Dodge Grandcaravan 2013 Owner's Manual

Grand Caravan
OWNER’S MANUAL
2013
Information Provided by:
VEHICLES SOLD IN CANADA
Information Provided by:
With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore.
DRIVING AND ALCOHOL
Drunken driving is one of the most frequent causes of accidents.
Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
WARNING!
Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.
This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.
Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obliga­tion upon itself to install them on products previously manufactured.
Copyright © 2012 Chrysler Group LLC
SECTION PAGE
Information Provided by:
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
10
INTRODUCTION .............................................................3
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .............................9
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ............................123
UNDERSTANDING YOUR INSTRUMENT PANEL ..................................303
STARTING AND OPERATING .................................................457
WHAT TO DO IN EMERGENCIES ..............................................559
MAINTAINING YOUR VEHICLE ...............................................589
MAINTENANCE SCHEDULES .................................................641
IF YOU NEED CONSUMER ASSISTANCE ........................................649
INDEX ....................................................................661
1
2
3
4
5
6
7
8
9
10
Information Provided by:

INTRODUCTION

Information Provided by:
CONTENTS
INTRODUCTION ........................4
1
VEHICLE IDENTIFICATION NUMBER ........6
HOW TO USE THIS MANUAL ..............4
WARNINGS AND CAUTIONS ..............6
VEHICLE MODIFICATIONS/ALTERATIONS ....7
4 INTRODUCTION
Information Provided by:

INTRODUCTION

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
This Owner’s Manual has been prepared with the assis­tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instruc­tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referenc­ing and remain with the vehicle when sold.
When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni­cians and genuine parts, and cares about your satisfaction.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.
Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.
The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:
Information Provided by:
INTRODUCTION 5
1
6 INTRODUCTION
Information Provided by:

WARNINGS AND CAUTIONS

This Owners Manual contains WARNINGS against oper- ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears stamped on the right sliding door sill under the sill moulding and printed on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle regis­tration and title.
Vehicle Identification Number
INTRODUCTION 7
Information Provided by:

VEHICLE MODIFICATIONS/ALTERATIONS

Stamped VIN Location
NOTE: It is illegal to remove or alter the VIN.
WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
1
Information Provided by:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Information Provided by:
CONTENTS
A WORD ABOUT YOUR KEYS .............12
Wireless Ignition Node (WIN) .............12
KeyFob.............................13
Removing Key Fob From Ignition ..........14
Key-In-Ignition Reminder ................15
SENTRY KEY® .........................15
Replacement Keys .....................16
VEHICLE SECURITY ALARM — IF
EQUIPPED ............................17
Rearming Of The System .................18
To Arm The System .....................18
To Disarm The System...................18
Tamper Alert .........................19
Security System Manual Override ...........19
ILLUMINATED ENTRY — IF EQUIPPED ......20
REMOTE KEYLESS ENTRY (RKE) — IF
EQUIPPED ............................20
Using The RKE Transmitter ...............21
REMOTE STARTING SYSTEM — IF EQUIPPED . . .30
How To Use Remote Start ................31
2
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
DOOR LOCKS .........................35
Seat Belts In Passenger Seating Positions ......66
Manual Door Locks.....................35
Power Door Locks — If Equipped ..........37
WINDOWS ...........................39
Power Vent Windows — If Equipped ........39
Power Windows .......................40
SLIDING SIDE DOOR ....................44
Power Sliding Side Door — If Equipped ......45
Sliding Side Door Child Protection Lock ......49
LIFTGATE ............................52
Power Liftgate — If Equipped .............53
OCCUPANT RESTRAINTS ................56
Lap/Shoulder Belts ....................60
Automatic Locking Retractor Mode (ALR) — If
Equipped ............................67
Energy Management Feature ..............68
Seat Belt Pretensioners ..................68
Supplemental Active Head Restraints (AHR) . . .68
Enhanced Seat Belt Use Reminder System
(BeltAlert®) ..........................72
Seat Belts And Pregnant Women ...........73
Seat Belt Extender .....................74
Supplemental Restraint System (SRS) —
Air Bags ............................74
Air Bag System Components ..............76
Advanced Front Air Bag Features ...........77
Air Bag Deployment Sensors And Controls ....81
Information Provided by:
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
SAFETY TIPS .........................117
Event Data Recorder (EDR) ...............88
Child Restraints .......................89
COMMERCIAL CARGO VEHICLES (NO FACTORY
INSTALLED REAR SEATS) — IF EQUIPPED . . .113
Restraining Infants And Small Children In
Commercial Cargo Vehicles...............114
ENGINE BREAK-IN RECOMMENDATIONS . . .116
Transporting Passengers .................117
Exhaust Gas .........................117
Safety Checks You Should Make Inside The
Vehicle .............................118
Periodic Safety Checks You Should Make Outside
The Vehicle .........................120
2
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similarly to an ignition switch. It has four operating positions, three with detents and one that is spring-loaded. The detent positions are OFF, ACC, and ON/RUN. The START position is a spring-loaded momentary contact position. When released from the START position, the switch automatically returns to the ON/RUN position.
Wireless Ignition Node (WIN)
1 — OFF 2 — ACCESSORY 3 — ON/RUN 4 — START

