES + button once will result in a 2 km/h increase in set speed. Each subsequent tap of the button results in an increase of 2 km/h.

• If the button is continually pressed, the set speed will continue to increase until the button is released, then the new set speed will be established.

will appear on the instrument

Speed Control Switches

1 — Push On/Off 2 — Push Resume/Accel 3 — Push Set/Decel 4 — Push Cancel

Page 35

OPERATING YOUR VEHICLE

To Decrease Speed

• When the Electronic Speed Control is set, you can decrease speed by pushing the SET button.

The speed decrement shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

• Pressing the SET - button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph.

• If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established.

Metric Speed (km/h)

• Pressing the SET - button once will result in a 2 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 2 km/h.

• If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established.

Resume

• To resume a previously selected set speed in memory, push the RES + button and release.

Cancel

• Push the CANCEL button, or apply the brakes to cancel the set speed and maintain the set speed memory.

• Push the ON/OFF button to turn the system off and erase the set speed memory.

WARNING!

• Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic Speed Control system off when you are not using it.

• Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

Page 36

OPERATING YOUR VEHICLE

ELECTRONIC RANGE SELECTION (ERS)

• Electronic Range Select (ERS) allows you to limit the highest available transmission gear,and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.

• To shift from DRIVE mode to ERS mode, move the shift lever to the left (-) once. The current gear will be maintained as the top gear.To disable ERS, simply press and hold the shift lever to the right (+) until “D” is displayed in the instrument cluster odometer.

• Switching between ERS and DRIVE mode can be done at any vehicle speed.

• Refer to your Owner's Manual on the DVD for further details.

FUEL ECONOMY (ECON) MODE

•

The Fuel Economy (ECON) mode can improve the vehicle’s overall fuel economy during normal driving conditions.

• Press the ECON switch in the center stack of the instrument panel and a green light will indicate the ECON mode is engaged.

• When the ECON Mode is engaged, the vehicle control systems will be able to change the following:

• The transmission will upshift sooner and downshift later.

• The transmission will skip select gears during shifts to allow the engine to operate at lower speeds.

• The torque converter clutch may engage sooner (lower engine rpm’s) and remain on longer.

• The engine idle speed will be lower.

• The overall driving performance will be more conservative.

Page 37

OPERATING YOUR VEHICLE

MANUAL CLIMATE CONTROLS

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

• Recirculation is allowed in floor mode.

• Recirculation is allowed in defrost/floor (mix modes) for approximately five minutes.

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

• Pressing the rear window defroster button will turn on the defroster for approximately 10 minutes. An indicator in the button will illuminate when the rear window defroster is on. For an additional 10 minutes of operation, press the button a second time.

Page 38

OPERATING YOUR VEHICLE

THREE ZONE MANUAL CLIMATE CONTROLS

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

• Recirculation is allowed in floor mode.

• Recirculation is allowed in defrost/floor (mix modes) for approximately five minutes.

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

Page 39

OPERATING YOUR VEHICLE

Activating Rear Passenger Climate Controls

• Rotate the rear blower control, located on the main climate control in the instrument panel to the “REAR” position. This enables the rearpassenger climate controls locatedin the headliner above the second row seats.

THREE ZONE AUTOMATIC TEMPERATURE CONTROLS (ATC)

Automatic Operation

• Push the AUTO mode button to activate the ATC system.

• Select the desired temperature by pressing the temperature control buttons for the driver or passenger.

• The system will maintain the set temperature automatically.

Page 40

OPERATING YOUR VEHICLE

Air Conditioning (A/C)

• If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C. The mode and blower will go to the previous user setting.

SYNC Temperature Button

• Push the SYNC button once to control driver and passenger temperatures simultaneously. Push the SYNC button a second time to control the temperatures individually.

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

• If the Recirculation button is pressed when the system is in Defrost mode the Recirculation LED indicator will flash three times to indicate Recirculation mode is not allowed.

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

Activating Rear Automatic Temperature Control

• Pressing the REAR LOCK button for the Rear Automatic Temperature Control (ATC) System from the front lower ATC panel, illuminates a LOCK symbol in the rear display. The rear temperature and air source are controlled from the front lower ATC panel.

• Rear second row occupants can only adjust the rear ATC control when the REAR LOCK button is turned off.

• The Rear ATC system is located in the headliner, near the center of the vehicle.

Page 41

OPERATING YOUR VEHICLE

PARKSENSE® REAR PARK ASSIST

• If an object isdetected behind the rear bumper while the vehicle is in REVERSE,a warning will display in the instrument cluster and a tone will sound, (closer the object the faster the tone) that changes speed depending on the distance of the object from the bumper, will sound.

• When the Instrument Cluster reads either “Clean Sensor” or “Blinded”, clean off the bumper sensors to see if the condition is corrected.

PARKVIEW® REAR BACK-UP CAMERA

You can see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The ParkView® Rear Back-Up Camera image will be displayed on the radio display screen, located on the center stack of the instrument panel.

If the radio display screen appears foggy, clean the camera lens located on the liftgate.

Refer to your Owner's Manual on the DVD for further details.

WARNING!

Drivers must be careful when backing up; even when using the ParkView® Rear Back-Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You must continue to pay attention while backing up. Failureto do so can result in serious injury or death.

BLIND SPOT MONITORING WITH REAR CROSS PATH

• The Blind Spot Monitoring (BSM) system uses two radar-based sensors, located inside the rear bumper fascia, to detect Highway licensable vehicles (automobiles, trucks, motorcycles etc.) that enter the blind spot zones from the rear/front/side of the vehicle.

• The Blind Spot Monitoring (BSM) system warning light, located in the outside mirrors, will illuminate if a vehicle moves into a blind spot zone.

• The BSM system can also be configured to sound an audible (chime) alert and mute the radio to notify you of objects that have entered the detection zones.

• Refer to your Owner's Manual on the DVD for further details.

Page 42

OPERATING YOUR VEHICLE

POWER SLIDING SIDE DOORS

Automatic/Manual Operation

• The power sliding door may be opened or closed manually or by using the buttons on the Key Fob, overhead console switch, or rear door switch.

• Pulling the inside or outside power sliding door handle will also power open the power sliding doors.

NOTE:

When the power sliding door master lock switch is in the OFF position, the power sliding side door may notbe opened or closed by pressing the switch located on the b-pillar trim panel, just in thefront of the sliding door or activating the inside power sliding door handle.

Sliding Side Door Child Protection Lock

• When this system is engaged, the inside manual door handle will not open the sliding door even though the inside door lock is in the unlocked position.

• To engage the Child Protection Door Lock, open the sliding side door. Slide the child protection door lock control, located on the rear of the sliding door, inward (toward the vehicle) to engage.

• Repeat these steps on the opposite sliding door.

Page 43

OPERATING YOUR VEHICLE

POWER LIFTGATE

• The power liftgate may be opened and closed by pressing the button located on the overhead console. Press the button once to open, and a second time to close the power liftgate.

• The power liftgatemay also beopened and closed by pressing the button on theKey Fob. Press the button twice to open, and twice to close the power liftgate.

• The power liftgate may be closed by the button, located in the upper left trim in the liftgate opening. Pressing once will only close the liftgate. This button cannot be used to open the liftgate.

POWER SUNROOF

• The power sunroof switch is located on the overhead console.

Opening Sunroof

Express Open

• Press the switch rearward and release it within one-half second. The sunroof will fully open and stop automatically.

Manual Open

• Press and hold the switch rearward to open the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open position until the switch is pressed again.

Venting Sunroof

• Press and releasethe button and the sunroof will open to the vent position.

