D Link DIR605B1 User Manual
Table of Contents
Table of Contents
Package Contents ....................................................... 4
System Requirements
Features
Hardware Overview
Connections
LEDs
Installation.................................................................... 8
Before you Begin
Wireless Installation Considerations
Wall Mounting Your Device
Connect to Cable/DSL/Satellite Modem
Connect to Another Router
Configuration.............................................................14
Web-based Configuration Utility
Setup Wizard
Internet Setup
.................................................................. 5
....................................................... 6
.................................................................. 7
..................................................... 8
................................................... 15
Static (assigned by ISP)
Dynamic
PPPoE
PPTP
L2TP
Dual Access (for Russia only)
....................................................... 20
......................................................... 21
............................................................ 22
............................................................. 23
............................................. 4
................................................. 6
........................ 9
................................... 10
................ 11
.................................... 12
............................ 14
............................... 19
.................................................. 20
...................... 24
LAN Setup
DHCP Server Settings
Time and Date
Parental Control
Port Forwarding
Application Rules
Access Control
Firewall & DMZ
Advanced Wireless
Advanced Network
Advanced Network
Routing
Device Administration
Save and Restore
Firmware Update
DDNS Setting
System Check
Schedules
Log Settings
Device Info
................................................................... 50
Log
Statistics
Active Session
....................................................... 31
..................................... 32
................................................. 33
............................................... 34
............................................... 35
............................................. 36
................................................. 37
................................................ 38
.......................................... 39
........................................... 40
........................................... 40
............................................................ 41
...................................... 42
............................................ 43
............................................. 44
.................................................. 45
.................................................. 46
........................................................ 47
..................................................... 48
....................................................... 49
.......................................................... 51
................................................ 51
Wireless Setup
................................................. 25
2D-Link DIR-615 User Manual
Table of Contents
Wireless ........................................................... 52
Help
................................................................. 53
Wireless Security....................................................... 54
What is WEP?
Configure WEP
What is WPA?
Configure WPA-PSK and WPA2-PSK
Configure WPA/WPA2-PSK
....................................................... 54
...................................................... 55
....................................................... 56
................... 57
.................................. 58
Configure WPA, WPA2, and WPA/WPA2 (RADIUS)
.............................................................................. 59
Connect to a Wireless Network................................ 60
®
Using Windows
Configure WEP
Configure WPA-PSK
XP............................................... 60
...................................................... 61
............................................. 63
Setting Up Wi-Fi Protection......................................65
Connecting to an Unsecured Wireless Network..... 81
Troubleshooting
........................................................ 85
Wireless Basics ......................................................... 89
What is Wireless?
........................................................................ 92
Tips
Wireless Modes
.................................................. 90
..................................................... 93
Networking Basics .................................................... 94
Check your IP address
Statically Assign an IP address
.......................................... 94
............................. 95
Technical Specifications........................................... 96
Warranty.....................................................................98
(WCN 2.0 in Windows Vista).....................................65
Initial Router Configuration for Wi-Fi Protection
Setting Up a Configured Router
............................ 66
.... 65
Changing the Computer Name and Joining a
Workgroup
................................................................. 67
Configuring the IP Address in Vista ........................ 69
Setting Up a Connection or Network Wirelessly .... 72
Connecting to a Secured Wireless Network (WEP,
WPA-PSK & WPA2-PSK)
........................................... 77
3D-Link DIR-615 User Manual
Section 1 - Product Overview
• D-Link DIR-615 Wireless Router
• Power Adapter
• Ethernet Cable
• Manual and Warranty on CD
Note: Using a power supply with a different voltage rating than the one included
with the DIR-615 will cause damage and void the warranty for this product.
Package Contents
Note: Always attach the power cord plug to the power supply, before inserting
the power cord and connected power supply to the wall outlet.