Key Fob

Information Provided by:
The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi­tion. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.
The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the lower glove compartment. You can keep the emergency key with you when valet parking.
To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
2
Emergency Key Removal
NOTE: You can insert the double-sided emergency key
into the lock cylinder with either side up.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:

Removing Key Fob From Ignition

Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob.
NOTE: Power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature.
WARNING!
Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and push ignition button to place ignition in OFF position. When leaving the vehicle, always lock your vehicle.
Never leave children alone in a vehicle, or with access to an unlocked vehicle.
(Continued)
WARNING! (Continued)
Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil­dren should be warned not to touch the parking brake, brake pedal or the shift lever.
Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.
Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
CAUTION!
An unlocked car is an invitation to thieves. Always remove the Key Fob from the ignition and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

Information Provided by:
Opening the driver’s door when the Key Fob is in the ignition and the ignition switch position is OFF or ACC, a chime will sound to remind you to remove the key.
NOTE: The Key-In-Ignition reminder only sounds when the Key Fob is placed in the OFF or ACC ignition position.

SENTRY KEY®

The Sentry Key® Immobilizer system prevents unauthor­ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
The system uses Key Fob with factory-mated Remote Keyless Entry (RKE) transmitter and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine.
After turning the ignition switch to the ON/RUN posi­tion, the Vehicle Security Light will turn on for three sec­onds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid Key Fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 sec­onds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
CAUTION!
The Sentry Key® Immobilizer system is not compat­ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be reprogrammed to any other vehicle.
CAUTION!
Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended.
At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs. Duplication of Key Fobs may be performed at an autho­rized dealer, this procedure consists of programming a blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.
NOTE: When having the Sentry Key® Immobilizer sys­tem serviced, bring all vehicle Key Fobs with you to the authorized dealer.
Customer Key Programming
Information Provided by:
Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.
General Information
The Sentry Key® system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:
This device may not cause harmful interference.
This device must accept any interference that may be
received, including interference that may cause unde­sired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

VEHICLE SECURITY ALARM — IF EQUIPPED

The Vehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau­thorized operation. When the alarm is activated, the interior switches for door locks, power sliding doors and power liftgate are disabled. The Vehicle Security Alarm provides both audible and visible signals, for the first three minutes, the headlights will turn on, the park lamps and/or turn signals will flash and Vehicle Security Light will flash repeatedly and the horn will sound. For an additional 15 minutes, only the headlights, park lamps and/or turn signals and Vehicle Security Light will flash.
2
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:

Rearming Of The System

The Vehicle Security Alarm will rearm itself after the 15 additional minutes of headlights and Vehicle Security Light flashing, if the Vehicle Security Alarm has not been disabled. If the condition which initiated the alarm is still present, the Vehicle Security Alarm will ignore that condition and monitor the remaining doors and ignition.