This is called “Express Vent” and will occur regardless of sunroof position. During Express Ventoperation, any movementof the switch will stop the sunroof.

1 — Opening Sunroof 2 — Venting Sunroof 3 — Closing Sunroof

Power Sunroof Switch

Page 44

OPERATING YOUR VEHICLE

Closing Sunroof

Express Closing

• Press the switch forward and release it within one-half second. The sunroof will fully close automatically from any position.

Manual Closing

• Press and hold the switch forward toclose the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially closed position until the switch is pressed again.

Pinch Protection Feature

• This feature will detect an obstruction in the opening of the sunroofduring Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.

NOTE:

If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled.

Page 45

OPERATING YOUR VEHICLE

WARNING!

• Never leave children unattended in a vehicle, and do not leave the Key Fob in or near the vehicle, and do not leave a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

• In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be severely injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

• Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

WIND BUFFETING

Wind buffeting can be described as a helicopter-type percussion sound. If buffetingoccurs with the rear windows open, adjust the front and rear windows together.

If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.

Page 46

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM

1. Uconnect® Voice Command Button pg. 79

2. Uconnect® Phone Button pg. 76

3. Steering Wheel Audio Controls (Left) pg. 75

4. Steering Wheel Audio Controls (Right) pg. 75

Page 47

ELECTRONICS

5. USB port pg. 55

6. Audio Jack pg. 55

7. USB Port (inside upper glove box) pg. 64

Page 48

ELECTRONICS

Uconnect® 130

NOTE:

• Your radio has many features that add to the comfort and convenience for you and your passengers.

• Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

1. Press and hold the TIME button until the hours blink.

2. Turn the TUNE/SCROLL control knob to set the hours.

3. Press the TUNE/SCROLL control knob until the minutes begin to blink.

4. Turn the TUNE/SCROLL control knob to set the minutes.

5. Press the TUNE/SCROLL control knob to save the changes.

6. Press any button/knob or wait five seconds to exit.

Equalizer, Balance And Fade

1. Press the TUNE/SCROLL control knob and “BASS” will display.

2. Rotate the TUNE/SCROLL control knob to select the desired setting.

3. Continue pressing the TUNE/SCROLL control knob to display and set “MID RANGE,”

“TREBLE,” “BALANCE” and “FADE.”

Page 49

ELECTRONICS

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM or FM bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the SET/RNDor SET (depending on the radio) button once and SET 1 will showin the display. Then select a preset button (1–6).

• A second station may be added to each push button. Press the SET/RND or SET (depending on the radio) button twice and SET 2 will show in the display. Then select a preset button (1–6).

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND Or RND (Depending On Radio) Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

Audio Jack Operation

The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle’s sound system. This requires the use of a 3.5 mm stereo audio patch cable.

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 50

ELECTRONICS

Uconnect® 130 WITH SiriusXM SATELLITE RADIO

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. Todetermine if yourradio has these features, press the VoiceCommand button on the radio.You will hear a voice prompt if youhave the feature, or seea message on the radio stating “Uconnect Phone not available” if you do not.

• Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio featuresshould not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

1. Press and hold the TIME button until the hours blink.

2. Turn the TUNE/SCROLL control knob to set the hours.

3. Press the TUNE/SCROLL control knob until the minutes begin to blink.

4. Turn the TUNE/SCROLL control knob to set the minutes.

5. Press the TUNE/SCROLL control knob to save the changes.

6. Press any button/knob or wait five seconds to exit.

Page 51

ELECTRONICS

Equalizer, Balance And Fade

1. Press the TUNE/SCROLL control knob and “BASS” will display.

2. Rotate the TUNE/SCROLL control knob to select the desired setting.

3. Continue pressing the TUNE/SCROLL control knob to display and set “MID RANGE,” “TREBLE,” “BALANCE” and “FADE.”

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM, FM, or SAT bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the SET/RNDor SET (depending on the radio) button once and SET 1 will showin the

display. Then select a preset button (1–6).

• A second station may be added to each push button. Press the SET/RND or SET

(depending on the radio) button twice and SET 2 will show in the display. Then select a preset button (1–6).

Music Type

NOTE:

The Music Type function only operates when in FM mode.

• Press the MUSIC TYPE button to activate this mode. Press the MUSIC TYPE button again

or turn the TUNE/SCROLL control knob to select the desired music type (Adult Hits, Country, Jazz, Oldies, Rock, etc.).

• When a music type is chosen and the Music type is displayed, press either SEEK button

and the radio will only search for stations with the selected music type.

SETUP Button

• Pressing the SETUP button allows you to select between items that are available in that

particular mode.

• Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/

SELECT button to select an entry and make changes.

Page 52

ELECTRONICS

SiriusXM Satellite Radio

SiriusXM services requiresubscriptions,sold separately after the 12-monthtrialincluded with the new vehicle purchase.

subscription, the plan you choose will automatically renew and bill at then-current rates until you call SiriusXM at 1-866-635-2349 to cancel. See SiriusXM Customer Agreement

for complete terms at http://www.siriusxm.com. All fees and programming subject to change. Our satellite service is available only to those at least 18 and older in the 48 contiguous USA and D.C. Our Sirius satellite service is also available in PR (with coverage limitations). Our Internet radio service is available throughout our satellite service area and in AK and HI. ©2014 Sirius XM Radio Inc. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc.

SiriusXM Satellite Radio gives you over 130 channels, including 100% commercial-free music from nearly every genre, plus all your favorite sports, news, talk and entertainment channels–all with crystal clear, coast-to-coast coverage, all in one place and all at your fingertips.

• To access SiriusXM Satellite Radio, press the SAT hard-key.

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND or RND (Depending On Radio) Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

LIST Button

• Press the LIST button to bring up a list of all folders on the CD. Scroll up or down the list by turning the TUNE/SCROLL control knob.

• To select a folder from the list, press the TUNE/SCROLL control knob and the radio will begin playing the files contained in that folder.

If you decide to continue your service at the end of your trial

Audio Jack Operation

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 53

ELECTRONICS

Uconnect® 430/430N

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. Todetermine if yourradio has these features, press the VoiceCommand button on the radio.You will hear a voice prompt if youhave the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.

Clock Setting

1. Turn the radio on, then touch the screen where the time is displayed.

2. Touch the “User Clock” soft-key or the time display (Navigation radio only).

3. To adjust the hours, touch either the “Hour Forward” or “Hour Backward” soft-key.

4. To adjust the minutes, touch either the “Minute Forward” or “Minute Backward” soft-key.

5. To save the new time setting, touch the screen where the word “Save” is displayed.

Equalizer, Balance And Fade

Audio Control Menu

• Press the AUDIO hard-key on the right side of the radio.

• Use either the “arrow” soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE.

• Touch the “BAL/FADE” soft-key and use either the “arrow” soft-keys or the crosshair on the screen to change Balance and Fade. The “Center” soft-key resets the settings.

Display Settings

• Press the MENU hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “Exit” soft-key to save your settings.

Page 55

ELECTRONICS

Radio Operation

• To access Radio Mode, touch the RADIO hard-key on the left side of the faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen to select the band.

Seek Up/Seek Down

• Press the “SEEK UP” or “SEEK DOWN” soft-keysto seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.

• Find the station to store by either pressing the “SEEK UP” or “SEEK DOWN” soft-keys, touching the “Scan” soft-key, or by using the “Direct Tune” soft-key.

• Once the station isfound,touch and hold one of the “PRESETS” soft-keysin the list to the right, until the preset key flashes and the station text on the soft-key changes.

NOTE:

If the Presets are not visible on the right side of the screen, press the “PRESETS” soft-key.