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows
adapter
• Internet Explorer 6 or Firefox 2.0 or above (for configuration)
®
, Macintosh®, or Linux-based operating systems with an installed Ethernet
4D-Link DIR-615 User Manual
Section 1 - Product Overview
• Faster Wireless Networking - The DIR-615 provides up to 300Mbps* wireless connection with other
802.11n wireless clients. This capability allows users to participate in real-time activities online, such as
video streaming, online gaming, and real-time audio.
• Compatible with 802.11b and 802.11g Devices - The DIR-615 is still fully compatible with the IEEE
802.11b and IEEE 802.11g standard, so it can connect with existing 802.11b and IEEE 802.11g PCI,
USB and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Content Filtering - Easily applied content filtering based on MAC Address, URL, and/or
Domain Name.
Features
• Filter Scheduling - These filters can be scheduled to be active on certain days or for a
duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The DIR-615 can pass through VPN sessions. It
supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-615
can securely access corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-615 lets you
control what information is accessible to those on the wireless network, whether from the Internet or from
your company’s server. Configure your router to your specific settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
5D-Link DIR-615 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
Pressing the Reset Button restores
the router to its original factory
default settings.
Receptor for the Power Adapter.
LAN Ports
Connect Ethernet devices such as
computers, switches, and hubs.
The Auto MDI/MDIX WAN
port is the connection for
the Ethernet cable to the
Cable or DSL modem.
6D-Link DIR-615 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
INTERNET
A solid light indicates connection
on the WAN port. This LED blinks
during data transmission.
Power LED
A solid light indicates a proper
connection to the power supply.
WLAN LED
A solid light indicates that the wireless
segment is ready. This LED blinks during
wireless data transmission.
Local Network LEDs
A solid light indicates a connection to an
Ethernet-enabled computer on ports 1-4.
This LED blinks during data transmission.
7D-Link DIR-615 User Manual
Section 2 - Installation
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the
router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Before you Begin
Please configure the router with the computer that was last connected directly to your modem. Also, you can only use
the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off
your modem, disconnect the USB cable and connect an Ethernet cable to the WAN port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as
WinPoet, Broadjump, or Ethernet 300 from your computer or you will not be able to connect to the Internet.
8D-Link DIR-615 User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within
the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of
walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business. The key
to maximizing wireless range is to follow these basic guidelines:
Keep the number of walls and ceilings between the D-Link router and other network devices to a
1.
minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position
your devices so that the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet
(14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on
range. Try to position access points, wireless routers, and computers so that the signal passes through
drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water
(fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4.
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate RF noise.
If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and
5.
home security systems), your wireless connection may degrade dramatically or drop completely. Make
sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.
9D-Link DIR-615 User Manual
Section 2 - Installation
Connect to Cable/DSL/Satellite Modem
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
WAN port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on
your computer.
5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router
to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, WAN light, and the LAN light (the port that your computer is
plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable
connections are correct.
9. Skip to page 16 to configure your router.
11D-Link DIR-615 User Manual
Section 2 - Installation
Connect to Another Router
If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have
to do the following before connecting the router to your network:
• Disable UPnP
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot
accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1.
Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable.
Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the
Networking Basics section for more information. If you need to change the settings, write down your existing settings
before making any changes. In most cases, your computer should be set to receive an IP address automatically in
which case you will not have to do anything to your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user
name to admin and leave the password box empty. Click OK to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings
to continue.
™
4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save
Settings to continue.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to
save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the
browser and change your computer’s IP settings back to the original values as in Step 1.
12D-Link DIR-615 User Manual
Section 2 - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug
anything into the WAN port of the D-Link router.
8. You may now use the other three LAN ports to connect other Ethernet devices and computers. To configure your
wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration
and Wireless Security sections for more information on setting up your wireless network.
13D-Link DIR-615 User Manual
Section 3 - Configuration
Configuration
This section will show you how to configure your new D-Link wireless router using the web-based configuration
utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
Enter the user name (admin) and your password. Leave
the password blank by default.
