D Link WL8620APA1, WL8620APEA1 User Manual
Quick Installation Guide
Unified AC Concurrent Dual-Band PoE Access Point
This document will guide you through the
basic installation process for your new D-Link
Unified Wireless Access Point.
DWL-8620AP/DWL-8620APE
Quick Installation Guide
Documentation is also available
on the D-Link website
2 D-Link DWL-8620AP(E) Quick Install Guide
POWER
When this LED is red,
the access point is
booting up. When it is
green, it is ready for
use.
LAN1/LAN2
When this LED is lit, the
device’s Ethernet port is
connected to an active
router or switch. The
light will flash when data
is being transmitted
through the port.
2.4GHz/5GHz
When the LED is lit, the
access point’s wireless
radio is enabled. It will
flash when data is being
transmitted via wireless.
ENGLISH
About This Guide
This installation guide provides basic
instructions for installing the DWL8620AP(E) Unified AC Concurrent Dual-Band
PoE Access Point on your network. For
additional information about how to use the
access point, please see the User Manual,
which is available on the CD included in
this package or from the D-Link support
website.
System Requirements
- CD-ROM drive
- Windows®, Macintosh®, or Linux-based
operating system
- An available Ethernet port
- Internet Explorer 11, Safari 7, Firefox 28,
Google Chrome 33 or higher
Unpacking the Product
Open the shipping carton and carefully
unpack its contents. Please consult the
packing list below to make sure all items
are present and undamaged. If any item is
missing or damaged, please contact your
local D-Link reseller for replacement.
- DWL-8620AP(E)
- Power adapter*
- Detachable Antenna*
- Mounting ring
- Console cable*
- CD-ROM
- Ceiling bracket (3 sets, sizes are 9/16",
14/16", and 1 1/2")
*The power adapter is an optional
accessory and not included in the
package in some regions. To power the
units, use a D-Link PoE switch or the
D-Link DPE-301GI PoE injector.
*The detachable Antenna is only for
DWL-8620APE
*The console cable is an optional
accessory and not included in the package in
Armenia, Azerbaijan, Belarus, Georgia, Israel,
Kaliningrad, Kazakhstan, Kyrgyzstan, Latvia,
Lithuania, Moldova, Mongolia, Russia, Turkey,
Turkmenistan, Ukraine, and Uzbekistan. If a
cable is required, please contact your reseller
to order it (Model: ACS-AP-CONSOLE).
Optional Accessories
- PoE Injector (Model: DPE-301GI)
Note: These accessories are not included
in the package. If any of these items are
required, please contact your reseller to
order it.
Hardware Overview
LEDs
Figure 1. DWL-8620AP LEDs
D-Link DWL-8620AP(E) Quick Install Guide 3
Interfaces
ENGLISH
Figure 2. DWL-8620AP Rear Panel
Configure the Access Point
To set up and manage the DWL-8620AP,
use one of the following methods:
• Manage the access point from
the computer: Connect the access
point and your computer directly via a
straight-through Ethernet cable. Ensure
your computer is configured with a static
IP address in the 10.90.90.0/24 subnet.
Launch a web browser, type the default
IP address of the access point
(http://10.90.90.91), then press Enter.
To log in, use the default login
information:
Username: admin
Password: admin
Installation
Power on the Access Point
To power on the DWL-8620AP, you can use
one of the following methods:
• Connect the supplied power adapter.
OR
• Plug one end of an Ethernet cable into
the LAN 1 port of the DWL-8620AP
and the other end into a port on a PoE
switch or injector.
DWL-8620AP Computer
• Manage the access point from the
computer via the switch or router:
Connect the access point and your
computer to the same switch or router.
If the access point did not acquire an
IP address from a DHCP server on
the network, enter 10.90.90.91 in the
address field of your browser, which
is the default IP address of the access
point. If you used a DHCP server on your
network to automatically configure
network information for the access point,
enter the new IP address of the access
point into the web browser. To log in, use
the default login information:
Username: admin
Password: admin
DWL-8620AP
Switch or
Router
Computer
4 D-Link DWL-8620AP(E) Quick Install Guide
• Manage the access point from the
ENGLISH
computer via the Unified Wireless
Switch or Wireless Controller:
Connect the access point to a Unified
Wireless Switch or Wireless Controller.
Connect your computer to the same
network as that of the Unified Wireless
Switch or Wireless Controller. Log in
to the Unified Wireless Switch web
administration page or Wireless
Controller web administration page. For
Warning: The DWL-8620AP is designed to
receive PoE power only from an 802.3atcompliant source, or from a D-Link-approved
power adapter. Connecting an access point
to a Power over Ethernet (PoE) device that is
not approved by D-Link can damage the
equipment.