Page 56

ELECTRONICS

CD/DVD Disc Operation

• Press the MEDIA hard-key to display the media source tabs at the top of the screen. Select the source by touching the “HDD,” “DISC” or “AUX” media source soft-key tab.

NOTE:

Your Touchscreen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert A CD/DVD Disc

• To insert a disc, press the LOAD hard-key.

• With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen. The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows “Reading...” during this process.

Seek Up/Seek Down

• Press the SEEK UPor SEEK DOWN hard-keys to seekthrough tracks in Disc Mode.Holding the SEEK UP soft-key will fast forwardthrough the track until the beginningof the track is reached; if still held it will fast-forward through the next sequential track(s) (if random play node is not active) until released. Holding the SEEK DOWN soft-key will fast-reverse through the track until the beginning ofthe track is reached;if still held it will fast-reverse through the next sequential track(s) (if random play node is not active) until released.

Page 57

ELECTRONICS

Audio Jack Operation

• The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle’s sound system. This requires the use of a 3.5 mm stereo audio patch cable.

• Press the MEDIA hard-key thenthe “AUX” soft-key to change themode to auxiliarydevice if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks.

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

• Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs and pictures can be added to the hard drive by using a CD or USB device (e.g. thumb drive or memory stick).

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 430/430N User's Manual for more information.

Copying Music From CD

• Press the LOAD hard-key.

• Insert a disc, then press the MY FILES hard-key. Select the “MY MUSIC” soft-key.

• Touch the “Add Music Files to HDD” soft-key, then touch the “Disc” soft-key in the next screen to start the process.

NOTE:

• Youmight need to select the folder or title depending on the CD, then press “DONE” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Page 58

ELECTRONICS

Copying Music From USB

• The USB port on the radio face plate allows you to copy files to your hard drive.To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select the “MY MUSIC” soft-key.

• Touch the “Add Music Files to HDD” soft-key, then touch the “Front USB” soft-key in the next screen.

• Select the folders or titles you would like to copy, then touch the “SAVE”soft-key to start the copy process.

• To copy all of the titles, touch the “ALL” soft-key then touch the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in JPEG format.

• Press the MY FILES hard-key.

• Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “Disc” or “USB” soft-key, then select the foldersor pictures you wish to copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.

• Touch the desired pictures or press the “All” soft-key for all pictures. Confirm your selections by touching the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Display A Picture On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

• Press the MY FILES hard-key, then touch the “My Pictures” soft-key. Touch the desired picture, touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly press the MENU hard-key and touch the “Picture View” soft-key to display the chosen picture on the radio screen.

NOTE:

• A check mark in the My Pictures screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Page 59

ELECTRONICS

Playing Music From The HDD

• Press the MEDIA hard-key to display the media source tabs at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touchscreen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touchscreen.

• If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Always follow the solvent manufacturer's precautions and directions.

Garmin® Navigation

• Uconnect® 430N integrates Garmin’s consumer-friendly navigation into your vehicle. Garmin® Navigation includes a database with over six million points of interest.

• Touch the “NAV” soft-key in the upper right corner of the screen to access the Navigation system.

Changing The Navigation Voice Prompt Volume

1. Program a destination.

2. While traveling on your route, touch the

upper left area of the map screen where your next turn is displayed.

3. The Navigation system will then repeat

the distance to your next turn.

4. While the Navigation system is speaking, use the ON/OFF VOLUME rotary knob to adjust

the volume to a comfortable level. Please note the volume setting for Navigation Voice Prompt is different than the audio system.

NOTE:

For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion.

Page 60

ELECTRONICS

Main Navigation Menu

Finding Points Of Interest

• From the main Navigation menu, touch the “Where To?”soft-key, then touch the “Points of Interest” soft-key.

• Select a Category, then a subcategory, if necessary.

• Select your destination and touch the “Go” soft-key.

Finding A Place By Spelling The Name

• From the Main Navigation Menu touch the “Where To?” soft-key. Next, touch the “Points of Interest” soft-key then touch the “Spell Name” soft-key.

• Enter the name of your destination.

• Touch the “Done” soft-key.

• Select your destination and touch the “Go” soft-key.

Entering A Destination Address

• From the main Navigation menu touch the “Where To?” soft-key, then touch the “Address” soft-key.

• Follow the on-screen prompts to enter the address then touch the “Go” soft-key.

Setting Your Home Location

• From the main Navigation menu touch the "Tools"icon. Next select the "My Data" folder icon. Then select "Set Home Location."

• You may enter your address directly, use your current location as your home address, or choose from recently found locations.

Edit Home Location

• From the main Navigation menu touch the “Where To?” soft-key, then touch the "Tools" icon. Next, touch the "My Data" folder.

• You may enter a new address directly, use your current location or choose from recently found locations.

Go Home

• A Home location must be saved in the system. From the Main Navigation menu, touch the “Where To?” soft-key, then touch the “Go Home” soft-key.

Page 61

ELECTRONICS

Following Your Route

• Yourroute ismarkedwith a magenta line onthe map. If you departfromthe original route, your route is recalculated. A speed limit icon could appear as you travel on major roadways.

Adding A Via Point

• To add a stop between the current location and the end destination (Via Point) you must be navigating a route.

• Touch the “back arrow” icon multiple times to return to the Main Navigation menu.

• Touch the “Where To?” soft-key, then search for the additional stop. Select the destination you wish to add from the given search results.

• Touch the “Go” soft-key, then touch "Add as a Via Point" soft-key and press the "Done" soft-key.

Taking A Detour

• To take a detour you must be navigating a route. Touch the “back arrow” icon soft-key multiple times to return to the Main Navigation menu.

•

• Touch the “Detour” soft-key.

NOTE:

If the route you are currently taking is the only reasonable option, the device might not calculate a detour.

Page 62

ELECTRONICS

Acquiring Satellites

• The GPS Satellite strength bars indicate the strength of your satellite reception.

• Acquiring satellite signals can take a fewminutes. When at least one of the bars is green, your device has acquired satellite signals.

• You may experience delays receiving satellite signals when in areas with an obstructed view to the sky, such as garages, tunnels, or large cities with tall buildings.

Uconnect® 730N

NOTE:

Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

1. Turn the radio on, then touch the screen where the time is displayed.

2. Touch the “User Clock” soft-key.

3. To adjust the hours, touch either the “Hour Forward” or “Hour Backward” soft-key.

4. To adjust the minutes, touch either the “Minute Forward” or “Minute Backward” soft-key.

5. To save the new time setting, touch the screen where the word “Save” is displayed.

Page 63

ELECTRONICS

Equalizer, Balance And Fade

Audio Control Menu

• Press the MENU hard-key on the rightside of the radio. Then press the “Audio Control” soft-key to get to the audio control menu.

• Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “Center” soft-key resets the settings.

• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE.

Display Settings

• Press the MENU hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “EXIT” soft-key to save your settings.

Page 64

ELECTRONICS

Radio Operation

• To access RadioMode, touch the RADIO/MEDIA hard-key on the left side of the faceplate repeatedly until AM/FM/SATappears at the top of the screen, then touch the “AM,” “FM” or “SAT” soft-key to select the band.

Seek Up/Seek Down

• Press the SEEK UP or SEEK DOWN hard-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM” or “SAT” soft-key.

• Find the station to store by either pressing the SEEK UP or SEEK DOWN hard-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.

• Once the station isfound,touch and hold one of the “PRESETS” soft-keysin the list to the right, until you hear a confirmation beep.

NOTE:

If the Presets are not visible on the right side of the screen, press the “PRESETS” soft-key.