If you get a Page Cannot be Displayed error, please
refer to the Troubleshooting section for assistance.
14D-Link DIR-615 User Manual
Section 3 - Configuration
Setup Wizard
You may run the setup wizard from the opening
Internet Setup window to quickly set up your router.
Click Internet Connection Setup Wizard, you will
be directed to the first window of the wizard.
Click Next to continue.
Create a new password and then click Next to
continue.
15D-Link DIR-615 User Manual
Section 3 - Configuration
Select your time zone from the drop-down menu and then click Next
to continue.
Select the type of Internet connection you use and then click Next
to continue.
If you selected Dynamic, you may need to enter the MAC address of the
computer that was last connected directly to your modem. If you are currently
using that computer, click Clone Your PC’s MAC Address and then click
Next to continue.
The Host Name is optional but may be required by some ISPs. The default
host name is the device name of the Router and may be changed.
16D-Link DIR-615 User Manual
Section 3 - Configuration
If you selected PPPoE, enter your PPPoE username and password. Click
Next to continue.
Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Note: Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password. Click
Next to continue.
If you selected L2TP, enter your L2TP username and password. Click Next
to continue.
17D-Link DIR-615 User Manual
Section 3 - Configuration
If you selected Big Pond, enter your Big Pond username and password.
Click Next to continue.
If you selected Static, enter your network settings supplied by your Internet
provider. Click Next to continue.
Click Connect to save your settings.
Please allow 1-2 minutes for rebooting. When the router has finished
rebooting, the opening window will be displayed.
18D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
Static (assigned by ISP)
Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,
gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP
form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
IP Address:
Subnet Mask:
ISP Gateway:
MAC Address:
Clone MAC
Address:
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The default MAC Address is set to the WAN’s physical
interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address
unless required by your ISP.
The default MAC address is set to the WAN’s physical
interface MAC address on the Broadband Router. You
can use the Clone MAC Address button to copy the MAC
address of the Ethernet Card installed by your ISP and
replace the WAN MAC address with the MAC address of the
router. It is not recommended that you change the default
MAC address unless required by your ISP.
Primary DNS
Address:
Secondary DNS
Address:
MTU:
Enter the Primary DNS server IP address assigned by your
ISP.
This is optional.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492
is the default MTU.
19D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
Dynamic
To manually set up the Internet connection, click the Manual Internet Connection Setup button on the Router’s
opening window.
Access
Point
Mode:
Dynamic IP
Address:
Host
Name:
MAC Address:
Clone MAC
Address:
Checking this box disables NAT and turns the Router into
an Access Point only.
Choose Dynamic IP Address to obtain IP Address
information automatically from your ISP. Select this option
if your ISP does not give you any IP numbers to use. This
option is commonly used for Cable modem services.
The Host Name is optional but may be required by some
ISPs. The default host name is the device name of the
Router and may be changed.
The default MAC Address is set to the WAN’s physical
interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address
unless required by your ISP.
The default MAC address is set to the WAN’s physical
interface MAC address on the Broadband Router. You
can use the “Clone MAC Address” button to copy the MAC
address of the Ethernet Card installed by your ISP and
replace the WAN MAC address with the MAC address of the
router. It is not recommended that you change the default
MAC address unless required by your ISP.
DNS
Addresses:
MTU:
Enter the DNS (Domain Name Server) server IP address assigned by your ISP.
Maximum Transmission Unit - You may need to change the MTU for optimal performance with your specific ISP.
20D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
PPPoE
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
PPPoE:
User Name:
Password:
Service Name:
IP Address:
DNS
Addresses:
Maximum Idle
Time:
MTU:
Select Dynamic (most common) or Static. Select Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password
in the next box.
Enter the ISP Service Name (optional).
Enter the IP address (Static PPPoE only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPPoE only).
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable
this feature, enable Auto-reconnect.