To Arm The System

Follow these steps to arm the Vehicle Security Alarm:
1. Remove the key from the ignition system (refer to
Starting Proceduresin Starting And Operatingfor further information).
Make sure the vehicle ignition system is OFFand the key is physically removed from the ignition.
2. Perform one of the following methods to lock the vehicle:
Press LOCK on the interior power door lock switch
with the driver and/or passenger door open.
Press the LOCK button on the Remote Keyless Entry
(RKE) transmitter.
3. If any doors are open, close them.

To Disarm The System

The Vehicle Security Alarm can be disarmed using any of the following methods:
Press the UNLOCK button on the Remote Keyless
Entry (RKE) transmitter.
Cycle the vehicle ignition system out of the OFF
position. Insert a valid key into the ignition switch and turn the key to the ON position.
NOTE:
Information Provided by:
The driver’s door key cylinder and the liftgate button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm.
The Vehicle Security Alarm remains armed during power liftgate entry. Pressing the liftgate button will not disarm the Vehicle Security Alarm. If someone enters the vehicle through the liftgate and opens any door the alarm will sound.
When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.
The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previ­ously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.
If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound. If this occurs, disarm the Vehicle Security Alarm.

Tamper Alert

If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times and the exterior lights blink three times when you unlock the doors. Check the vehicle for tampering.

Security System Manual Override

The Vehicle Security Alarm will not arm if you lock the doors using the manual door lock plunger.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:

ILLUMINATED ENTRY — IF EQUIPPED

The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.
This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for fur­ther information.
The lights will fade to off after approximately 30 seconds, or they will immediately fade to off once the ignition switch is turned to ON/RUN from the OFF position.
NOTE:
The front courtesy overhead console and door cour­tesy lights will not turn off if the dimmer control is in the “Dome ON” position (rotate horizontal thumb wheel on the bottom of the switch to the far right detent position).
The illuminated entry system will not operate if the dimmer control is in the “Dome OFF” position (rotate horizontal thumb wheel on the bottom of the switch to the far left detent position).

REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED

This system allows you to lock or unlock the doors and liftgate, and activate the Panic Alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
NOTE: Inserting the Key Fob with RKE transmitter into
Information Provided by:
the ignition switch disables the system from responding to any button presses from that RKE transmitter. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmitter buttons for all RKE transmitters.
Two RKE transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three-button RKE trans­mitters, and those built with power options will be equipped with up to seven-button RKE transmitters.