Page 65

ELECTRONICS

CD/DVD Disc Operation

• Press the RADIO/MEDIA hard-key until the media source tabs are displayed at the top of the screen. Select the source by touching the “HDD,” “DISC” or “AUX” media source soft-key tab.

NOTE:

Your Touchscreen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert A CD/DVD Disc

• To insert a disc, press the OPEN/CLOSE hard-key.

Seek Up/Seek Down

• Press the SEEK UP or SEEK DOWN hard-keys to seek through tracks in Disc Mode. Hold either SEEK to bypass tracks without stopping.

Page 66

ELECTRONICS

Audio Jack Operation

• Press the RADIO/MEDIA hard-key, then the “AUX” soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. The volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and selective Songs from a CD can also be added to the HDD. See the Uconnect® 730N Supplement Manual for more information.

Copying Music From CD

• Press the OPEN/CLOSE hard-key.

• Insert a disc, then press the MENU hard-key.

• Touch the “MY FILES” soft-key, then select “MY MUSIC.”

Page 67

ELECTRONICS

• Touch the “Add Music Files to HDD” soft-key, then touch the “From Disc” soft-key in the next screen to start the process.

NOTE:

• Youmight need to select the folder or title depending on the CD, then press “Done” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Copying Music From USB

• The USB port on the radio face plate allows you to copy files to your hard drive.To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select “MY FILES.”

• Touch the “MY MUSIC” soft-key, then touch the “Add Music Files” to HDD soft-key.

• Touch the “From USB” soft-key, then select the folders or titles you would like to copy, and then touch the “SAVE” soft-key to start the copy process.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in .jpg/JPEG format.

• Press the MENU hard-key to access the Settings Menu, then touch the “My Files” soft-key.

• Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “From Disc” or “From USB” soft-key, then select the folders or pictures you wish to copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.

Touch the desired picturesor press the “All”

• soft-key for all pictures. Confirm your selections by touching the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Page 68

ELECTRONICS

Display A Picture On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

• Press the MENU hard-key to access the Settings Menu.

• From the Settings menu, touch the “My Files” soft-key and then touch the “My Pictures” soft-key.

• Touch the desired picture, touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key.

• To display the chosen picture on the radio screen, press the MENU hard-key and touch the “Picture View” soft-key.

NOTE:

• A check mark in the My Pictures screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Playing Music From The HDD

• Press the RADIO/MEDIA hard-key until the media source tabs are displayed at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touchscreen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touchscreen.

Page 69

ELECTRONICS

Navigation

• Your navigation system receives GPS signals from up to 16 satellites to display the position of your vehicle. Map and database information is supplied through a hard disk drive.

• Touch the NAV hard-key on the radio face plate to access the Navigation system and the NAV – Main Menu.

Changing The Navigation Guidance Prompt Volume

1. From the Navigation Map screen, touch the MENU hard-key then touch the “NAV Settings” soft-key. Next select "Guidance Prompts."

2. Select and adjust the navigation guidance prompt volume using the left and right

arrows.

3. Touch the “SAMPLE VOL” soft-key to lis-

ten to the current volume setting.

4. Once satisfied with the volume,touch the

“SAVE” soft-key to save the settings. Touch the “CANCEL” soft-key to exit the menu without saving the settings.

NOTE:

For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion.

Page 70

ELECTRONICS

Main Navigation Menu

Finding Points Of Interest

1. From the NAV - Main Menu, touch the “Points of Interest” soft-key.

2. Select a Category and then a subcategory, if necessary.

3. Select your destination and touch “GO.”

Finding A Place By Entering The Street Address

NOTE:

Entering the city or zip code before entering the street name facilitates address entry.If the State and/or Country displayed areincorrect, touch the correspondingsoft-key to make the correction.

1. From the NAV - Main Menu, touch “New Destination,” then touch “Street Address.”

2. Once the Country and State are set and the Street Address screen is displayed, begin spelling the street name in the speller. In the upper right corner the number of possible roads decreases.

3. Touch the “LIST” soft-key to display a list of possible street names. Select the correct street name.

4. Next input the number.

Page 71

ELECTRONICS

5. In the Confirm Route screen the navigation radio displays the complete address, a map of the destination area, and the current routing method for you to verify.

6. Touch the “GO” soft-key to activate the route guidance.

Entering Your Home Location

1. Press the NAV hard-key on the right side of the radio.

2. From the NAV - Main Menu, touch “Guide Me Home” to enter your home address. If no home address has been set, touch “YES” to access the Enter Home Address menu.

3. Touch “Street Address” to enter your address. Touchthe soft-key with your state’s name and enter your street name into the speller.

4. Once the street name has been input, touch “CONTINUE” to confirm. Enter the house number into the next screen. Ifmore than one city has this address, you will then need to select your city from a list.

5. Once the address is entered completely, the system shows a map of your home address area. Touch “SAVE” to confirm the address. The system will then ask if you want to go there. Touch the “Yes” or “No” soft-key.

Change Home Address

NOTE:

This procedure will allow youto change your HomeAddressif one has alreadybeen entered. Entering the city or zip code before entering the street name facilitates address entry.

1. Press the MENU hard-key, touch “My Files” and then touch “My Address Book.”

2. Touch “Home”, then touch “Edit Contacts” and then “Change Address.”

3. Touch the soft-key with your state’s name and enter your street name into the speller.

4. Once the street name has been input, touch “CONTINUE” to confirm.

5. Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list.

6. Touch the “SAVE” soft-key to confirm the address.

Go Home

• From the NAV - Main Menu, touch “Guide Me Home” whenyou want to route to your home

destination.

Where Am I Now?

1. From the NAV - Main Menu, touch “Where Am I Now?” The Where Am I Now? menu

displays location information for the current vehicle position.

2. Touch the “NEARBY POI” soft-key to search for a local Point of Interest.

3. Touchthe “SAVELOCATION” soft-key to save the current location in the Saved Locations memory.

Page 72

ELECTRONICS

Route Guidance

• After starting route guidance, the system calculates the route and announces: “Follow the arrows on the display.” You will receive navigation recommendations by voice messages and screen displays.

Route Options

• After pressing the “OPTIONS” soft-key in the Route Guidance Menu, the following information is displayed:

• In the left half of the screen, the current position and the current routing method are

displayed.

• “ Take Detour” will allow you to calculate a different route.

• “Find Nearby POI” to search for a local POI.

• “Destination Info” displays destination information.

• “View Turn List” lists streets utilized for the current route.

• “Save Destination” to save the destination address.

• “Change Method” will allow you to change the routing method.

Page 73

ELECTRONICS

SiriusXM SATELLITE RADIO/TRAVEL LINK

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States.

• The following describes features that are available when in SiriusXM Satellite Radio mode.

• To access SiriusXM Satellite Radio, press the R ADIO/MEDIA or RADIO hard-key, then touch the “SAT” soft-key tab.

Info

• Touch the “i” soft-key to view detailed information about the current Sirius XM Satellite channel.

SiriusXM Parental Controls

• SiriusXM offers the option to permanently block selected channels. Call 1-888-539-7474 and request the Family Package.

• Uconnect® 430/430N and 730N: Press the “MENU” hard-key while in SiriusXM Satellite Radio Mode, then touch the “Channel Lock” to enable and/or disable desired channels. The SEEK and SCAN function will then only display channels without Channel lock.

Search/Browse

• Touch the “magnifying glass” soft-key to search/browse the SiriusXM channel listing by Favorites and Categories such as Song, Artist and Channel Name. The Search/Browse also allows you to manage your Favorites.