Maximum Transmission Unit - You may need to change the
MTU for optimal performance with your specific ISP. 1492
is the default MTU.
Connection
Mode Select:
Select either Always-on, Manual, or Connect-on
demand.
21D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
PPTP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Server IP:
PPTP Account:
PPTP Password:
Select Dynamic (most common) or Static. Select Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your PPTP account name.
Enter your PPTP password and then retype the password
in the next box.
Maximum Idle
Time:
MTU:
Connect Mode:
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Maximum Transmission Unit - You may need to change the
MTU for optimal performance.
Select either Always-on, Manual, or Connect-on demand.
22D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services.
L2TP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Server IP:
L2TP Account:
L2TP
Password:
Select Dynamic (most common) or Static. Select Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter the IP address (Static L2TP only).
Enter the Primary and Secondary DNS Server Addresses
(Static L2TP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your L2TP account name.
Enter your L2TP password and then retype the password
in the next box.
Maximum Idle
Time:
MTU:
Connect Mode:
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Maximum Transmission Unit - You may need to change the
MTU for optimal performance with your specific ISP.
Select either Always-on, Manual, or Connect-on demand.
23D-Link DIR-615 User Manual
Section 3 - Configuration
Internet Setup
Dual Access (for Russia only)
There are two main steps to configure a Dual Access Internet connection for Russia. First, configure a PPPoE connection (as previously
described for PPPoE connections), and add the physical WAN IP settings as instructed from the ISP. Second, configure a PPTP connection
(as previously described for PPTP connections). In addition, the second step also includes an option to use a MAC address that will always
be associated with the connection. The MAC address is entered manually or copied from the computer.
24D-Link DIR-615 User Manual
Section 3 - Configuration
Wireless Setup
Wireless settings for the router may be configured
manually or by using a wizard. To use the wizard,
click the Wireless Connection Setup Wizard button
and then follow the steps that are described below.
To configure the wireless settings manually, click
the Manual Wireless Connection Setup button.
The parameters for this window are described later
in this section. The Wireless Security section that
directly follows this Configuration section provides
additional explanation for how to configure the WEP,
WPA, WPA2, and WPA/WPA2 wireless security
mode options.
Click Next to continue.
Enter a Wireless Network Name in the textbox, which
is also know as the SSID, and then click Next to
continue.
25D-Link DIR-615 User Manual
Section 3 - Configuration
Use the radio buttons to select the desired level of wireless security,
Best, Better, or Good, and then click Next to continue.
Enter a Wireless Security Password in the textbox and then click
Next to continue.
This window displays a summary of your wireless security settings. Please
print this out or record this information in a safe place and then click Save
to continue.
The Router will save your new settings and reboot. When it is finished after
1-2 minutes, the opening Wireless Setup window is displayed.
26D-Link DIR-615 User Manual
Section 3 - Configuration
Wi-Fi
Protected
Setup:
Enable
Wireless:
Wireless
Network Name:
Enable
Wireless
Channel:
To implement Wi-Fi protection, or WCN 2.0, tick the Enable
checkbox, click either Generate New PIN or Reset PIN to
Default, and then configure the Wi-Fi settings below. Please
see the Setting Up Wi-Fi Protection (WCN 2.0 in Windows
Vista) section later in this manual for detailed configuration
information.
Check the box to enable the wireless function. If you do
not want to use wireless, uncheck the box to disable all the
wireless functions.
Service Set Identifier (SSID) is the name of your wireless
network. Create a name using up to 32 characters. The
SSID is case-sensitive.
Indicates the channel setting for the DIR-615. By default
the channel is set to 6. The Channel can be changed to
fit the channel setting for an existing wireless network or
to customize the wireless network. The Auto Channel
Selection setting can be selected to allow the DIR-615 to
choose the channel with the least amount of interference.
Transmission
Rate:
WMM Enable:
Enable Hidden
Wireless:
Use the drop-down menu to select the appropriate Transmission Rate in Mbits per second. Many users will want to use the
default setting, Best (automatic).