Using The RKE Transmitter

Three-button RKE transmitters will provide basic UN­LOCK, LOCK and PANIC functions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2
Key Fob With Three-Button RKE Transmitter
Seven-button RKE transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to operate the power liftgate (optional), power sliding doors, Remote Start feature
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
(optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK.
Key Fob With Seven-Button RKE Transmitter
Remote Unlock Doors And Liftgate
Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s side or twice to unlock all doors and liftgate. This will also turn on the Illuminated Entry system.
Remote Key Unlock On First Press
This feature lets you program the system to unlock either the driver’s side, or all doors, on the first press of the UNLOCK button on the RKE transmitter:
NOTE:
For vehicles equipped with an Electronic Vehicle Infor-
mation Center (EVIC), refer to “Electronic Vehicle Infor­mation Center (EVIC)/Personal Settings (Customer­Programmable Features)” in “Understanding Your Instrument Panel” for further information.
For vehicles not equipped with the EVIC, the Remote
Information Provided by:
Unlock feature can be enabled or disabled by perform­ing the following steps:
1. Perform this operation while standing outside the vehicle.
2. Press and hold the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the UNLOCK button while still holding the LOCK button.
3. Release both buttons at the same time.
4. Test the feature while outside of the vehicle by press­ing the LOCK/UNLOCK buttons on the RKE trans­mitter with the ignition switch in the OFF position and the Key Fob removed.
5. Repeat these steps if you want to return this feature to its previous setting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
NOTE: Pressing the LOCK button on the RKE transmit­ter while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.
Remote Lock Doors And Liftgate
Press and release the LOCK button on the RKE transmit­ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
Sound Horn With Remote Lock
This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows:
For vehicles equipped with the EVIC, refer to “Elec-
tronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Un­derstanding Your Instrument Panel” for further infor­mation.
For vehicles not equipped with the EVIC, perform the
following steps:
1. Perform this operation while standing outside the vehicle.
2.
Press the LOCK button on a programmed RKE trans­mitter for at least 4 seconds, but no longer than 10 sec­onds. Then, press the PANIC button while still holding the LOCK button.
3. Release both buttons at the same time.
4. Test the feature while outside of the vehicle by press­ing the LOCK button on the RKE transmitter with the ignition switch in the OFF position and the Key Fob removed.
5. Repeat these steps if you want to return this feature to its previous setting.
NOTE: Pressing the LOCK button on the RKE transmit­ter while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.
Using The Panic Alarm
Information Provided by:
To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
The Panic Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle is driven above 5 mph (8 km/h).
NOTE:
When you turn off the Panic Alarm by pressing the PANIC button a second time, you may have to move closer to the vehicle due to the Radio Frequency (RF) noises of the system.
The Panic Alarm cannot be activated if the engine is running.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
Power Open/Close Power Liftgate — If Equipped
Press the LIFTGATE button twice on the RKE transmitter within five seconds to Open/Close the Power Liftgate. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position.
The power liftgate may also be opened and closed by pressing the LIFTGATE button located on the overhead console.
If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. The liftgate cannot be opened from this switch.
If the vehicle is locked and Vehicle Security Alarm is armed, using RKE transmitter to open the power liftgate does not unlock the vehicle or disarm the Vehicle Security Alarm.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
Power Open/Close Left Power Sliding Door — If Equipped
Press the LEFT Power Sliding Door button twice on the RKE transmitter within five seconds to Power Open/ Close the Left Power Sliding Door. If the button on the RKE transmitter is pushed while the door is being power-closed, the door will reverse to the full open position.
Power Open/Close Right Power Sliding Door — If Equipped
Press the RIGHT Power Sliding Door button twice on the RKE transmitter within five seconds to Power Open/ Close the Right Power Sliding Door. If the button on the RKE transmitter is pushed while the door is being power-closed, the door will reverse to the full open position.
If the vehicle is locked and the Vehicle Security Alarm is armed, pressing the LEFT Power Sliding Door button twice unlocks the power sliding door and disarms Ve­hicle Security Alarm.
If the vehicle is locked and the Vehicle Security Alarm is armed, pressing the RIGHT Power Sliding Door button twice unlocks the power sliding door and disarms Ve­hicle Security Alarm.
Turn Off Flash Lights With RKE Lock — If Equipped
Information Provided by:
This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit­ter. This feature can be turned on or turned off. To change the current setting, proceed as follows:
For vehicles equipped with the EVIC, refer to “Electronic
Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
For vehicles not equipped with the EVIC, perform the following steps:
1. Perform this operation while standing outside the
vehicle.
2. Press and hold the UNLOCK button on a programmed
RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
3. Release both buttons at the same time.
4. Test the feature while outside of the vehicle by press­ing the LOCK/UNLOCK buttons on the RKE trans­mitter with the ignition switch in the OFF position and the Key Fob removed.
5. Repeat these steps if you want to return this feature to its previous setting.
NOTE: Pressing the LOCK button on the RKE transmit­ter while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.
2
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
Programming Additional Transmitters
If you do not have a programmed RKE transmitter, contact your authorized dealer for details.
Transmitter Battery Replacement
The recommended replacement battery is one CR2032 battery.
NOTE:
Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Do not touch the battery terminals that are on the back housing or the printed circuit board.
1. Remove the emergency key by sliding the mechanical
latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.
Emergency Key Removal
2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
Loading...
+ 653 hidden pages