Page 74

ELECTRONICS

SiriusXM Satellite Radio Favorites (SAT Favorites)

• You can save 50 favorite songs and 50 favorite artists. Touch the “Add Favorite” soft-key to add

• either the song or the artist of the currently playing program to the SAT Favorites list. The favorite star will appear in the upper right corner, below the “SAT” soft-key.

• Youwill see a favorite star indicator in the upper right side of the screen below the “SAT” soft-key and a pop up will alert you that a favorite song or artist is currently playing on one of the SiriusXM satellite radio channels.

NOTE:

Refer to your Uconnect® 730N or 430/430N Supplement Manual for more information.

Display SAT Favorites List

• Touch the “Search/Browse” soft-key and select “Favorites” from the SAT Browse screen.

• Touch the desired favorites soft-key to switch the SAT tuner to thecorresponding channel.

• Youmay use the “LIST” soft-key to toggle between:

• Favorite Songs

• Favorite Artists

• Currently playing favorites

Page 75

ELECTRONICS

Replay

• While you are in SAT mode, you can replay 44 minutes of the current SiriusXM channel (when the channel is changed, this audio buffer is erased). Press the REPLAY button to listen to the stored audio.

• You can touch the on-screen controls to pause and rewind audio playback, touch the SCAN button to preview each of the tracks stored in the buffer, or select a track from the list.

• The time displayed below the bar indicates how much time is present between the current buffer play position and the live broadcast.

Replay Option Option Description

Play/Pause Touch to pause content playback. Touch Pause/Play again to resume

Rewind/RW Rewinds the channel content in steps of five seconds. Touch and hold to

Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However, Fast

Replay Time Displays the amount of time in the uppercenterof the screen by which your

Live Resumes playback of live content at any time while replaying rewound

playback.

rewind continuously, then release to begin playing content at that point.

Forward/FW can only be used when content has been previously rewound.

content lags the live channel.

content.

Page 76

ELECTRONICS

SiriusXM Travel Link (Uconnect® 730N & Uconnect® 430N Only)

• SiriusXM Travel Link brings a wealth of useful information into your vehicle and right to your fingertips.

• To access Travel Link, press the MENU hard-key, then the “Travel Link” soft-key.

1 – Favorites

2 – Forecast

3 – Ski Info 4 – Fuel Prices 5 – Movies 6 – Sports

NOTE:

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States.

View and storeyour favorite location, theater and sport teams for quick access.

View detailed weather conditions, forecasts and ski/snowboarding conditions at resorts.

View ski and snowboarding conditions at ski resorts. View detailed price information for fuel stations. View information on movies that are playing at theaters. View sports scores and upcoming events for all major sports.

Page 77

ELECTRONICS

STEERING WHEEL AUDIO CONTROLS

• The steering wheel audio controls are located on the rear surface of the steering wheel.

Right Switch

• Press the switch up or down to increase or decrease the volume.

• Press the button in the center to change modes AM/FM/CD/SAT.

Left Switch

• Press the switch up or down to search for the next listenable station or select the next or previous CD track.

• Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer.

iPod®/USB/MP3 CONTROL

• There are many ways to play music from iPod®/MP3 players or USB devices through your vehicle's sound system.

• The remote USB port, located within the upper glove compartment, allows you to plug an iPod® into the vehicle's sound system.

NOTE:

If equipped with the Uconnect® 730N, the USB port on the faceplate allows the same functions as the remote USB port.

Page 78

ELECTRONICS

• Non-Touchscreen Radios: To hear audio from devices connected to the USB port, press the “AUX” button on the radio faceplate.

• Touchscreen Radios: To hear audio from devices connected to the USB port, press the “MEDIA” hard-key, then touch the “AUX” or “iPod®” soft-key.

• When connected to this feature:

• The iPod® can be controlled using the

radio buttons to Play, Browse, and List the iPod® or external devices contents.

• The iPod® battery charges when

plugged into the USB port (if supported by the specific audio device).

• Compatible iPod® devices may also be

controllable using voice commands. Refer to the Owner's Manual on the DVD for details.

NOTE:

The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For suppor ted audio file formats, refer to the USB Port section in the Owner's Manual on the DVD. Refer to www.UconnectPhone.com for a list of tested iPod®s. Some iPod® software versions may not fully support the USB port features. Please visit Apple’s website for iPod® software updates.

WARNING!

Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision.

Uconnect® PHONE

Uconnect® Phone

• To determine if your vehicle is equipped with Uconnect® Phone, press the “Uconnect® Phone” button will hear a voiceprompt.If not, you will seea message on theradio “Uconnect® Phone not available.”

• The Uconnect® Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section).

located on the radio faceplate. If your vehicle has this feature, you

Page 79

ELECTRONICS

NOTE:

To access the tutorial, press the “Uconnect® Phone” button “tutorial.” Press any hard-key/buttonor touch the display (Touchscreen radio) to cancel the “tutorial.”

• The Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands.

• Refer to your vehicle Owner's Manual on the DVD for further details.

NOTE:

The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® Hands-Free Profile, Version 1.0 or higher. For Uconnect® Customer Support: U.S. residents - visit www.UconnectPhone.com or call 1–877–855–8400. Canadian residents - visit www.UconnectPhone.com or call, 1-800-465–2001 (English) or 1-800-387-9983 (French). This site will provide specific instructions based on the type of mobile phone being paired.

Phone Pairing

NOTE:

Pairing is a one - time initial setup before using the phone. Prior to starting the pairing procedure ensure all additional phones within the vehicle have their Bluetooth® disabled.

1. Press the “Phone”

2. Wait for the “ready” prompt and BEEP.

3. After the BEEP, say ”setup” or “Uconnect device setup.”

4. After the BEEP, say “device pairing.”

5. After the BEEP, say “pair a device.”

6. Follow the audible prompts.

• You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can say any four-digit PIN. You will not need to remember this PIN after the initial pairing process.

• You will then be prompted to give the phone pairing a name (each phone paired should have a unique name).

• Next you willbe asked to give this new pairinga priority of1 through 7 (upto seven phones may be paired); 1 is the highest and 7 is the lowest priority. The system will only connect to the highest priority phone that exists within the proximity of the vehicle.

• You will then need to start the pairing procedure on your cell phone. Follow the Bluetooth® instructions in yourcell phone Owner's Manual to complete thephone pairing setup.

button to begin.

. After the BEEP, say

Page 80

ELECTRONICS

Phonebook

Phonebook Download — Automatic Phonebook Transfer From Mobile Phone

• If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. Automatic Transfer is indicated by a green arrow at the bottom of the screen. See www.UconnectPhone.com for supported phones.

• Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone. For example, after you start the vehicle.

NOTE:

The mobile phone may require authorization prior to download.

• A maximum of 1000entries per phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone.

• Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previously downloaded phonebook is available for use.

• Only the phonebook of the currently connected mobile phone is accessible.

• Only the mobile phone’s phonebook is downloaded. The SIM card phonebook is not part of the Mobile phonebook.

• This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect® Phone on the next phone connection.

Making A Phone Call

• Press the “Phone” button .

• After the BEEP, say “dial” (or “call” a name).

• After the BEEP, say number (or name).

Receiving A Call — Accept (And End)

• When an incoming call rings/is announced on Uconnect®, press the “Phone” button

• To end a call, press the “Phone” button

Mute (Or Unmute) Microphone During Call

• During a call, press the “Voice Command” button .

• After the BEEP, say “mute” (or “mute off”).

Page 81

ELECTRONICS

Transfer Ongoing Call Between Handset And Vehicle

• During a call, press the “Voice Command” button .