Enable Wi-Fi Multimedia to enjoy basic quality of service features. WMM prioritizes traffic according to four access categories:
voice, video, best effort, and background.
Check this option if you would not like the SSID of your wireless network to be broadcasted by the DIR-615. If this option is
checked, the SSID of the DIR-615 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID
of your DIR-615 in order to connect to it.
27D-Link DIR-615 User Manual
Section 3 - Configuration
1. To enable wireless security on the Router, use
the drop-down menu to select the desired option.
To enable WEP, select Enable WEP Wireless
Security (basic).
2. Next to Authentication, select either Open
or Shared Key. Shared Key provides greater
security.
3. Select either 64Bit or 128Bit encryption from the
drop-down menu next to WEP Encryption.
4. Next to Default Key Type, select WEP Key 1 and
enter a WEP key that you create. Make sure you
enter this key exactly on all your wireless devices.
You may enter up to four different keys either using
Hex or ASCII. Hex is recommended (letters A-F and
numbers 0-9 are valid). In ASCII all numbers and
letters are valid.
5. Click Save Settings to save your settings. If you
are configuring the Router with a wireless adapter,
you will lose connectivity until you enable WEP on
your adapter and enter the same WEP key as you
did on the Router.
NOTE:
It is recommended to enable encryption on your wireless
Router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless
signal may degrade when enabling encryption due to the added
overhead.
28D-Link DIR-615 User Manual
Section 3 - Configuration
1. To enable WPA, WPA2, or WPA/WPA2, select
either Enable WPA Only Wireless Security
(enhanced), Enable WPA2 Only Wireless Security
(enhanced), or Enable WPA/WPA2 Wireless
Security (enhanced).
2. Next to Cipher Type, select TKIP, AES, or
Both.
3. Next to PSK/EAP, select PSK.
4. Next to Network Key, enter a
passphrase. The key is an alpha-numeric
password between 8 and 63 characters long.
The password can include symbols (!?*&_) and
spaces. Make sure you enter this key exactly the
same on all other wireless clients.
5. Click Save Settings to save your settings. If you
are configuring the router with a wireless adapter,
you will lose connectivity until you enable WPA,
WPA2, or WPA/WPA2 (whichever of the three
options you have selected above) on your adapter
and enter the same network key as you did on the
router.
29D-Link DIR-615 User Manual
Section 3 - Configuration
1. To enable WPA, WPA2, or WPA/WPA2 for
a RADIUS server, next to Security Mode,
select Enable WPA Only Wireless Security
(enhanced), Enable WPA2 Only Wireless Security
(enhanced), or Enable WPA/WPA2 Wireless
Security (enhanced).
2. Next to Cipher Type, select TKIP, AES, or
Auto.
3. Next to PSK/EAP, select EAP.
4. Next to RADIUS Server 1 enter the IP Address
of your RADIUS server.
5. Next to Port, enter the port you are using with your
RADIUS server. 1812 is the default port.
6. Next to Shared Secret, enter the security key.
7. If you have a secondary RADIUS server, enter its
IP address, port, and secret key.
8. Click Save Settings to save your settings.
30D-Link DIR-615 User Manual
Section 3 - Configuration
LAN Setup
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Router IP
Address:
Default Subnet
Mask:
Local Domain
Name:
Enable DNS
Relay:
Refer to the next page for DHCP information.
Enter the IP address of the router. The default
IP address is 192.168.0.1.
If you change the IP address, once you click
Apply, you will need to enter the new IP address
in your browser to get back into the configuration
utility.
Enter the Subnet Mask. The default subnet mask
is 255.255.255.0.
Enter the Domain name (Optional).
Check the box to transfer the DNS server
information from your ISP to your computers. If
unchecked, your computers will use the router
for a DNS server.
31D-Link DIR-615 User Manual
Loading...