Dodge Challenger Quick Reference Guide

2018

CHALLENGER

QUICK

REFERENCE

GUIDE

INCLUDES SRT 392/SRT HELLCAT

PASSIVE ENTRY

Keyless Enter-N-Go — Passive Entry

The Keyless Enter-N-Go system is an enhance­ment to the vehicle’s key fob. This feature allows
you to lock and unlock the vehicle’s door(s) and
liftgate without having to press the key fob lock or
unlock buttons.

To Unlock From The Driver Or Passenger Side

Grab The Door Handle To Unlock

• With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of
the driver or passenger side door handle, grab
either front door handle to unlock the door
automatically.

To Lock The Vehicle

• Both front door handles have buttons located
on the outside of the handle. With one of the
vehicle's Keyless Enter-N-Go key fobs located
outside the vehicle and within 5 ft (1.5 m) of
the driver's or passenger front door handle,
push the door handle button to lock the two
doors and trunk.

• Do NOT grab the door handle, when pushing
the door handle button. This could unlock the
door(s).

Push The Button To Lock

Do NOT Grab The Handle When Locking

NOTE:

• If “Unlock All Doors 1st Press” is programmed,
all doors will unlock when you grab hold of the
front driver's door handle. Additionally, all
doors and the trunk will unlock with this option
programmed when you push the trunk button.

• If a key fob is detected in the vehicle when
locking the vehicle using the power door lock
switch, the doors and trunk will unlock, and the
horn will chirp three times. On the third at­tempt, your key fob can be locked inside the
vehicle.

• After pushing the Keyless Enter-N-Go lock but­ton, you must wait two seconds before you can
lock or unlock the vehicle using the door
handle. This is done to allow you to check if the
vehicle is locked by pulling the door handle
without the vehicle reacting and unlocking.

• If a Keyless Enter-N-Go door handle has not
been used for 72 hours, the Keyless Enter­N-Go feature for that handle may time out.
Pulling the deactivated front door handle will
reactivate the door handle's Keyless Enter­N-Go feature.

To Enter The Trunk

Trunk Release Button

• With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of
the deck lid, push the button located on the
center of the light bar which is located on the
deck lid above the license plate.

For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana­dian Residents).

INSTRUMENT CLUSTER DISPLAY

Instrument Cluster Display

The instrument cluster display features an inter­active driver display that is located in the instru­ment cluster. Pushing the controls on the left side
of the steering wheel allows the driver to select
vehicle information and Personal Settings.

Instrument Cluster Display Controls

• Push the up button toscroll upward through the

main menus (Speedometer, mph/km/h, Vehicle
Info, Performance Pages – SRT only, Driver
Assist, Fuel Economy, Trip A, Trip B, Audio,
Stored Messages, Screen Set Up).

• Push the down button to scroll downward

through the main menuand submenus (Speed­ometer, mph/km/h, Vehicle Info, Driver Assist,
Fuel Economy, Trip A, Trip B, Audio, Stored
Messages, Screen Set Up).

• Push the right button to access the information

screens or submenu screens of a main menu
item.

• Push the left button to access the information

screens or submenu screens of a main menu
item.

• Push the OK button to access/select the infor-

mation screens or submenu screens of a main
menu item. Push and hold the OK button for
two seconds to reset displayed/selected fea­tures that can be reset. Pushing OK button will
also toggle between mph and km/h on the
digital speedometer.

Compass Calibration

This compass is self-calibrating, which eliminates
the need to set the compass manually. When the
vehicle is new, the compass may appear erratic,
and the cluster will display dashes (- -) until the
compass is calibrated.

You may also calibrate the compass by completing
one or more 360 degree turns (in an area free from
large metal or metallic objects) until the dashes (- -)
displayed in the cluster turn off. The compass will
now function normally.

For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana­dian Residents).

PHONE PAIRING

Pairing Procedure

Mobile phone pairing is the process of establish­ing a wireless connection between a cellular
phone and the Uconnect system.

Start Pairing Procedure On The Radio

Uconnect 4 With 7-inch Display

Uconnect 4 With 7-Inch Display

1. Place the ignition in the ACC or ON position.

2. Press the “Phone” button.

3. Select “Settings.”

4. Select “Paired Phones.”

5. Select “Add device.”

•

Uconnect Phone will display an “In progress”
screen while the system is connecting.

Uconnect 4C & 4C NAV With 8.4-inch Display

Uconnect 4C & 4C NAV With 8.4-Inch Dis-

1. Place the ignition in the ACC or ON position.

2. Press the “Phone” button in the Menu Bar on
the touchscreen.

3. Select “Pairing.”

4. Select “Paired Phones And Audio Devices.”

play

5. Select “Add Device.”

•

Uconnect Phone will display an “In prog­ress” screen while the system is connecting.

Pair Your iPhone:

Bluetooth On/Uconnect Device