• After the BEEP, say “transfer call.”

Changing The Volume

• Start a dialogue by pressing the “Phone” button , then adjust the volume during a normal call.

• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Uconnect® system is speaking. Please note the volume setting for Uconnect® is different than the audio system.

WARNING!

• Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Yourattention should be focused on safely operating the vehicle. Failure to do so may result ina collision causing you andothers to be severely injured or killed.

• In an emergency, to use Uconnect® Phone, your mobile phone must be:

• turned on,

• paired to Uconnect® Phone,

• and have network coverage.

Uconnect® VOICE COMMAND

Voice Command Operation

• The Uconnect® Voice Command system allows you to controlyour AM, FM radio, satellite radio, disc player, HDD, Uconnect® Phone, a memo recorder, and supported portable media devices.

• When you press the “Voice Command” button steering wheel, you will hear a beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options. If you ever want to interrupt the system while it lists options, press the “Voice Command” button

NOTE:

Visit http://www.driveuconnect.com/features/voiceCommand/ for more info on which voice command features apply to your vehicle.

, listen for the BEEP, and say your command.

located on the radio faceplate or

Page 82

ELECTRONICS

• Start a dialogue by pressing the “Voice Command” button , you will hear a beep. The beep is your signal to give a command. Below are a list of voice commands for each of the different modes.

Common Voice Commands (Examples)

While In: Voice Command Example:

“Radio AM” (to switch to the AM radio mode)

“Radio FM” (to switch to the FM radio mode)

“Satellite Radio” (to switch to the Satellite radio mode)

“Disc” (to switch to the disc mode)

Main Menu

Radio Mode

SiriusXM Satellite Radio

Mode

Disc Mode

“Bluetooth Streaming” (to switch to the Bluetooth® Streaming

“Channel Number” (to change the channel by its spoken number)

"Channel Name" (to change the channel by its spoken name)

“USB” (to switch to the USB mode)

mode)

“Memo” (to switch to the memo recorder)

“System Setup” (to switch to system setup)

“Frequency” (to change the frequency)

“Next Station” (to select the next station)

“Previous Station” (to select the previous station)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

“Next Channel” (to select the next channel)

“Previous Channel” (to select the previous channel)

“List Channel” (to hear a list of available channels)

“Select Name” (to say the name of a channel)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

“Track” (#) (to change the track)

“Next Track” (to play the next track)

“Previous Track” (to play the previous track)

“Main Menu” (to switch to the main menu)

Page 83

ELECTRONICS

While In: Voice Command Example:

To switch to the voice recorder mode, say “Memo.” The following

are common voice commands for this mode: “New Memo” (to

record a new memo) — During the recording, you may press the

Memo Mode

Voice Command button

— “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Command button to stop playing memos. You proceed by saying one of the follow-

by saying one of the following commands:

— “Save” (to save the memo)

— “Continue” (to continue recording)

— “Delete” (to delete the recording)

— “Repeat” (to repeat a memo)

— “Next” (to play the next memo)

— “Previous” (to play the previous memo)

— “Delete” (to delete a memo)

— “Delete All” (to delete all memos)

Voice Text Reply

• If equipped with Uconnect® VoiceCommand, your Uconnect® 430N / 730N radio may be able to play incoming Short Message Service (SMS) messages (text messages) through the vehicle's sound system.

• It also allows you to respond by selecting from various predefined phrases.

• Not all phones are compatible with this feature. Refer to the phone compatibility list at www.UconnectPhone.com. Connected mobile phones must be bluetooth-compatible and paired with your radio.

• Press the “Voice Command” button

NOTE:

To access the tutorial, press the “Voice Command” button “tutorial.” Press any hard-key/buttonor touch the display (Touchscreen radio) to cancel the tutorial.

and after the BEEP, say “SMS” to get started.

to stop recording. You proceed

ing commands:

. After the BEEP, say

WARNING!

Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed.

Page 84

ELECTRONICS

Bluetooth® STREAMING AUDIO

• If equipped with Uconnect® Voice Command, your Bluetooth®-equipped iPod® devices, cell phones or other media players, may also be able to stream music to your vehicles speakers. Your connected device must be Bluetooth®compatible, and paired with your radio (see www.UconnectPhone.com for pairing instructions).

• Non-Touchscreen Radios: Press the “AUX” button on the radio faceplate until "BT" or “Audio Streaming” is displayed on the radio screen.

• Touchscreen-Radios: Press the “RADIO/MEDIA”or “MEDIA”hard-key and then touch the “AUX” soft-key tab.

VIDEO ENTERTAINMENT SYSTEM (VES™)

System Operation

• The screen is located in the overhead compartment console. To lower the screen, press the release button located in the center of the console rear of the screen.

• The system may becontrolled by the front seat occupants using either the radio or DVD player controls, or by the rear seat occupants using the remote control.

• The video screen displays information in a split screen format. The left side of the screen is referred to as Channel 1 and the right side of the screen is referred to as Channel 2. All modes except video modes are displayed in a split screen format.

• To use the headphones, press the power button located on the right ear cup. Select the channel on the headphones (1 or 2) which corresponds to the channel selected on the desired video screen.

• To receive VES™ audio through the vehicle's sound system, press the VES™ soft-key on the radio's touchscreen.

Page 85

ELECTRONICS

Operation Of The Touchscreen Radio/DVD Player/Blu-Ray® Player

• To view a DVD press the OPEN/CLOSE or LOAD hard-key on the touchscreen radio and insert the disc or insert the disc into the optional DVD player. Playback will begin automatically after the DVD is recognized by the disc drive. If playback does not begin automatically when the disc is inserted into the DVD player press the PLAY button. If playback does not begin automatically after the disc is inserted into the touchscreen radio follow these steps:

• Press the MENU hard-key, then touch the RearVES™ soft-key.If a chapter list appears on the right side of the screen, touch the HIDE LIST soft-key to display the Rear VES™ control screen.

• Touch the 1 soft-key to select an audio channel, then touch the DISC soft-key in the MEDIA column.

Operation Of The Remote Control

• The remote control operates similarly to any DVD remote you may have used before and allows the rear seat passengers to change stations, tracks, discs and audio/video modes.

• The remote control is designed to control either channel by using the selector switch located on the right side of the remote.

• Connect the video game or other external media devices to the AUX jacks following the color coding for the VES™ jacks.

• Pressing the power button will turn the VES™ system ON/OFF.

• Pressing the mode button causes the MODE SELECTION menu to appear on the VES™ screen. Use the remote control arrow buttons to scroll through the available modes, and then press ENTER to select the desired mode.

Auxiliary Audio/ Video Input Jacks

• The AUX jacks are located on the drivers side rear trim panel behind the sliding door.

• Connect the video game or other external media devices to the AUX jacks following the color coding for the VES™ jacks.

• Using either the touchscreen radio or remote control, select AUX from the REAR VES™ CONTROL or the MODE SELECTION screen.

• Refer to the Uconnect® Multimedia – Video Entertainment System (VES™) section in the vehicle Owner's Manual on the DVD for further details.

Page 86

ELECTRONICS

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)

• The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the left side of the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to “Programmable Features” located in this guide.

• Press and release the UP scroll upward through the main menus (Fuel Economy, Vehicle Speed, Trip Info, Vehicle Info, Messages, Units, System Set-Up, Turn Menu Off) and sub menus.

• Press and release the DOWN sub menus.

• Press and release the SELECT select a personal setting in the setup menu.

• Press the BACK button to scroll back to a previous menu or sub menu.

Compass Calibration

This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.