Warning: This product is to be connected
only to indoor PoE networks with no outdoor
cable routing.
the default login information please see
Unified Wireless Switch user manual or
Wireless Controller user manual.
DWL-8620AP
Unified Wireless
Switch
or
Wireless Controller
Computer
Mounting Using Anchor
Screws
Installation
1. Place the plastic wall mounting ring on a
wall or ceiling. Mark the points where you
will insert the screws, then remove the
mounting ring.
2. Drill holes in the marked points and
Mounting Options
You can mount the DWL-8620AP access
point on any of the following types of
insert the plastic wall anchors.
3. Use the supplied screws to attach the
mounting ring to the wall.
surfaces:
• Solid surface wall or ceiling
• Tabletop
Cable Requirement
Use a CAT 5 cable with an even sheath.
The Ethernet ports on the DWL-8620AP
access point cannot accept a CAT 5 cable
that has an uneven sheath; the RJ-45
connector on the cable will not fit properly into
the receptacle on the access point.
Wall Installation Recommendations
4. Plug the CAT 5 cable into the LAN port on
the access point.
If you plan to install the DWL-8620AP on a
wall or other vertical surfaces, orient the top
of the access point (the side with the LEDs)
toward the intended coverage area. The
radio antennas transmit through the top of
the access point but not through the bottom
(where the bracket is).
D-Link DWL-8620AP(E) Quick Install Guide 5
ENGLISH
Ceiling crossbar
Ceiling bracket
5. To attach the access point to the
mounting ring, first locate the right side
of the access point that has a small lock
symbol on it, and make sure to line up
this side with the side of the mounting
ring that has Open - Lock written on it.
6. Twist clockwise to lock the access point
onto the ring. The lock symbol on the
access point must point directly to the
Close text on the mounting ring.
Mounting Using Ceiling
Bracket
Installation
1. Clip two ceiling brackets on the ceiling
panels. Make sure both bracket are
parallel.
2. Use the provided screws to attach the
mounting ring to the ceiling bracket.
3. Plug the CAT 5 cable into the LAN port on
the access point.
4. Place the DWL-8620AP onto the
mounting ring and rotate the device
clockwise to lock it in position.
6 D-Link DWL-8620AP(E) Quick Install Guide
Regulatory Statements
ErP Power Usage
This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and
automatically switches to a power-saving Network Standby mode within 1 minute of no packets
being transmitted. It can also be turned off through a power switch to save energy when it is not
needed.
Network Standby: 7.2692 watts
Switched Off: 0.073 watts
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)
This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
D-Link DWL-8620AP(E) Quick Install Guide 7
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For
product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Note:
The country code selection is for non-USA models only and is not available to all USA models. Per
FCC regulations, all WiFi product marketed in the USA must be fixed to USA operational channels
only.
RF Frequency Requirements
This device is for indoor use only when using all channels in the
5.150 GHz - 5.250 GHz, , 5.725 GHz - 5.850 GHz
frequency range. High power radars are allocated as primary users of the
5.150 GHz - 5.250 GHz, , 5.725 GHz - 5.850 GHz
bands.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 37 cm
between the radiator and your body.
Industry Canada statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS-310 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est
soumise à la condition que cet appareil ne provoque aucune interférence nuisible.
8 D-Link DWL-8620AP(E) Quick Install Guide
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction
avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui
ont été testées.
The County Code Selection feature is disabled for products marketed in the US/ Canada.
La fonction de sélection de l'indicatif du pays est désactivée pour les produits
commercialisés aux États-Unis et au Canada.
Caution :
i. the device for operation in the band 5150–5250 MHz is only for indoor use to
ii. for devices with detachable antenna(s), the maximum antenna gain permitted
iii. where applicable, antenna type(s), antenna models(s), and worst-case tilt
iv. users should also be advised that high-power radars are allocated as primary
Avertissement:
i. les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés
ii. pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne
iii. lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de
iv. users should also be advised that high-power radars are allocated as primary
reduce the potential for harmful interference to co-channel mobile satellite
systems;
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate;
angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in section 6.2.2.3 shall be clearly indicated.
users (i.e. priority users) of the bands and 5650-5850 MHz and that these
radars could cause interference and/or damage to LE-LAN devices.
uniquement pour une utilisatin à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux
permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être
conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester
conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation,
énoncée à la section 6.2.2.3, doivent être clairement indiqués.
users (i.e. priority users) of the bands and 5650-5850 MHz and that these
radars could cause interference and/or damage to LE-LAN devices.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0.43 m between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
Loading...