You may also calibratethe compass by completingone or more 360 degreeturns (in an area free from large metal or metallic objects) until the “CAL” message displayed in the EVIC turns off. The compass will now function normally.

button to

button to scroll downward through themain menus and

button for access to main menus, sub menus or to

Page 87

ELECTRONICS

PROGRAMMABLE FEATURES

Electronic Vehicle Information Center (EVIC) — If Equipped

• Personal Settings allows you to set and recall features when the transmission is in PARK. If the transmission is out of PARK or the vehicle begins moving, a warning message SYSTEM SETUP NOT AVAILABLE VEHICLE NOT IN PARK displays when you try to select “System Setup” from the main menu.

• The EVIC can be used to program the following Personal Settings. Press and release the SELECT button scroll through the settings. Press the SELECT button

• Select Language • Key-Off Power Delay

• Nav-Turn By Turn • Illuminated Approach

• Auto Lock Doors • Hill Start Assist

• Auto Unlock Doors • Flashers with Sliding Door

• Remote Unlock Sequence • Calibrate Compass

• Remote Start Comfort Sys. • Compass Variance

• Horn with Remote Lock • Park Assist - If Equipped

• Flash Lamps With Lock • Automatic High Beams - If Equipped

• Headlamp Off Delay • Keyless Enter-N-Go - If Equipped

• Headlamps With Wipers • RKE Linked To Memory - If Equipped

Key Fob Programmable Features

The following features may also be programmed by using the Key Fob transmitter or the ignition switch and driver's door lock switch.

NOTE:

Pushing the LOCK button while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Push the UNLOCK button to deactivate the Vehicle Security Alarm.

Unlock On First Push

To unlock either the driver's side, or all doors, on the first push of the UNLOCK button:

• Push and hold the LOCK button for at least four seconds, but no longer than 10 seconds. Then, push and hold the UNLOCK button while still holding the LOCK button.

• Release both buttons at the same time.

until Personal Settings displays, then press the DOWN button to

to change the setting.

Page 88

ELECTRONICS

Auto Unlock Doors On Exit

To have all of the vehicle doors unlock when any door is opened:

• Enter your vehicle and close all the doors, and fasten your seat belt.

• Cycle the ignition switch between the LOCK and ON position four times, ending in the LOCK position (do not start the engine).

• Push the power door UNLOCK switch to unlock the doors. A singlechime will indicate that programming is complete.

Sound Horn With Lock

To turn the horn chirp on or off when the doors are locked:

• Push the LOCK button and PANIC button at the same time for at least four seconds, but no longer than 10 seconds.

• Release both buttons at the same time.

Flashing Lights With Lock

The turn signal lights flash when the doors are locked, which can be turned on or off. To turn this feature on or off:

• Push and hold the UNLOCKbutton and the LOCK button at the same time for at least four seconds, but no longer than 10 seconds.

• Release both buttons at the same time.

UNIVERSAL GARAGE DOOR OPENER (HomeLink®)

•

HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery.

• The HomeLink® buttons that are located in the overhead console or sunvisor designate the three different HomeLink® channels.

• The HomeLink® indicator is located above the center button.

Before You Begin Programming HomeLink®

Ensure that your vehicle is parked outside of the garage before you begin programming.

For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.

Page 89

ELECTRONICS

Erase all channels before you begin programming. To erase the channels, place the ignition switch into the ON/RUN position, then press and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds or until the red indicator flashes.

NOTE:

Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons.

If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at www.HomeLink.com for information or assistance.

Programming A Rolling Code

NOTE:

For programming Garage Door Openers that weremanufacturedafter 1995. These GarageDoor Openers can be identified by the “LEARN” or “TR AIN” button located where the hanging antenna is attached to the Garage Door Opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer.

1. Place the ignition switch into the ON/RUN position.

2. Place thehand-held transmitter 1 to 3in (3 to 8 cm)away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

4. Continue to hold both buttons and observe the indicator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.

5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly press and release the “LEARN” or “TRAINING” button.

NOTE:

You have 30 seconds in which to initiate the next step after the LEARN button has been pressed.

6. Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.

NOTE:

If the device does not activate, press the button a third time (for two seconds) to complete the training.

7. To program the remaining two HomeLink® buttons, repeat each step for each remaining

button. DO NOT erase the channels.

Page 90

ELECTRONICS

Programming A Non-Rolling Code

NOTE:

For programming Garage Door Openers manufactured before 1995.

1. Turn the ignition switch to the ON/RUN position.

2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

5. Press and hold the programmed HomeLink® buttonand observe theindicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink® button is pressed.

6. To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.

Using HomeLink®

• To operate, press and release the programmed HomeLink® button. Activation will now

occur for the programmed device (e.g., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time.

WARNING!

• Your motorized door or gate will open and close while you are programming the universal transceiver.Do not program the transceiver if people or pets are in the path of the door or gate.

• Do not run your vehicle in a closed garage or confined area while programming the transceiver. Exhaust gas from your vehicle contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous when inhaled and can cause you and others to be severely injured or killed.

Page 91

ELECTRONICS

POWER INVERTER

• There is a 115 Volt, 150 Watt power inverter outlet located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.

• Press the switch located in the center of the instrument panel to turn the power to the outlet on.

• Press the switch again to turn the power off.

• The status indicator of the AC power inverter indicates whether the inverter is producing AC power.

NOTE:

The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually, unplug the device and plug it in again. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter.

WARNING!

To Avoid Serious Injury or Death DO NOT:

• use a three-prong adaptor

• insert any objects into the receptacles

• touch with wet hands Close the lid when not in use. If this outlet is mishandled, it may cause an electric shock and failure.

Page 92

ELECTRONICS

POWER OUTLETS

•

Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel, below the open storage bin. The driver-side power outlet is controlled by the ignition switch and the passenger-side power outlet is connected directly to the battery. The driver-side power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker's Package).

• One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet.

• On vehicles equipped with the Super Console the power outlets are located under the retractable cover.Toaccess the poweroutlets push down on the cover and slide it toward the instrument panel.

• The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets.

Page 93

ELECTRONICS

NOTE:

• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced.

• Power outlets aredesigned for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle warranty.

Page 94

UTILITY

IN-FLOOR STORAGE — STOW'N GO®

Second Row Seat Storage Bins

• Storage bins are located in the floor in front of the second row seats that can be used when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the "Lock" position to allow greater access to the storage bin.

Cargo Area Storage

• The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

WARNING!

In a collision, serious injury could result if the seat storage bin covers are not properly latched. Do not drive the vehicle with the storage bin covers open. Keep the storage bin covers closed and latched while the vehicle is in motion. Do not use a storage bin latch as a tie down.

ROOF LUGGAGE RACK

• The crossbars on your vehicle are delivered stowed within the roof rack side rails. When installed, the roof rack can hold a maximum of 150 lbs (68 kg) of evenly distributed weight.

Installing The Crossbars

To install the crossbars, completely loosen

• the thumb screws at both ends and lift the crossbar from its stowed position.

• Bend the pivot points at each end of the crossbar and slide the thumbscrewdown.

• Set the crossbars into position and tighten the thumb screws.

NOTE:

Make sure the directional arrow on the crossbar aligns with the directional arrow on the side rail.

• Refer to the Owner's Manual on the DVD for further details.

1 — Directional Arrow 2 — Pivot Point 3 — Thumb Screw

Crossbar

Page 95

UTILITY

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)

Engine/

Transmission

3.6L/Automatic

* For vehicles equipped with Fold-in-Floor seating, the Gross Trailer Weight must be reduced

by 100 lbs (45 kg). Refer to local laws for maximum trailer towing speeds.

NOTE: The trailer tongue weight must be considered as part of the combined weight of

occupants and cargo, and should never exceed the weight referenced on the Tire and

GCWR (Gross

Combined Wt.

Rating)

8,750 lbs

(3,969 kg)

8,750 lbs

(3,969 kg)

8,750 lbs

(3,969 kg)

Loading Information placard.

Frontal Area

40 sq ft

(3.72sqm)

40 sq ft

(3.72sqm)

40 sq ft

(3.72sqm)

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)

Towing Condition Wheels OFF the Ground All Models

Flat Tow NONE

Dolly Tow

On Trailer ALL OK

Front OK

Rear

Max. GTW

(Gross Trailer

Wt.)

Up to 2 persons

& Luggage

3,600 lbs

(1,633 kg) *

3 to 5 persons &

Luggage

3,350 lbs

(1,519 kg) *

6 to 7 persons &

Luggage

3,000 lbs

(1,360 kg) *

NOT ALLOWED

Max. Tongue Wt.

360 lbs (163 kg)

335 lbs (152 kg)

300 lbs (136 kg)

Page 96

UTILITY

Recreational Towing — All Models

• Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure:

1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer's instructions.

2. Drive the front wheels onto the tow dolly.

3. Firmly apply the parking brake. Place the transmission in PARK.

4. Properly secure the front wheels to the dolly, following the dolly manufacturer's

instructions.

5. Release the parking brake.

CAUTION!

• DO NOT flat tow this vehicle. Damage to the drivetrain will result.

• Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.

Page 97

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE

Dial toll-free 1-800-521-2779 for U.S. Residents or 1-800-363-4869 for Canadian Residents.

• Provide your name, vehicle identification number, license plate number, and your location, including the telephone number from which you are calling.

• Briefly describe the nature of the problem and answer a few simple questions.

• Youwill be given the name of the service provider and an estimated time of arrival. If you feel you are in an “unsafe situation”, please let us know. With your consent, we will contact local police or safety authorities.

INSTRUMENT CLUSTER WARNING LIGHTS

- Electronic Stability Control (ESC) Indicator Light

If this indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road conditions. Toimprove the vehicle's traction when starting off in deep snow, sand or gravel, it may be desirable to switch the ESC system off.

- Tire Pressure Monitoring System (TPMS) Light

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system ( TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly,when the low tirepressuretelltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

IF THE LIGHT STARTS FLASHING INDICATING A LOW TIRE PRESSURE, ADJUST THE AIR PRESSURE IN THE LOW TIRE TO THE AIR PRESSURE SHOWN ON THE VEHICLE PLACARD OR TIRE INFLATION PRESSURE LABEL LOCATED ON THE DRIVER'S DOOR.

Page 98

WHAT TO DO IN EMERGENCIES

NOTE:

AFTER INFLATION, THE VEHICLE MAY NEED TO BE DRIVEN FOR 20 MINUTES BEFORE THE FLASHING LIGHT WILL TURN OFF.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.

When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occurfora variety of reasons,including the installation ofreplacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

NOTE:

Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature is 68°F (20°C) and the outside temperature is 32°F (0°C), then the coldtire inflation pressure should beincreased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is notof the same size, type, and/or style. Aftermarket wheelscan cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

Page 99

WHAT TO DO IN EMERGENCIES

- Engine Temperature Warning Light

• This light warns of an overheated engine condition.

• If the light turns on or flashes continuously while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.

• Werecommendthat you do not operatethe vehicle or engine damagewill occur.Have the vehicle serviced immediately.

WARNING!

A hot engine cooling system is dangerous. Youor others could be badly burned by steam or boiling coolant.

BRAKE

The Brake Warning light illuminates when there is either a system malfunction or the parking brake is applied. If the light is on and the parking brake is not applied, it indicates a possible brake hydraulic malfunction, brake booster problemor an Anti-Lock Brake System problem.

Please have your vehicle serviced immediately.

- Brake Warning Light

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.

- Malfunction Indicator Light (MIL)

Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles. In most situations, the vehicle will drive normally and not require towing.

If the MIL flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage. We recommend you do not operate the vehicle. Have the vehicle serviced immediately.

- Electronic Stability Control (ESC) OFF Indicator Light

This light indicates the Electronic Stability Control (ESC) is off.

Page 100

WHAT TO DO IN EMERGENCIES

- Charging System Light

This light shows the status of the electrical charging system. If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.

We recommend you do not continue driving if the charging system light is on. Have the vehicle serviced immediately.

- Oil Pressure Warning Light

This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on.

We recommend you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately.

- Anti-Lock Brake (ABS) Light

This light monitors the Anti-Lock Brake System (ABS).

If the light is not on during starting, stays on, or turns on while driving, we recommend you contact the nearest authorized dealer and have the vehicle serviced immediately.

- Electronic Throttle Control (ETC) Indicator Light

This light informs you of a problem with the system.

If a problem is detected, the light will come on while the engineis running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the PARKposition; the light should turn off.

If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer immediately. If the light is flashing when the engine is running, immediate service is requiredand you may experience reduced performance, an elevated/ rough idle or engine stall and your vehicle may require towing.

- Air Bag Warning Light

If the light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized dealer immediately.

Fuel Cap/Loose Gas Cap Message

If a “gas cap” message (shown as gASCAP) appears, tighten the gas cap until a “clicking” sound is heard.

Press the odometer reset button, located below the tachometer, to turn the message off.

If the message continues to appear for more than three days after tightening the gas cap, see your authorized service center.

Dodge Grand Caravan 2014 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

VEHICLES SOLD IN CANADA

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

CONTROLS AT A GLANCE

DRIVER COCKPIT

INSTRUMENT CLUSTER

Warning Lights

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors And Liftgate

Panic Alarm

Power Liftgate

Power Sliding Doors

Emergency Key

REMOTE START

VEHICLE SECURITY ALARM

To Arm:

To Disarm The System:

SEAT BELT

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

CHILD RESTRAINTS

LATCH — Lower Anchors And Tethers For CHildren

Installing The Child Restraints Using The Vehicle Seat Belts

To Install A Child Seat Using An ALR:

To Install A Child Seat Using A Cinching Latch Plate:

Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt):

FRONT SEATS

Power Seat

Power Lumbar

Manual Seat Adjustment

Memory Seat

REAR SEATS

Second Row Seats — Stow 'n Go®

Third Row Seats

HEATED SEATS

Front Heated Seats

Second Row Heated Seats

HEATED STEERING WHEEL

TILT/TELESCOPING STEERING COLUMN

ADJUSTABLE PEDALS

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER

Turn Signal/Lane Change Assist

Front Wipers

Rear Wiper

High Beams

Flash To Pass

HEADLIGHT SWITCH AND HALO LIGHT SWITCH

Automatic Headlights/Parking Lights/Headlights

Instrument Panel Dimmer

Overhead (Halo) Light

SPEED CONTROL

Cruise ON/OFF

Accel/Decel

Resume

Cancel

ELECTRONIC RANGE SELECTION (ERS)

FUEL ECONOMY (ECON) MODE

MANUAL CLIMATE CONTROLS

Air Recirculation

Heated Mirrors

Rear Window Defroster

THREE ZONE MANUAL CLIMATE CONTROLS

Air Recirculation

Heated Mirrors

Rear Window Defroster

Activating Rear Passenger Climate Controls

THREE ZONE AUTOMATIC TEMPERATURE CONTROLS (ATC)

Automatic Operation

Air Conditioning (A/C)

SYNC Temperature Button

Air Recirculation

Heated Mirrors